Lantronix MSS manual Change Local Switch, See Also

Page 39

Command Reference

Change Local Switch

Secondary

Configures a loadhost to be used when the primary loadhost is unavailable.

IPaddress

Specify a host using standard numeric format—host names cannot be resolved via a nameserver. Specifying an IP address of 0.0.0.0 removes the previously- defined loadhost.

2.30 Change Local Switch

 character 

CHANGE PORT PortList LOCAL SWITCH 

 NONE 

Defines a key that will allow you to access local mode from within a session. The Local Switch key functions the same as the Break key. Any key can be specified unless it conflicts with MSS line editing or the Break or Forward keys. The key you specify will be stripped from the data stream, so while it won’t interfere with remote operating systems, you will lose any functionality that key would have on local programs.

Restrictions	Requires privileged user status.
Parameters	Port
	MSS4 only. Specifies a particular port or group of ports.
Note:	In the absence of the PortList parameter, the configuration will affect the MSS4’s
	current port only.
	PortList
	Specify a particular port or group of ports. Port numbers are specified with
	integers between 1 and 4, and should be separated with commas (for lists) or
	dashes (for ranges).
	character
	Specify a character to serve as the switch key. To specify a control character,
	use escaped hex (\xx). For example, Ctrl-B (ASCII character 0x02) would be
	specified as \02.
	None
	Disables the Local Switch key.
Defaults	No switch
See Also	Change Backward Switch, page 2-14; Change Break, page 2-15; Change
	Forward Switch, page 2-24.

2-30

Image 39

Contents MSS Reference Manual Part Number Contents Contents Iii Index What’s New Command SyntaxKey Purpose Command Line EditingAbout This Manual HelpCommand Reference Change 80211 Enabled BackwardChange Change 80211 Antenna DefaultsRestrictions Parameters ErrorsChange 80211 Fragmentation Change 80211 MAC AddressExamples Change 80211 Network ModeChange 80211 Region Change 80211 PowerChange 80211 RTS Change 80211 ResetChange 80211 WEP Current port only Change AccessChange Autobaud DefaultsDynamic See AlsoChange Autostart Dashes for ranges Change Bootgateway Change Backward SwitchRestrictions Requires privileged user status ParametersPort Change BootpDefaultsEnabled Change BreakChange Charsize DefaultsNone See AlsoDefaults Bytes Change BufferingChange Datasend Condition has been detected Restrictions Change DedicatedCommand on Change Domain Change DhcpChange DTRWait Change DSRLogoutChange Flow Control DefaultsDisabledChange Gateway Change Forward SwitchChange Inactive Timer DefaultsDisabled See AlsoChange Inactive Logout Change Incoming Change IPSecurity Change IPAddressChange LAT CircTimer Change LAT Groups Change LAT IdentificationChange Loadhost Change Local Switch Change Modem Control Change LoginpassChange Name Change Modem EmulationChange NetWare Encapsulation Change NameserverChange NetWare Loadhost Change NetWare Internal NetworkChange NetWare Routing Change ParityParametersfileserver Change Passflow Change Password Limit Change Password IncomingChange Portname Change Password ProtectChange Preferred Change Rarp Change PrivpassChange Retransmit Limit Change RloginChange RS485 Change Signal Check Change SecondaryChange Session Limit Change SNMPSetComm Change SilentbootChange Speed Change SoftwareTwo colons and the startup file name of up to 47 characters Change StartupDefaults See Also Change StopbitsChange Subnet Mask DefaultsConsole Change TCPKeepaliveChange Telnetdest Change Telnetpad Change TermtypeParameters Examples Daytime is only supported over UDP Change TimeserverChange Wins Change VerifyCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Parametersusername Delete IPSecurityDisconnect FingerForward HostlistParameterskeyword Initialize Show Hostlist commandLogout Port ParametersDelayParametersserviceName 78 LATParametershostname NetstatPing ResumeRlogin 84 RTCParametersIPaddress Set Privileged ShowParametersAntenna Show Nodes Show HostlistShow IPsecurity Show NetWareParametersAll Show PortsShow RS485 Show ServerShow Services ParametersBootparamsShow Session Source Show SnmpShow Users Show Version100 SPX TelnetParametersSAPname Zero TestFull Contact Information Problem Report ProcedureUsage Available StringsMultiple Strings Xxxx Usage ExamplesParametersS 1.5 or1.11 Y Error Bits IntroductionLeftmost Number 02000000 1000000008000000 04000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Security 2-27,2-57,2-64IPX NetWare Login 2-31,2-37UDP 2-50,B-3 Telnet 2-48,2-68