Lantronix MSS manual Change 80211 Reset, Change 80211 RTS

Page 17

Command Reference	Change 80211
Parameters	Regions
	IC: Canada
	ETSI: Europe, most countries (verify with your local regulatory body)
	SPAIN: Spain
	FRANCE: France
	MKK: Japan
Defaults	FCC
Examples	Local>> CHANGE 80211 REGION FRANCE
	Local>> CHANGE 80211 RESET
See Also	Show 80211, page 2-63

2.2.10 Change 80211 Reset

CHANGE 80211 RESET

Resets the MSS so any configuration changes will take effect immediately.

Restrictions	Requires privileged user status.
	Only applies to the MSS-VIA and certain MSS4 models.
Parameters	Reset
	Resets the MSS to make all 802.11 changes take effect immediately. This
	command should be entered anytime you make an 802.11 configuration
	change. It also clears out any previous errors and starts over with the current
	802.11 parameters.
See Also	Show 80211, page 2-63

2.2.11 Change 80211 RTS

CHANGE 80211 RTS num

Changes the RTS threshold value.

Any configuration changes you make will not take place until you issue the Change 80211 Reset command.

Restrictions	Requires privileged user status.
	Only applies to the MSS-VIA and certain MSS4 models.
Errors	If you enter a command that is not applicable to the 802.11 card currently in
	use, you will receive an Error message.

2-8

Image 17

Contents MSS Reference Manual Part Number Contents Contents Iii Index What’s New Command SyntaxKey Purpose Command Line EditingAbout This Manual HelpCommand Reference Change Change 80211 EnabledBackward Change 80211 Antenna DefaultsRestrictions Change 80211 Fragmentation ErrorsChange 80211 MAC Address ParametersExamples Change 80211 Network ModeChange 80211 Region Change 80211 PowerChange 80211 RTS Change 80211 ResetChange 80211 WEP Current port only Change AccessChange Autobaud DefaultsDynamic See AlsoChange Autostart Dashes for ranges Change Bootgateway Change Backward SwitchDefaultsEnabled Change BootpChange Break Restrictions Requires privileged user status ParametersPortDefaults Bytes DefaultsNone See AlsoChange Buffering Change CharsizeChange Datasend Condition has been detected Restrictions Change DedicatedCommand on Change Domain Change DhcpChange DTRWait Change DSRLogoutChange Flow Control DefaultsDisabledChange Gateway Change Forward SwitchChange Inactive Logout Change Inactive TimerDefaultsDisabled See Also Change Incoming Change IPSecurity Change IPAddressChange LAT CircTimer Change Loadhost Change LAT GroupsChange LAT Identification Change Local Switch Change Modem Control Change LoginpassChange Name Change Modem EmulationChange NetWare Encapsulation Change NameserverChange NetWare Loadhost Change NetWare Internal NetworkParametersfileserver Change NetWare RoutingChange Parity Change Passflow Change Password Limit Change Password IncomingChange Portname Change Password ProtectChange Preferred Change Rarp Change PrivpassChange Retransmit Limit Change RloginChange RS485 Change Session Limit Change Signal CheckChange Secondary Change SNMPSetComm Change SilentbootChange Speed Change SoftwareTwo colons and the startup file name of up to 47 characters Change StartupChange Subnet Mask Defaults See AlsoChange Stopbits Change Telnetdest DefaultsConsoleChange TCPKeepalive Parameters Examples Change TelnetpadChange Termtype Daytime is only supported over UDP Change TimeserverChange Wins Change VerifyCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Disconnect Delete IPSecurityFinger ParametersusernameParameterskeyword ForwardHostlist Initialize Show Hostlist commandParametersserviceName ParametersDelay78 LAT Logout PortPing NetstatResume ParametershostnameParametersIPaddress Rlogin84 RTC ParametersAntenna Set PrivilegedShow Show IPsecurity Show HostlistShow NetWare Show NodesShow RS485 Show PortsShow Server ParametersAllShow Session Show ServicesParametersBootparams Show Users Show SnmpShow Version SourceParametersSAPname 100 SPXTelnet Zero TestFull Contact Information Problem Report ProcedureMultiple Strings UsageAvailable Strings Xxxx Usage ExamplesParametersS 1.5 or1.11 Y Leftmost Number Error BitsIntroduction 08000000 1000000004000000 02000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Security 2-27,2-57,2-64IPX NetWare Login 2-31,2-37UDP 2-50,B-3 Telnet 2-48,2-68