Chapter 2 Alarm Troubleshooting

2.7.199 SD-L

Note The recommended test set for use on all SONET ONS electrical ports is the Omniber 718.

Clear the SD (DS1, DS3) Condition

Step 1 Complete the “Clear a DS-3 or DS-1 Port Loopback Circuit” procedure on page 2-156.

Caution Always use the supplied electrostatic discharge wristband when working with a powered ONS 15310-CL or ONS 15310-MA.

Step 2 Ensure that the fiber connector for the port is completely plugged in. For more information about cable connections, refer to the “Install Hardware” chapter in the Cisco ONS 15310-CL and

Cisco ONS 15310-MA Procedure Guide.

Step 3 If the BER threshold is correct and at the expected level, use a test set to measure the power level of the line to ensure it is within guidelines. For specific procedures to use the test set equipment, consult the manufacturer.

Step 4 If the power level is good, verify that receive levels are within the acceptable range. The correct specifications are listed in the “Install Hardware” chapter in the Cisco ONS 15310-CL and Cisco ONS 15310-MA Procedure Guide.

Step 5 If receive levels are good, clean the fibers at both ends according to site practice. If no site practice exists, complete the procedure in the “Maintain the Node” chapter in the Cisco ONS 15310-CL and

Cisco ONS 15310-MA Procedure Guide.

Step 6 If the condition does not clear, verify that single-mode fiber is used.

Step 7 If the fiber is of the correct type, verify that a single-mode laser is used at the far-end node.

Step 8 Clean the fiber connectors at both ends for a signal degrade according to site practice. If no practice exists, use the procedure in the “Maintain the Node” chapter in the Cisco ONS 15310-CL and Cisco ONS 15310-MA Procedure Guide.

Step 9 If the problem does not clear, the transmitter at the other end of the optical line could be failing and require replacement.

Step 10 If the condition does not clear, log into the Technical Support Website at http://www.cisco.com/techsupport for more information or call Cisco TAC (1-800-553-2447).

2.7.199 SD-L

Default Severity: Not Alarmed (NA), Non-Service-Affecting (NSA)

SONET Logical Objects: EC1, OCN

An SD Line condition applies to the line level of the SONET signal and travels on the B2 byte of the SONET overhead for a 15310-CL-CTX, DS1-28/DS3-EC1-3, or DS1-84/DS3-EC1-3 EC1 signal, or a for a 15310-CL-CTX or CTX2500 card. An SD-L condition on an Ethernet card or OC-3 port does not cause a protection switch. If the condition is reported on a port that has also undergone a protection switch, the SD BER count continues to accumulate. The condition is superseded by higher-priority alarms such as 2.7.135 LOF (OCN) or 2.7.150 LOS (OCN).

Cisco ONS 15310-CL and Cisco ONS 15310-MA Troubleshooting Guide, R7.0

2-123

Page 232 Page 234
Page 233
Image 233
Cisco Systems ONS 15310-MA, ONS 15310-CL manual Sd-L, Clear the SD DS1, DS3 Condition, 123
Page 232 Page 234

ONS 15310-CL, ONS 15310-MA specifications

Cisco Systems has long been a leader in networking and telecommunications technology, and among its impressive lineup of products, the Cisco ONS 15310 series stands out as an essential solution for optical networking. This series includes models such as the ONS 15310-MA, ONS 15310-CL, and ONS 15310-CA, each designed to meet the diverse needs of service providers and enterprises seeking to enhance their optical transport networks.

The Cisco ONS 15310-MA is an advanced multi-service platform designed for metropolitan area networks. It facilitates the seamless transport of data, voice, and video over optical networks. One of its main features is its ability to support a variety of interfaces, including Ethernet, SONET/SDH, and Wavelength Division Multiplexing (WDM), allowing users to integrate multiple services into a single platform. Additionally, the ONS 15310-MA supports advanced traffic management and Quality of Service (QoS) features to prioritize critical applications and ensure consistent performance.

The ONS 15310-CL variant is tailored for more specific applications, providing enhanced capabilities aimed at delivering carrier-grade services. It features a robust architecture that accommodates high-capacity traffic without compromising reliability. This model emphasizes low power consumption and a compact design, making it suitable for deployment in space-constrained environments. The ONS 15310-CL also supports a wide range of optical interfaces, making it highly flexible for various network configurations.

In terms of technologies, the Cisco ONS 15310 series leverages Optical Transport Network (OTN) capabilities, providing high efficiency and greater bandwidth utilization. OTN technology enables efficient error correction and adds resilience to the network through its built-in protection mechanisms. Furthermore, the series supports seamless integration with existing IP/MPLS networks, creating a cohesive infrastructure as organizations evolve their networking requirements.

One of the defining characteristics of the ONS 15310 series is its focus on scalability. Network operators can start with a modest deployment and gradually expand capacity as demand grows. This adaptability is complemented by Cisco's comprehensive management and monitoring tools, providing operators with real-time insights into network performance and facilitating proactive management.

In conclusion, the Cisco ONS 15310-MA and ONS 15310-CL models represent sophisticated solutions for modern optical networks. With their versatile features, advanced technologies, and robust design, they empower service providers and enterprises to build resilient, high-capacity networks that meet the demands of today’s data-driven world.
Top Page Image Contents