Specifications for NXT-BP and NXT-CHG | AMX NXD-CV7, NXT-CV7

CV7 Touch Panel Accessories

Specifications for NXT-BP and NXT-CHG

Dimensions (HWD):	• 1.13" x 8.63" x 11.81" (2.86 cm x 21.91 cm x 30.00 cm)

Power Requirements:	• NXT-BP Battery Voltage - 11.1 Volts
	• NXT-CHG: 90 - 264 VAC, 47-63 Hz, Single Phase
	(using the included 24 VDC power supply)

Weight:	• 0.57 lbs (0.26 kg)

Features:	• Charge time for two depleted batteries: ~ 5 hours
	• Charge Rate: 2.5 A @ 12 VDC
	• 2-Bays: Sequential charging
	• LED: One LED indicator in front of each bay which conveys the status of that
	bay. Refer to the Reading the NXT-CHG LED Indicator section for more
	information.
	• Recalibration pushbutton (located between the bays): Initiates recalibration
	sequence in the left bay only.
	• Recalibration Time: less than 9 hours

Optional Accessories:	• NXT-CHG Kit (FG2250-50K):
	- 1 charger and 2 NXT-BP batteries
	• NXT-BP battery pack (FG2255-10) (additional)

Powering the NXT-CHG

Recalibration improves the reporting accuracy of the battery charge back to the

Modero panel.

The NXT-CHG Smart Battery Charger uses an included power supply to charge inserted batteries.

1.Connect the rear of the NXT-CHG to the power adapter.

2.Connect the power adapter to the provided power cord (with plug).

3.Provide power to the unit by connecting the power cord (with plug) into a power outlet that meets the requirements outlined in the Specifications section for the NXT-CHG.

Reading the NXT-CHG LED Indicator

FIG. 29 shows the components on the NXT-CHG Smart Battery Charger.

Slot 1 (recalibration)

Slot 2

Slot 1

LED

Slot 2

LED

Recalibrate

Pushbutton

FIG. 29 Component locations on the NXT-CHG

	26	7" Modero Widescreen Touch Panels

Image 34

AMX NXD-CV7, NXT-CV7 Specifications for NXT-BP and NXT-CHG, Powering the NXT-CHG, Reading the NXT-CHG LED Indicator

Contents

NXD-CV7 and NXT-CV7 AMX Limited Warranty and Disclaimer FCC Information Page Table of Contents Panel Calibration Upgrading Modero Firmware Programming 113 FG2258-01 CV7 7 Widescreen Video Touch Panel KitsFG2258-02 FG2258-02K NXT-CV7 and NXD-CV7 front views CV7 Specifications Specifications for 7 Widescreen Video Touch Panels Front Panel Components Rear Panel Components Cont Included AccessoriesOptional Accessories Button Assignments CV7 Panels Connector Layout NXA-AVB/ETHERNET CAT5 NXA-AVB/ETHERNET Specifications Product SpecificationsNXA-AVB/ETHERNET Breakout Box FG2254-10 Rear Components Installing the NXA-AVB/ETHERNETPanels only Audio In Left Channel Wiring the NXA-AVB/ETHERNET connectors and cablesAudio In Right Channel Wiring the NXA-AVB/ETHERNET for Unbalanced Audio PWR Modero Table Top Cable CA2250-50 Wiring the NXA-AVB/ETHERNET for Balanced AudioBalanced OUT Wiring information for the Modero Table Top cable Modero Table Top Cable SpecificationsMaximum Table Top Cable Lengths for Modero Panels Modero Table Top Cable Wiring Table Wire Connector NXA-WC80211B/CF 802.11b Wireless Card FG2255-03 Specifications for NXA-WC80211B/CF Installation of the Wireless Card Table Top Panel Removing the NXT Outer Housing Do not Remove these screws Removal of the outer housing and wireless card location Slot Card Removal Grooves Card removal grooves Removing/installing a compact flash card Closing and Securing the NXT Enclosure Installation of the Wireless Card WallMount Panel Removing the existing NXD Outer Housing Installing the Upgrade Components NXD Replacing and Securing the NXD Enclosure Optional Compact Flash Upgrades NXT-BP Power Pack FG2255-10NXA-CFSP Compact Flash Specifications for the NXA-BASE/1 NXA-BASE/1 Battery Base Kit FG2255-05KSpecifications for the NXT-BP Power Voltage Checking the NXT-BP charge Installing an NXT-BP into the NXA-BASE/1Front Battery not shown For illustration purposes Front Installing the NXA-BASE/1 below an NXT-CV7 PanelBack NXT-CHG Battery Charger Kit FG2255-50K Charging the NXT-BP using the NXA-BASE/1 Powering the NXT-CHG Specifications for NXT-BP and NXT-CHGReading the NXT-CHG LED Indicator Recalibrating the batteries Charging the NXT-BP batteries using the NXT-CHGGreen Solid CV7 Touch Panel Accessories Installing the No-Button Trim Ring Installing the Internal ComponentsUnpacking the Panel Removing the default Button Trim Ring Installing the Button Trim Ring Inserting the No-Button Trim Ring Removing the No-Button Trim Ring Pre-Wall Installation of the Conduit Box CB-TP7 conduit box components Installation of an NXD Touch Panel Installing the NXD panel within a Conduit Box Installing the NXD into drywall using Expansion Clips NXD-CV7 Wall Mount panel dimensions using expansion clips Installation Installing the NXD into a Flat Surface using #4 screws Along the edges Installation Preparing captive wires Wiring Guidelines for the CV7 PanelsUsing the PSN NetLinx connector for power Ethernet RJ-45 Pinouts and Signals Audio/Video RJ-45 Connections and WiringEthernet 10/100 Base-T RJ-45 Connections and Wiring Audio/Video RJ-45 Pinout Information Connecting and Using USB Input Devices RJ-45 wiring diagram Installation Calibrating the Modero Panel Second press/hold Testing your Calibration Touch Panel Calibration Screens Configuring Communication Modero Setup and System Connection Protected Setup Setup the Panel and PC for USB Communication Configuring and Using USB with a Virtual MasterConfirm the Installation of the USB Driver on the PC USB System Connection page using a USB Connection Type Installed prior to setting up a USB connection to the panel Confirm and View the current AMX USB device connections Device Manager dialog showing USB device Before beginning Confirm and View the current AMX USB device connections IP Routing Secondary Connection Page Wireless Access OverviewHot Swapping Configuring Communication Configure the Panel’s Wireless IP Settings Configuring a Wireless Network AccessWireless communication using a Dhcp Address Wireless communication using a Static IP Address Configure the Card’s Wireless Security Settings Following sections use an NXA-WAP200G and the target WAP Procedures Secondary Connection page Wireless Settings section These WEP Key identifier values must match for both devices WEP Key # Keyboard Configuring a Wired Ethernet Connection Configure the Panel’s Wired IP Settings Configuring Communication Choose a Master Connection Mode Setting Configure an Ethernet Connection Type Obtained From NetLinx Master These must match Configuring Communication URL List dialog Using G4 Web Control to Interact with a G4 Panel G4 Web Control Accessing the NetLinx Master via an IP Address Using your NetLinx Master to Control the G4 panel Web Control VNC installation and Password entry screens Connection Details dialog Configuring Communication Configure the panel for a USB Connection Type Upgrading the Modero Firmware via the USB port Prepare NetLinx Studio for communication via the USB port Confirm and Upgrade the firmware via the USB port Default Modero panel value is Select the panel’s KIT file from the Files section Upgrading the Modero Firmware via Ethernet IP Address Prepare the Master for communication via an IP Assigning Communication Settings and TCP/IP Settings Prepare the panel for communication via an IP Verify and Upgrade the panel firmware via an IP Select the panel’s KIT file from the Files section FIG Device and System values Setup Navigation Buttons Setup Navigation Button Elements Setup Setup Page Elements Connection Status Display/Panel TimeoutTimeout Inactivity Page Flip Project Information Project Information Page Elements Panel Information Panel Information Page Elements Time & Date Setup RAM Time Display fields Time & Date Setup Page ElementsTime Date Refresh/Set Date Display fields Volume Volume Page Elements Default Panel Sounds Protected SetupVideo Adjustment Supported sampling rates for WAV Video Setup Page Elements Low Battery Warning Battery BaseBattery Base Page Elements Charge Status Battery Status fields Reaches a point where it needs to be recalibratedLimit Protected Setup Navigation Buttons Protected Setup Navigation Button Elements Reboot Panel Protected SetupProtected Setup Page Elements Device Number System Recovery Slider G4 Web Control G4 Web Control SettingsG4 Web Control Page Elements Sensor Setup G4 Web Control Timeout Dim Mode Minimum Sensor Setup Page ElementsLight Sensor Wake Panel On Motion Motion SensorSense Panel Password Password SetupPassword Setup Page Elements Change Calibration Secondary Connection Secondary Connection Page Elements Wireless Settings Access Point MACAddress 108 System Connection System Connection Page Elements Full Duplex Master Connection ICSNet is not a supported option on this panel Firmware Pages and Descriptions 112 Commands CommandsButton Assignments Sendcommand Panel,@PDR-Popup11 Sendcommand Panel,@DPG-Popup1Group1@PDR-popup page namereset flag Sendcommand Panel,@PHE-Popup1Slide to Left Commands Sendcommand Panel,@PPN-Popup1Main Sendcommand Panel,@PPM-Popup1ModalSendcommand Panel,@PPM-Popup11 Sendcommand Panel,@PPN-Popup1 Sendcommand Panel,@PST-Popup150 Sendcommand Panel,@PSE-Popup1Slide from LeftSendcommand Panel,@PSP-Popup1100,0 Sendcommand Panel,PAGE-Page1 Sendcommand Panel,PPOG-Popup1Main Sendcommand Panel,PPOF-Popup1MainSendcommand Panel,PPOF-Popup1 Sendcommand Panel,PPOG-Popup1 RGB Values for all 88 Basic Colors Programming NumbersRGB triplets and names for basic 88 colors Index No Name Red Green Blue 120 Font ID # Font type Size Default Font Styles and ID NumbersFont styles and ID numbers Variable Fonts start at TPD4 Border Styles by Name Border styles and Programming numbersBorder Styles and Programming Numbers Border styles Modero Widescreen Touch Panels 123 Button Commands Button Commands Sendcommand Panel,BCF-500.504&510.515,1,Yellow Sendcommand Panel,BCB-500.504&510,1,12Sendcommand Panel,BCF-500.504&510.515,1,12 Sendcommand Panel,BCF-500.504&510.515,1,#F4EC0A63 Button Commands Sendcommand Panel,BFB-500,Momentary BIM-vt addr range,input mask Sendcommand Panel,BIM-500,AAAAAAAAAASendcommand Panel,BLN-500,55 BLN-vt addr range,button states range,number Sendcommand Panel,BMC- 150,1,1,315,1,%BR%FT%TX%BM%IC%CF%CT BMC BMF-vt addr range,button states range,data BMF Modero Widescreen Touch Panels 131 Sendcommand Panel,BMP-500.504&510.515,1,bitmap.png Sendcommand Panel,BMI-530,1&2,newMac.pngSendcommand Panel,BML-500,20 BNC-vt addr range,command value Sendcommand Panel,BOP-500.504&510.515,1,200 Sendcommand Panel,BNN-973,192.168.169.99Sendcommand Panel,BNT-973,5000 Sendcommand Panel,BOP-500.504&510.515,1,#C8 Sendcommand Panel,BOS-500,1,1 Sendcommand Panel,BOR-500.504&510.515,10Sendcommand Panel,BOR-500.504&510,AMX Elite -M Sendcommand Panel,BPP-500,1 Sendcommand Panel,BSM-500 Sendcommand Panel,BRD-500.504&510.515,1&2,Quad LineSendcommand Panel,BSF-500,1 Sendcommand Panel,BSO-500,1&2,music.wav BVP-vt addr range,network password Sendcommand Panel,BVL-500,0Sendcommand Panel,BVN-500,191.191.191.191 Sendcommand Panel,BVP-500,PCLOCK ENA-vt addr range,command value Sendcommand Panel,CPF-500Send Command Panel,DPF-409,Prev Sendcommand Panel,ENA-500.504&510.515,0 Sendcommand Panel,GLH-500,1000 Sendcommand Panel,GDI-7,128Sendcommand Panel,GIV-500,3 Sendcommand Panel,GLL-500,150 Sendcommand Panel,GSC-500,12 Sendcommand Panel,GRD-500,200Sendcommand Panel,GRU-500,100 Sendcommand Panel,GSN-500,Ball Sendcommand Panel,JSI-500.504&510.515,1&2,1 Sendcommand Panel,ICO-500.504&510.515,1&2,1Sendcommand Panel,JSB-500.504&510.515,1&2,1 ICO-vt addr range,button states range,icon Send Command Panel,MDC Sendcommand Panel,JST-500.504&510.515,1&2,1Send Command Panel,MBT-1 SHO-vt addr range,command value Sendcommand Panel,TXT-500.504&510.515,1&2,Test Only Sendcommand Panel,TEC-500.504&510.515,1&2,12Sendcommand Panel,TEF-500.504&510.515,1&2,Soft Drop TEC-vt addr range,button states range,color UNI-vt addr range,button states range,unicode text Sendcommand Panel,UNI-500,1,0041Sendcommand TP,UNI-1,0,0041 UNI Text Effect Names Text Effects Button Query Commands Defineevent Custom Event Fields Button Query CommandsSend Command Panel,?BCB-529,1 ?BCB-vt addr range,button states range Get the current fill ?BCF-vt addr range,button states range Send Command Panel,?BCF-529,1Send Command Panel,?BCT-529,1 ?BCT-vt addr range,button states range ?BMP-vt addr range,button states range Send Command Panel,?BMP-529,1Send Command Panel,?BOP-529,1 ?BOP-vt addr range,button states range ?BRD-vt addr range,button states range Send Command Panel,?BRD-529,1Send Command Panel,?BWW-529,1 ?BWW-vt addr range,button states range ?FON-vt addr range,button states range Send Command Panel,?FON-529,1Send Command Panel,?ICO-529,1&2 ?ICO-vt addr range,button states range ?JSB-vt addr range,button states range Send Command Panel,?JSB-529,1Send Command Panel,?JSI-529,1 ?JSI-vt addr range,button states range ?JST-vt addr range,button states range Send Command Panel,?JST-529,1Send Command Panel,?TEC-529,1 ?TEC-vt addr range,button states range ?TEF-vt addr range,button states range Send Command Panel,?TEF-529,1Send Command Panel,?TXT-529,1 ?TXT-vt addr range,button states range,optional Panel Runtime Operation Commands Panel Runtime Operations Send Command Panel,BEEP Send Command Panel,@AKP-12345678ENTER PasswordSend Command Panel,@AKR Send Command Panel,BRIT-50 Send Command Panel,@PKP-1234567ENTER Password Send Command Panel,@EKP-33333333Enter PasswordSend Command Panel,PKEYP-123456789 Send Command Panel,SETUP Send Command Panel,TPAGEON Send Command Panel,@SOU-Music.wavSend Command Panel,@TKP-999.222.1211Enter Phone Send Command Panel,TPAGEOFF Input Commands Input Commands Embedded Codes Embedded codesDecimal numbers Hexidecimal values Virtual keystroke Panel Setup Commands Panel Setup Commands Dynamic Image Commands Dynamic Image Commands RAF-resource name,data Embedded Codes Parameter Description Troubleshooting Information My NXT-BP battery pack is Symptom Solution Updated my panel firmware butMy Battery Base page doesn’t Life indicator Was using the power from Symptom SolutionConnecting NXA-BASE/1 battery base to NXA-BASE/1 connected to a My battery from within anPowered panel My WEP doesn’t seem to be Connected to my System Master After downloading a panel file or Symptoms includeProviding power Only one shows up Troubleshooting 168 Formatting Code Operations Text Formatting Codes for Bargraphs/JoysticksBargraph Text Code Inputs Example Character Types Text Area Input MaskingInput mask character types Character Masking Rule Input mask operations Input mask rangesInput mask next field characters Input mask literals Output Examples Input mask output examplesCommon Name Input Mask Escape Sequences URL ResourcesSpecial escape sequences Sequence Panel Information 174 Appendix Widescreen Modero Touch Panels 175 RevisionLast15/08/04