Lantronix MSS manual Crypt Password, See Also

Page 61

Command Reference

Crypt Password

2.69 Crypt Password

CRYPT PASSWORD password

Changes the password used for the encryption mode environment string (:Y). Both ends of the connection must agree on the encryption password being used. You must reboot after changing the encryption password.

Note: To use the encryption features for your MSS, you must use a special software file. Contact Lantronix for more information.

This command can be used to configure an MSS to MSS encrypted session. Set the encryption password on both units to be the same password, reboot both units, then telnet either to one of the unit’s local prompts (i.e. socket 2100) or serial port (i.e. socket 210x where x is the serial port number) using the :Y environment string. Sockets 2100 and 210x are assumed to be encrypted on the receiving MSS.

Restrictions

Requires privileged user status.

Parameterspassword

Enter a new encryption password. The password can be up to 7 alphanumeric or escaped hex (\xx) characters and is case sensitive.

See Also

Change Dedicated, page 2-19; Hostlist, page 2-58.

2-52

Image 61

Contents MSS Reference Manual Part Number Contents Contents Iii Index What’s New Command SyntaxKey Purpose Command Line EditingAbout This Manual HelpCommand Reference Backward Change 80211 EnabledChange Change 80211 Antenna DefaultsRestrictions Change 80211 Fragmentation ErrorsChange 80211 MAC Address ParametersExamples Change 80211 Network ModeChange 80211 Region Change 80211 PowerChange 80211 RTS Change 80211 ResetChange 80211 WEP Current port only Change AccessChange Autobaud DefaultsDynamic See AlsoChange Autostart Dashes for ranges Change Bootgateway Change Backward SwitchDefaultsEnabled Change BootpChange Break Restrictions Requires privileged user status ParametersPortDefaults Bytes DefaultsNone See AlsoChange Buffering Change CharsizeChange Datasend Condition has been detected Restrictions Change DedicatedCommand on Change Domain Change DhcpChange DTRWait Change DSRLogoutChange Flow Control DefaultsDisabledChange Gateway Change Forward SwitchDefaultsDisabled See Also Change Inactive TimerChange Inactive Logout Change Incoming Change IPSecurity Change IPAddressChange LAT CircTimer Change LAT Identification Change LAT GroupsChange Loadhost Change Local Switch Change Modem Control Change LoginpassChange Name Change Modem EmulationChange NetWare Encapsulation Change NameserverChange NetWare Loadhost Change NetWare Internal NetworkChange Parity Change NetWare RoutingParametersfileserver Change Passflow Change Password Limit Change Password IncomingChange Portname Change Password ProtectChange Preferred Change Rarp Change PrivpassChange Retransmit Limit Change RloginChange RS485 Change Secondary Change Signal CheckChange Session Limit Change SNMPSetComm Change SilentbootChange Speed Change SoftwareTwo colons and the startup file name of up to 47 characters Change StartupChange Stopbits Defaults See AlsoChange Subnet Mask Change TCPKeepalive DefaultsConsoleChange Telnetdest Change Termtype Change TelnetpadParameters Examples Daytime is only supported over UDP Change TimeserverChange Wins Change VerifyCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Disconnect Delete IPSecurityFinger ParametersusernameHostlist ForwardParameterskeyword Initialize Show Hostlist commandParametersserviceName ParametersDelay78 LAT Logout PortPing NetstatResume Parametershostname84 RTC RloginParametersIPaddress Show Set PrivilegedParametersAntenna Show IPsecurity Show HostlistShow NetWare Show NodesShow RS485 Show PortsShow Server ParametersAllParametersBootparams Show ServicesShow Session Show Users Show SnmpShow Version SourceTelnet 100 SPXParametersSAPname Zero TestFull Contact Information Problem Report ProcedureAvailable Strings UsageMultiple Strings Xxxx Usage ExamplesParametersS 1.5 or1.11 Y Introduction Error BitsLeftmost Number 08000000 1000000004000000 02000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Security 2-27,2-57,2-64IPX NetWare Login 2-31,2-37UDP 2-50,B-3 Telnet 2-48,2-68