Lantronix MSS manual Change NetWare Internal Network, Change NetWare Loadhost

Page 43

Command ReferenceChange NetWare Internal Network

Parameters

Ether_II

 

Enables Ethernet v2 frame type.

 

Native

 

Enables the “native mode” NetWare frame type.

 

Snap

 

Enables the 802.2 frame type with SNAP SAPs.

 

802_2

 

Enables the 802.2 frame type with NetWare SAPs.

Defaults

all Enabled (Internal routing also enabled)

See Also

Change NetWare Internal Network, page 2-34; Change NetWare Routing,

 

page 2-35; Show NetWare, page 2-64.

2.37 Change NetWare Internal Network

CHANGE NETWARE INTERNAL NETWORK number

Changes the MSS’s preset internal network number, which is derived from the unit’s Ethernet address. This number is used for internal NetWare routing.

Restrictions

Requires privileged user status.

 

The MSSLite, MSS4, and the MSS-VIA do not support Netware.

Parameters

number

 

Specify the new internal network number in the format annnnnnn where a

 

represents a letter and each n represents a number.

See Also

Change NetWare Encapsulation, page 2-33; Change NetWare Routing, page

 

2-35; Show NetWare, page 2-64.

2.38 Change NetWare Loadhost

CHANGE NETWARE LOADHOST

fileserver

NONE

Specifies the name of the fileserver from which download attempts will be made at boot time.

Restrictions

Requires privileged user status.

 

The MSSLite, MSS4, and the MSS-VIA do not support Netware.

2-34

Image 43
Contents MSS Reference Manual Part Number Contents Contents Iii Index What’s New Command SyntaxKey Purpose Command Line EditingAbout This Manual HelpCommand Reference Backward Change 80211 EnabledChange Change 80211 Antenna DefaultsRestrictions Parameters ErrorsChange 80211 Fragmentation Change 80211 MAC AddressExamples Change 80211 Network ModeChange 80211 Region Change 80211 PowerChange 80211 RTS Change 80211 ResetChange 80211 WEP Current port only Change AccessChange Autobaud DefaultsDynamic See AlsoChange Autostart Dashes for ranges Change Bootgateway Change Backward SwitchRestrictions Requires privileged user status ParametersPort Change BootpDefaultsEnabled Change BreakChange Charsize DefaultsNone See AlsoDefaults Bytes Change BufferingChange Datasend Condition has been detected Restrictions Change DedicatedCommand on Change Domain Change DhcpChange DTRWait Change DSRLogoutChange Flow Control DefaultsDisabledChange Gateway Change Forward SwitchDefaultsDisabled See Also Change Inactive TimerChange Inactive Logout Change Incoming Change IPSecurity Change IPAddressChange LAT CircTimer Change LAT Identification Change LAT GroupsChange Loadhost Change Local Switch Change Modem Control Change LoginpassChange Name Change Modem EmulationChange NetWare Encapsulation Change NameserverChange NetWare Loadhost Change NetWare Internal NetworkChange Parity Change NetWare RoutingParametersfileserver Change Passflow Change Password Limit Change Password IncomingChange Portname Change Password ProtectChange Preferred Change Rarp Change PrivpassChange Retransmit Limit Change RloginChange RS485 Change Secondary Change Signal CheckChange Session Limit Change SNMPSetComm Change SilentbootChange Speed Change SoftwareTwo colons and the startup file name of up to 47 characters Change StartupChange Stopbits Defaults See AlsoChange Subnet Mask Change TCPKeepalive DefaultsConsoleChange Telnetdest Change Termtype Change TelnetpadParameters Examples Daytime is only supported over UDP Change TimeserverChange Wins Change VerifyCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Parametersusername Delete IPSecurityDisconnect FingerHostlist ForwardParameterskeyword Initialize Show Hostlist commandLogout Port ParametersDelayParametersserviceName 78 LATParametershostname NetstatPing Resume84 RTC RloginParametersIPaddress Show Set PrivilegedParametersAntenna Show Nodes Show HostlistShow IPsecurity Show NetWareParametersAll Show PortsShow RS485 Show ServerParametersBootparams Show ServicesShow Session Source Show SnmpShow Users Show VersionTelnet 100 SPXParametersSAPname Zero TestFull Contact Information Problem Report ProcedureAvailable Strings UsageMultiple Strings Xxxx Usage ExamplesParametersS 1.5 or1.11 Y Introduction Error BitsLeftmost Number 02000000 1000000008000000 04000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Security 2-27,2-57,2-64IPX NetWare Login 2-31,2-37UDP 2-50,B-3 Telnet 2-48,2-68