Modero Table Top Cable Wiring Table, Wire Connector | AMX NXT-CV7

CV7 Touch Panel Accessories

The following table provides the wiring information (color coding) for each of the three available cable connectors on each side of the Modero Table Top Cable.

Modero Table Top Cable Wiring Table

Wire	Connector 1	Connector 2	Connector 3

1	White/Orange	White/Orange	Red

2	Orange/White	Orange/White	Black

3	White/Green	White/Green	-

4	Blue/White	Blue/White	-

5	White/Blue	White/Blue	-

6	Green/White	Green/White	-

7	White/Brown	White/Brown	-

8	Brown/White	Brown/White	-

The following figures provide a cross-section view (FIG. 12) and a description (FIG. 13) of the Modero Table Top Cable:

Connector #1 & 2	Element #1
Connector #1 & 2
	Binder

Element #2

		Connector #3
		Jacket
FIG. 12 Table Top Cable - cross-section view
DESCRIPTION:	9/PAIRS COMPOSITE CABLE CONSISTING OF: ELEMENT #1:
	TWO 4/PAIR 24 AWG STRANDED TINNED COPPER,
	POLYETHYLENE INSULATION, ELEMENT #2: 1/PAIR 18 AWG
	STRANDED TNNED COPPER, PVC INSULATION AND FOIL
	SHIELDED OVERALL PAPER BINDER AND FLEX-PVC JACKET.
ELEMENT #1:	2 X 4/PAIRS:	24 AWG STRANDED COPPER
CONDUCTOR:	24 AWG 7/32 TINNED COPPER; OD .024" NOMINAL
INSULATION:	.0075" WALL POLYETHYLENE; OD .039" NOMINAL
COLOR CODE:	P1: WHITE/BLUE, BLUE
	P2: WHITE/ORANGE, ORANGE
	P3: WHITE/GREEN, GREEN
	P4: WHITE/BROWN, BROWN
PAIR:	2 CONDUCTORS TWINNED LEFT HAND LAY
	(TWISTED AT VARIED LAYS TO MINIMIZE CROSS TALK)
CABLE:	4/P CABLED LEFT HAND LAY (BLUE BINDER, ORANGE BINDER)
BINDER:	PAPER TAPE
ELEMENT #2:	1 PAIR: 18 AWG SHIELDED
CONDUCTOR: 18 AWG 16/30 TINNED COPPER; OD .046" NOMINAL
INSULATION:	.010" WALL PVC; OD .066" NOMINAL
COLOR CODE:	BLACK, RED
DRAIN WIRE:	#22 7/30 TINNED COPPER
SHIELD:	ALUM/POLYESTER TAPE (FOIL SIDE IN)
FINAL ASSEMBLY:	TWO ELEMENT #1 & ELEMENT #2 CABLED ON COMMON
	AXIS TO MINIMIZE DIAMETER
BINDER:	CLOTH TAPE 25% OVERLAP
JACKET:	.045" WALL FLEXIBLE PVC,
COLOR:	BLACK MATT
DIAMETER:	.375 INCHES NOMINAL
MARKING:	NONE

FIG. 13 Table Top Cable - Specification Elements

7" Modero Widescreen Touch Panels	13

Image 21

AMX NXT-CV7, NXD-CV7 instruction manual Modero Table Top Cable Wiring Table, Wire Connector

Contents

NXD-CV7 and NXT-CV7 AMX Limited Warranty and Disclaimer FCC Information Page Table of Contents Panel Calibration Upgrading Modero Firmware Programming 113 FG2258-02 CV7 7 Widescreen Video Touch Panel KitsFG2258-01 FG2258-02K NXT-CV7 and NXD-CV7 front views Specifications for 7 Widescreen Video Touch Panels CV7 Specifications Rear Panel Components Front Panel Components Optional Accessories Included AccessoriesCont Button Assignments NXA-AVB/ETHERNET CAT5 CV7 Panels Connector Layout Product Specifications NXA-AVB/ETHERNET SpecificationsNXA-AVB/ETHERNET Breakout Box FG2254-10 Installing the NXA-AVB/ETHERNET Rear ComponentsPanels only Wiring the NXA-AVB/ETHERNET connectors and cables Audio In Left ChannelAudio In Right Channel PWR Wiring the NXA-AVB/ETHERNET for Unbalanced Audio Wiring the NXA-AVB/ETHERNET for Balanced Audio Modero Table Top Cable CA2250-50Balanced OUT Modero Table Top Cable Specifications Wiring information for the Modero Table Top cableMaximum Table Top Cable Lengths for Modero Panels Wire Connector Modero Table Top Cable Wiring Table Specifications for NXA-WC80211B/CF NXA-WC80211B/CF 802.11b Wireless Card FG2255-03 Removing the NXT Outer Housing Installation of the Wireless Card Table Top Panel Do not Remove these screws Slot Card Removal Grooves Card removal grooves Removal of the outer housing and wireless card location Closing and Securing the NXT Enclosure Removing/installing a compact flash card Removing the existing NXD Outer Housing Installation of the Wireless Card WallMount Panel Replacing and Securing the NXD Enclosure Installing the Upgrade Components NXD NXT-BP Power Pack FG2255-10 Optional Compact Flash UpgradesNXA-CFSP Compact Flash Specifications for the NXT-BP NXA-BASE/1 Battery Base Kit FG2255-05KSpecifications for the NXA-BASE/1 Power Voltage Installing an NXT-BP into the NXA-BASE/1 Checking the NXT-BP chargeFront Installing the NXA-BASE/1 below an NXT-CV7 Panel Battery not shown For illustration purposes FrontBack Charging the NXT-BP using the NXA-BASE/1 NXT-CHG Battery Charger Kit FG2255-50K Specifications for NXT-BP and NXT-CHG Powering the NXT-CHGReading the NXT-CHG LED Indicator Charging the NXT-BP batteries using the NXT-CHG Recalibrating the batteriesGreen Solid CV7 Touch Panel Accessories Installing the Internal Components Installing the No-Button Trim RingUnpacking the Panel Removing the default Button Trim Ring Inserting the No-Button Trim Ring Installing the Button Trim Ring Removing the No-Button Trim Ring CB-TP7 conduit box components Pre-Wall Installation of the Conduit Box Installing the NXD panel within a Conduit Box Installation of an NXD Touch Panel Installing the NXD into drywall using Expansion Clips NXD-CV7 Wall Mount panel dimensions using expansion clips Installation Installing the NXD into a Flat Surface using #4 screws Along the edges Installation Wiring Guidelines for the CV7 Panels Preparing captive wiresUsing the PSN NetLinx connector for power Ethernet 10/100 Base-T RJ-45 Connections and Wiring Audio/Video RJ-45 Connections and WiringEthernet RJ-45 Pinouts and Signals Audio/Video RJ-45 Pinout Information RJ-45 wiring diagram Connecting and Using USB Input Devices Installation Second press/hold Calibrating the Modero Panel Touch Panel Calibration Screens Testing your Calibration Modero Setup and System Connection Configuring Communication Protected Setup Configuring and Using USB with a Virtual Master Setup the Panel and PC for USB CommunicationConfirm the Installation of the USB Driver on the PC USB System Connection page using a USB Connection Type Confirm and View the current AMX USB device connections Installed prior to setting up a USB connection to the panel Device Manager dialog showing USB device Before beginning Confirm and View the current AMX USB device connections Secondary Connection Page Wireless Access Overview IP RoutingHot Swapping Configuring Communication Configuring a Wireless Network Access Configure the Panel’s Wireless IP SettingsWireless communication using a Dhcp Address Wireless communication using a Static IP Address Following sections use an NXA-WAP200G and the target WAP Configure the Card’s Wireless Security Settings Procedures Secondary Connection page Wireless Settings section These WEP Key identifier values must match for both devices WEP Key # Keyboard Configure the Panel’s Wired IP Settings Configuring a Wired Ethernet Connection Configuring Communication Configure an Ethernet Connection Type Choose a Master Connection Mode Setting Obtained From NetLinx Master These must match Configuring Communication URL List dialog Using G4 Web Control to Interact with a G4 Panel G4 Web Control Accessing the NetLinx Master via an IP Address Web Control VNC installation and Password entry screens Using your NetLinx Master to Control the G4 panel Connection Details dialog Configuring Communication Upgrading the Modero Firmware via the USB port Configure the panel for a USB Connection Type Prepare NetLinx Studio for communication via the USB port Default Modero panel value is Confirm and Upgrade the firmware via the USB port Select the panel’s KIT file from the Files section Prepare the Master for communication via an IP Upgrading the Modero Firmware via Ethernet IP Address Prepare the panel for communication via an IP Assigning Communication Settings and TCP/IP Settings Select the panel’s KIT file from the Files section FIG Verify and Upgrade the panel firmware via an IP Device and System values Setup Navigation Button Elements Setup Navigation Buttons Setup Page Elements Setup Timeout Display/Panel TimeoutConnection Status Inactivity Page Flip Project Information Page Elements Project Information Panel Information Page Elements Panel Information RAM Time & Date Setup Time Date Refresh/Set Time & Date Setup Page ElementsTime Display fields Date Display fields Volume Page Elements Volume Video Adjustment Protected SetupDefault Panel Sounds Supported sampling rates for WAV Video Setup Page Elements Battery Base Page Elements Battery BaseLow Battery Warning Charge Status Reaches a point where it needs to be recalibrated Battery Status fieldsLimit Protected Setup Navigation Button Elements Protected Setup Navigation Buttons Protected Setup Page Elements Protected SetupReboot Panel Device Number Slider System Recovery G4 Web Control Settings G4 Web ControlG4 Web Control Page Elements G4 Web Control Timeout Sensor Setup Sensor Setup Page Elements Dim Mode MinimumLight Sensor Motion Sensor Wake Panel On MotionSense Password Setup Page Elements Password SetupPanel Password Change Secondary Connection Calibration Secondary Connection Page Elements Access Point MAC Wireless SettingsAddress 108 System Connection Full Duplex System Connection Page Elements ICSNet is not a supported option on this panel Master Connection Firmware Pages and Descriptions 112 Commands CommandsButton Assignments @PDR-popup page namereset flag Sendcommand Panel,@DPG-Popup1Group1Sendcommand Panel,@PDR-Popup11 Sendcommand Panel,@PHE-Popup1Slide to Left Commands Sendcommand Panel,@PPM-Popup11 Sendcommand Panel,@PPM-Popup1ModalSendcommand Panel,@PPN-Popup1Main Sendcommand Panel,@PPN-Popup1 Sendcommand Panel,@PSP-Popup1100,0 Sendcommand Panel,@PSE-Popup1Slide from LeftSendcommand Panel,@PST-Popup150 Sendcommand Panel,PAGE-Page1 Sendcommand Panel,PPOF-Popup1 Sendcommand Panel,PPOF-Popup1MainSendcommand Panel,PPOG-Popup1Main Sendcommand Panel,PPOG-Popup1 RGB triplets and names for basic 88 colors Programming NumbersRGB Values for all 88 Basic Colors Index No Name Red Green Blue 120 Font styles and ID numbers Default Font Styles and ID NumbersFont ID # Font type Size Variable Fonts start at Border Styles and Programming Numbers Border styles and Programming numbersTPD4 Border Styles by Name Border styles Modero Widescreen Touch Panels 123 Button Commands Button Commands Sendcommand Panel,BCF-500.504&510.515,1,12 Sendcommand Panel,BCB-500.504&510,1,12Sendcommand Panel,BCF-500.504&510.515,1,Yellow Sendcommand Panel,BCF-500.504&510.515,1,#F4EC0A63 Sendcommand Panel,BFB-500,Momentary Button Commands Sendcommand Panel,BLN-500,55 Sendcommand Panel,BIM-500,AAAAAAAAAABIM-vt addr range,input mask BLN-vt addr range,button states range,number BMC Sendcommand Panel,BMC- 150,1,1,315,1,%BR%FT%TX%BM%IC%CF%CT BMF BMF-vt addr range,button states range,data Modero Widescreen Touch Panels 131 Sendcommand Panel,BML-500,20 Sendcommand Panel,BMI-530,1&2,newMac.pngSendcommand Panel,BMP-500.504&510.515,1,bitmap.png BNC-vt addr range,command value Sendcommand Panel,BNT-973,5000 Sendcommand Panel,BNN-973,192.168.169.99Sendcommand Panel,BOP-500.504&510.515,1,200 Sendcommand Panel,BOP-500.504&510.515,1,#C8 Sendcommand Panel,BOR-500.504&510,AMX Elite -M Sendcommand Panel,BOR-500.504&510.515,10Sendcommand Panel,BOS-500,1,1 Sendcommand Panel,BPP-500,1 Sendcommand Panel,BSF-500,1 Sendcommand Panel,BRD-500.504&510.515,1&2,Quad LineSendcommand Panel,BSM-500 Sendcommand Panel,BSO-500,1&2,music.wav Sendcommand Panel,BVN-500,191.191.191.191 Sendcommand Panel,BVL-500,0BVP-vt addr range,network password Sendcommand Panel,BVP-500,PCLOCK Send Command Panel,DPF-409,Prev Sendcommand Panel,CPF-500ENA-vt addr range,command value Sendcommand Panel,ENA-500.504&510.515,0 Sendcommand Panel,GIV-500,3 Sendcommand Panel,GDI-7,128Sendcommand Panel,GLH-500,1000 Sendcommand Panel,GLL-500,150 Sendcommand Panel,GRU-500,100 Sendcommand Panel,GRD-500,200Sendcommand Panel,GSC-500,12 Sendcommand Panel,GSN-500,Ball Sendcommand Panel,JSB-500.504&510.515,1&2,1 Sendcommand Panel,ICO-500.504&510.515,1&2,1Sendcommand Panel,JSI-500.504&510.515,1&2,1 ICO-vt addr range,button states range,icon Send Command Panel,MBT-1 Sendcommand Panel,JST-500.504&510.515,1&2,1Send Command Panel,MDC SHO-vt addr range,command value Sendcommand Panel,TEF-500.504&510.515,1&2,Soft Drop Sendcommand Panel,TEC-500.504&510.515,1&2,12Sendcommand Panel,TXT-500.504&510.515,1&2,Test Only TEC-vt addr range,button states range,color Sendcommand TP,UNI-1,0,0041 Sendcommand Panel,UNI-500,1,0041UNI-vt addr range,button states range,unicode text UNI Text Effects Text Effect Names Defineevent Button Query Commands Send Command Panel,?BCB-529,1 Button Query CommandsCustom Event Fields ?BCB-vt addr range,button states range Send Command Panel,?BCT-529,1 Send Command Panel,?BCF-529,1Get the current fill ?BCF-vt addr range,button states range ?BCT-vt addr range,button states range Send Command Panel,?BOP-529,1 Send Command Panel,?BMP-529,1?BMP-vt addr range,button states range ?BOP-vt addr range,button states range Send Command Panel,?BWW-529,1 Send Command Panel,?BRD-529,1?BRD-vt addr range,button states range ?BWW-vt addr range,button states range Send Command Panel,?ICO-529,1&2 Send Command Panel,?FON-529,1?FON-vt addr range,button states range ?ICO-vt addr range,button states range Send Command Panel,?JSI-529,1 Send Command Panel,?JSB-529,1?JSB-vt addr range,button states range ?JSI-vt addr range,button states range Send Command Panel,?TEC-529,1 Send Command Panel,?JST-529,1?JST-vt addr range,button states range ?TEC-vt addr range,button states range Send Command Panel,?TXT-529,1 Send Command Panel,?TEF-529,1?TEF-vt addr range,button states range ?TXT-vt addr range,button states range,optional Panel Runtime Operations Panel Runtime Operation Commands Send Command Panel,@AKR Send Command Panel,@AKP-12345678ENTER PasswordSend Command Panel,BEEP Send Command Panel,BRIT-50 Send Command Panel,PKEYP-123456789 Send Command Panel,@EKP-33333333Enter PasswordSend Command Panel,@PKP-1234567ENTER Password Send Command Panel,SETUP Send Command Panel,@TKP-999.222.1211Enter Phone Send Command Panel,@SOU-Music.wavSend Command Panel,TPAGEON Send Command Panel,TPAGEOFF Input Commands Input Commands Embedded codes Embedded CodesDecimal numbers Hexidecimal values Virtual keystroke Panel Setup Commands Panel Setup Commands Dynamic Image Commands Dynamic Image Commands Embedded Codes Parameter Description RAF-resource name,data Troubleshooting Information My Battery Base page doesn’t Symptom Solution Updated my panel firmware butMy NXT-BP battery pack is Life indicator Connecting Symptom SolutionWas using the power from NXA-BASE/1 battery base to Powered panel My battery from within anNXA-BASE/1 connected to a My WEP doesn’t seem to be Providing power After downloading a panel file or Symptoms includeConnected to my System Master Only one shows up Troubleshooting 168 Bargraph Text Code Inputs Text Formatting Codes for Bargraphs/JoysticksFormatting Code Operations Example Input mask character types Text Area Input MaskingCharacter Types Character Masking Rule Input mask next field characters Input mask rangesInput mask operations Input mask literals Input mask output examples Output ExamplesCommon Name Input Mask Special escape sequences URL ResourcesEscape Sequences Sequence Panel Information 174 Appendix Widescreen Modero Touch Panels 175 RevisionLast15/08/04