Chapter 4 Error Messages

Table 4-1

Error Messages (continued)

 

 

 

 

Error Warning

 

 

ID

Error Warning Message

Description

 

 

 

EID-4011

Provisioning error:

Refer to the error message text.

 

{0}

 

 

 

 

EID-5000

Cannot find a valid route for tunnel change request.

Refer to the error message text.

 

 

 

EID-5001

Tunnel could not be changed.

Refer to the error message text.

 

 

 

EID-5002

Tunnel could not be restored and must be recreated manually.

Refer to the error message text.

 

 

 

EID-5003

Circuit roll failure.

Refer to the error message text.

 

{0}

 

 

 

 

EID-5004

There is already one 4F {0} provisioned on the set of nodes

There is already one 4F BLSR provisioned

 

involved in {1}. The maximum number of 4F {0} rings has

on the set of nodes involved in the ring. The

 

been reached for that node.

maximum number of 4F BLSR rings has

 

 

been reached for that node.

 

 

 

WID-5005

A non-zero hold-off time can violate switching time standards,

Refer to the warning message text.

 

and should only be used for a circuit with multiple path

 

 

selectors.

 

 

 

 

WID-5006

Warning: Different secondary {0} node should only be used for

You should use different secondary end

 

DRI or Open-ended path protected circuits.

point only for DRI or open-ended path

 

 

protected circuits.

 

 

 

WID-5007

If you change the scope of this view, the contents of this profile

Refer to the warning message text.

 

editor will be lost.

 

 

 

 

WID-5008

Please make sure all the protection groups are in proper state

Refer to the warning message text.

 

after the cancellation.

 

 

 

 

WID-5009

Circuit {0} not upgradable. No {1} capable {2}s are available

No VT capable STSs are available at the

 

at node {3}.

node.

 

 

 

EID-5010

Domain name already exists.

Refer to the error message text.

 

 

 

EID-5011

Domain name may not exceed {0} characters.

You may have reached the maximum

 

 

number of charcters.

 

 

 

WID-5012

Software load on {0} does not support the addition of a node to

Refer to the warning message text.

 

a 1+1protection group.

 

 

 

 

EID-5013

{0} doesn’t support Bridge and Roll Feature. Please select a

The specified port does not support Bridge

 

different port.

and Roll.

 

 

 

EID-5014

An automatic network layout is already in progress, please wait

You must for the automatic network layout

 

for it to complete for running it again.

to complete before running it again.

 

 

 

WID-5015

{0} cannot be applied to {1}.

You cannot apply the admin state operation,

 

 

specified by {0}, to port count, specified by

 

 

{1}.

 

 

 

EID-5016

An error was encountered while attempting to provision the

CTC encountered an error while

 

{0}. {1}

provisioning the card.

 

 

 

EID-5017

Unable to rollback provisioning, the {0} may be left in an

You may have to remove the BLSR

 

INCOMPLETE state and should be manually removed.

manually as it was left incomplete.

 

 

 

Cisco ONS 15310-CL and Cisco ONS 15310-MA Troubleshooting Guide, R7.0

4-32

Page 309 Page 311
Page 310
Image 310
Cisco Systems ONS 15310-CL, ONS 15310-MA manual Error Warning Message Description
Page 309 Page 311

ONS 15310-CL, ONS 15310-MA specifications

Cisco Systems has long been a leader in networking and telecommunications technology, and among its impressive lineup of products, the Cisco ONS 15310 series stands out as an essential solution for optical networking. This series includes models such as the ONS 15310-MA, ONS 15310-CL, and ONS 15310-CA, each designed to meet the diverse needs of service providers and enterprises seeking to enhance their optical transport networks.

The Cisco ONS 15310-MA is an advanced multi-service platform designed for metropolitan area networks. It facilitates the seamless transport of data, voice, and video over optical networks. One of its main features is its ability to support a variety of interfaces, including Ethernet, SONET/SDH, and Wavelength Division Multiplexing (WDM), allowing users to integrate multiple services into a single platform. Additionally, the ONS 15310-MA supports advanced traffic management and Quality of Service (QoS) features to prioritize critical applications and ensure consistent performance.

The ONS 15310-CL variant is tailored for more specific applications, providing enhanced capabilities aimed at delivering carrier-grade services. It features a robust architecture that accommodates high-capacity traffic without compromising reliability. This model emphasizes low power consumption and a compact design, making it suitable for deployment in space-constrained environments. The ONS 15310-CL also supports a wide range of optical interfaces, making it highly flexible for various network configurations.

In terms of technologies, the Cisco ONS 15310 series leverages Optical Transport Network (OTN) capabilities, providing high efficiency and greater bandwidth utilization. OTN technology enables efficient error correction and adds resilience to the network through its built-in protection mechanisms. Furthermore, the series supports seamless integration with existing IP/MPLS networks, creating a cohesive infrastructure as organizations evolve their networking requirements.

One of the defining characteristics of the ONS 15310 series is its focus on scalability. Network operators can start with a modest deployment and gradually expand capacity as demand grows. This adaptability is complemented by Cisco's comprehensive management and monitoring tools, providing operators with real-time insights into network performance and facilitating proactive management.

In conclusion, the Cisco ONS 15310-MA and ONS 15310-CL models represent sophisticated solutions for modern optical networks. With their versatile features, advanced technologies, and robust design, they empower service providers and enterprises to build resilient, high-capacity networks that meet the demands of today’s data-driven world.
Top Page Image Contents