Lantronix MSS manual Change Secondary, Change Session Limit, Change Signal Check

Page 52

Command Reference

Change Secondary

 

TXDrive

 

Controls how the MSS drives the TX pin.

 

Always

 

Sets the MSS to drive TX. The MSS will never tristate TX, even if data is not

 

being sent.

 

Auto

 

Sets the MSS to drive TX only when transmitting, and tristate when not

 

transmitting.

Defaults

Disabled

 

Mode = 4Wire

 

Termination disabled

 

TXDrive = Always

2.52 Change Secondary

Users can configure a secondary gateway, loadhost, and/or nameserver in case the primaries are unreachable. For information, please see the Change Gateway (page 2-24),Change Loadhost (page 2-29),and Change Nameserver (page 2-33)command entries.

2.53 Change Session Limit

CHANGE SERVER

SESSION LIMIT number

Sets a server-wide limit for active sessions per port.

Restrictions

Requires privileged user status.

Parameters

Server

 

MSS4 only.

 

number

 

Enter a value between 0 and 8.

Defaults

4

2.54 Change Signal Check

DISABLED

CHANGE PORT PortList SIGNAL CHECK   ENABLED

Determines whether the MSS will check for the DSR signal when connections are made from the network to a serial port. If the DSR signal is not present, the connection will be rejected.

2-43

Image 52
Contents MSS Reference Manual Part Number Contents Contents Iii Index Command Syntax What’s NewCommand Line Editing Key PurposeHelp About This ManualCommand Reference Backward Change 80211 EnabledChange Defaults Change 80211 AntennaRestrictions Errors Change 80211 FragmentationChange 80211 MAC Address ParametersChange 80211 Network Mode ExamplesChange 80211 Power Change 80211 RegionChange 80211 Reset Change 80211 RTSChange 80211 WEP Change Access Current port onlyDefaultsDynamic See Also Change AutobaudChange Autostart Dashes for ranges Change Backward Switch Change BootgatewayChange Bootp DefaultsEnabledChange Break Restrictions Requires privileged user status ParametersPortDefaultsNone See Also Defaults BytesChange Buffering Change CharsizeChange Datasend Condition has been detected Change Dedicated RestrictionsCommand on Change Dhcp Change DomainChange DSRLogout Change DTRWaitDefaultsDisabled Change Flow ControlChange Forward Switch Change GatewayDefaultsDisabled See Also Change Inactive TimerChange Inactive Logout Change Incoming Change IPAddress Change IPSecurityChange LAT CircTimer Change LAT Identification Change LAT GroupsChange Loadhost Change Local Switch Change Loginpass Change Modem ControlChange Modem Emulation Change NameChange Nameserver Change NetWare EncapsulationChange NetWare Internal Network Change NetWare LoadhostChange Parity Change NetWare RoutingParametersfileserver Change Passflow Change Password Incoming Change Password LimitChange Password Protect Change PortnameChange Preferred Change Privpass Change RarpChange Rlogin Change Retransmit LimitChange RS485 Change Secondary Change Signal CheckChange Session Limit Change Silentboot Change SNMPSetCommChange Software Change SpeedChange Startup Two colons and the startup file name of up to 47 charactersChange Stopbits Defaults See AlsoChange Subnet Mask Change TCPKeepalive DefaultsConsoleChange Telnetdest Change Termtype Change TelnetpadParameters Examples Change Timeserver Daytime is only supported over UDPChange Verify Change WinsCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Delete IPSecurity DisconnectFinger ParametersusernameHostlist ForwardParameterskeyword Show Hostlist command InitializeParametersDelay ParametersserviceName78 LAT Logout PortNetstat PingResume Parametershostname84 RTC RloginParametersIPaddress Show Set PrivilegedParametersAntenna Show Hostlist Show IPsecurityShow NetWare Show NodesShow Ports Show RS485Show Server ParametersAllParametersBootparams Show ServicesShow Session Show Snmp Show UsersShow Version SourceTelnet 100 SPXParametersSAPname Test ZeroProblem Report Procedure Full Contact InformationAvailable Strings UsageMultiple Strings Usage Examples Xxxx1.5 or ParametersS1.11 Y Introduction Error BitsLeftmost Number 10000000 0800000004000000 02000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Login 2-31,2-37 Security 2-27,2-57,2-64IPX NetWareTelnet 2-48,2-68 UDP 2-50,B-3