Lantronix MSS manual Change Inactive Logout, Change Inactive Timer, DefaultsDisabled See Also

Page 34

Command Reference

Change Inactive Logout

ParametersServer

MSS4 only.

Secondary

Configures a gateway to be used when the primary gateway is unavailable.

IPaddress

Specify a host using the numeric IP address format. Specifying an IP address of 0.0.0.0 removes the previously-defined gateway.

See Also

Change Subnet Mask, page 2-47.

2.21 Change Inactive Logout

DISABLED

CHANGE PORT PortList INACTIVE LOGOUT   ENABLED

Determines whether a port will be automatically logged out after a period of inactivity. Any open connections will be closed before logout. Inactivity is defined as having no keyboard or network activity on the port. The inactivity period is set with the Change Inactive Timer command.

Restrictions

Requires privileged user status.

ParametersPort

MSS4 only. Specifies a particular port or group of ports.

Note: In the absence of the PortList parameter, the configuration will affect the MSS4’s current port only.

PortList

Specify a particular port or group of ports. Port numbers are specified with integers between 1 and 4, and should be separated with commas (for lists) or dashes (for ranges).

DefaultsDisabled

See Also

Change Inactive Timer, page 2-25.

2.22 Change Inactive Timer

CHANGE

SERVER

INACTIVE TIMER period

Sets the period of time after which a port with Inactive Logout enabled will be considered inactive and automatically logged out.

Restrictions

Requires privileged user status.

2-25

Image 34
Contents MSS Reference Manual Part Number Contents Contents Iii Index Command Syntax What’s NewCommand Line Editing Key PurposeHelp About This ManualCommand Reference Backward Change 80211 EnabledChange Defaults Change 80211 AntennaRestrictions Change 80211 MAC Address ErrorsChange 80211 Fragmentation ParametersChange 80211 Network Mode ExamplesChange 80211 Power Change 80211 RegionChange 80211 Reset Change 80211 RTSChange 80211 WEP Change Access Current port onlyDefaultsDynamic See Also Change AutobaudChange Autostart Dashes for ranges Change Backward Switch Change BootgatewayChange Break Change BootpDefaultsEnabled Restrictions Requires privileged user status ParametersPortChange Buffering DefaultsNone See AlsoDefaults Bytes Change CharsizeChange Datasend Condition has been detected Change Dedicated RestrictionsCommand on Change Dhcp Change DomainChange DSRLogout Change DTRWaitDefaultsDisabled Change Flow ControlChange Forward Switch Change GatewayDefaultsDisabled See Also Change Inactive TimerChange Inactive Logout Change Incoming Change IPAddress Change IPSecurityChange LAT CircTimer Change LAT Identification Change LAT GroupsChange Loadhost Change Local Switch Change Loginpass Change Modem ControlChange Modem Emulation Change NameChange Nameserver Change NetWare EncapsulationChange NetWare Internal Network Change NetWare LoadhostChange Parity Change NetWare RoutingParametersfileserver Change Passflow Change Password Incoming Change Password LimitChange Password Protect Change PortnameChange Preferred Change Privpass Change RarpChange Rlogin Change Retransmit LimitChange RS485 Change Secondary Change Signal CheckChange Session Limit Change Silentboot Change SNMPSetCommChange Software Change SpeedChange Startup Two colons and the startup file name of up to 47 charactersChange Stopbits Defaults See AlsoChange Subnet Mask Change TCPKeepalive DefaultsConsoleChange Telnetdest Change Termtype Change TelnetpadParameters Examples Change Timeserver Daytime is only supported over UDPChange Verify Change WinsCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Finger Delete IPSecurityDisconnect ParametersusernameHostlist ForwardParameterskeyword Show Hostlist command Initialize78 LAT ParametersDelayParametersserviceName Logout PortResume NetstatPing Parametershostname84 RTC RloginParametersIPaddress Show Set PrivilegedParametersAntenna Show NetWare Show HostlistShow IPsecurity Show NodesShow Server Show PortsShow RS485 ParametersAllParametersBootparams Show ServicesShow Session Show Version Show SnmpShow Users SourceTelnet 100 SPXParametersSAPname Test ZeroProblem Report Procedure Full Contact InformationAvailable Strings UsageMultiple Strings Usage Examples Xxxx1.5 or ParametersS1.11 Y Introduction Error BitsLeftmost Number 04000000 1000000008000000 02000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Login 2-31,2-37 Security 2-27,2-57,2-64IPX NetWareTelnet 2-48,2-68 UDP 2-50,B-3