Eaton Electrical ASY0529, ASY0567, ASY0673, ASY0674 - page 64

ISOLATED OUTPUT WIRING DIAGRAMS

Eaton 9170+ UPS (3–18 kVA) User's Guide S 164201393 Rev E www.eaton.com/powerquality

58

S100/200 Input, 100/200 Output

S120/208 Input, 120/240 Output

S110/220 Input, 110/220 Output

S115/230 Input, 115/230 Output

S120/240 Input, 120/240 Output

14

3

4

7

9

9

6

8

Figure 39. No External Bypass (L1, L2, N), Isolated Output for Single-Phase VoltagesNOTE To use Figure 39, refer to the list of Notes on page 56.

Contents

Main Requesting a Declaration of Conformity Class A EMC Statements Special Symbols Table of Contents Page Chapter 1 Introduction Safety Warnings IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS S Consignes de Scurit CONSIGNES DE SCURIT IMPORTANTES CONSERVER CES INSTRUCTIONS A T T E N T I O N ! S Advertencias de Seguridad INSTRUCCIONES DE SEGURIDAD IMPORTANTES GUARDE ESTAS INSTRUCCIONES P R E C A U C I N S Physical Features Page Figure 4. Nine-Slot Cabinet (Rear View) Figure 5. Power Module (ASY-0673 and ASY-0674) Figure 6. Battery Module (ASY-0529) Page Chapter 2 Installation Setup Equipment Clearances Location Requirements UPS Setup Three- and Six-Slot Cabinets Nine- and Twelve-Slot Cabinets Caster Cart Installation (Three- and Six-Slot Cabinets) Stabilizer Bracket Installation (Twelve-Slot Cabinet Only) Rack-Mount Installation (Three- and Six-Slot Cabinets) Page Floor Anchor Kit Installation Moving the Cabinets Page Chapter 3 UPS with Bypass Electrical Installation Figure 12. Typical Installation with a Bypass Switch Input Current Ratings Bypass Switches Bypass Switch Operation S Page Table 4. Bypass Switch Specifications Figure 13. Bypass Switch Dimensions UPS Installation with an External Bypass Switch Figure 14. UPS Power Entrance Panel (Nine-Slot Cabinet Shown) 5. Remove the knockouts in the entrance panel for AC input and AC output wiring. Page Page Page 12. Unscrew and remove the top rear cover of the cabinet and locate the terminal block. Page Page Select wiring diagrams from Table 5 based upon the installation voltage. Table 5. UPS with Bypass Wiring Diagrams The following notes are referenced in the system wiring diagrams (Figure 22 through Figure 24). Page Page Page Chapter 4 UPS Electrical Installation Input Current Ratings See Table 7 for recommended conductor sizes to wire the input circuit breakers. Table 7. Recommended Wire Sizes UPS Electrical Installation Page Page Page Page Page Select wiring diagrams from Table 8 based upon the installation voltage. Table 8. Wiring Diagrams Page Page Page Page Chapter 5 Isolated Output Wiring Diagrams NOTE This chapter is only for units manufactured before 2009. Neutral-to-Ground Bonding for Isolated Output Page Page Page Page ISOLATED OUTPUT WIRING DIAGRAMS (Voltages require the bypass switch to be BBM; contact your service representative for details.) Eaton 9170+ UPS (318 kVA) User's Guide S 164201393 Rev E www.eaton.com/powerquality 59 S120/208 Input, 120/208 Output S127/220 Input, 127/220 Output ISOLATED OUTPUT WIRING DIAGRAMS 60 Eaton 9170+ UPS (318 kVA) User's Guide S 164201393 Rev E www.eaton.com/powerquality S120/208 Input, 120/208 Output S127/220 Input, 127/220 Output Chapter 6 Battery Cabinet Installation S Page Page Page + Page Chapter 7 UPS Startup S Power and Battery Module Installation Page Startup for Plug-Receptacle Units Page Startup for Hardwired Units Page Page Initial Startup Parameters ENTER PASSWORD Password 0000 < > ESC Set Time time 14:51:38 < > ESC External Capacity extamphr 0028.8 < > ESC Page Chapter 8 Operation Page Turning the UPS On Removing Input Power Front Panel Display 1 2 9 USER #3 Wout watts 2.07 KW Figure 54. UPS Front Panel Table 10. Front Panel Details Using the Front Panel Display 1 2 9 USER #2 Wout watts 1.87 KW S Page Parameters Changing Parameter Settings Reading the Eaton 9170+ System Logs Inverter Log 2 1 1 #0 I 09/29 13:56 01:04 Line Fault Alarm Log Battery Test Menu Map OPERATION Figure 60. Eaton 9170+ System Menu Map Chapter 9 Communication S S S S S Power Management and Protection Software Optional Interface Kits Communication Slots Dedicated Input Signals S DB-9 Communication Port Table 13. DB-9 Port Signals Chapter 10 Maintenance Routine Maintenance Storage Temperature External Bypass Switch (Make-Before-Break Only) Operation S Battery Replacement Power Module Replacement Page Chapter 11 Specifications This section provides the following specifications for the Eaton 9170+ models: S S S S S Table 14. Electrical Input and Output Table 15. Application of Neutral to Ground Bonding Table 16. Model Specifications for Split-Phase Power Modules (ASY-0673) Page Table 16. Model Specifications for Split-Phase Power Modules (ASY-0673) (continued) Table 17. Model Specifications for Universal Power Modules (XXXXX-Model/03 and ASY-0674) Page Table 17. Model Specifications for Universal Power Modules (XXXXX-Model/03 and ASY-0674) (continued) Table 18. Environmental and Safety Table 19. Battery Table 20. Weights and Dimensions Page Chapter 12 Troubleshooting The following table provides answers to commonly asked questions. Table 21. Frequently Asked Questions Page Alarms S High AC Input System M Batt Test Failed 1 Open Cell Slot 4 S S S When an alarm occurs, follow these steps: 1. Observe the display to see which alarm is active. Table 22. Critical Alarm Messages Page Table 23. Non-Critical Alarm Messages Service and Support Page Chapter 13 Warranty Two-Year Limited Warranty (US and Canada) Eaton UPS Models: 9155, 9170+ and FERRUPS 4.318 kVA WARRANTOR: LIMITED WARRANTY: Page OTHER LIMITATIONS: COSTS NOT RELATED TO WARRANTY: OBTAINING WARRANTY SERVICE: Load Protection Guarantee (US and Canada) GUARANTOR: LIMITED GUARANTY: WHAT THIS GUARANTY COVERS: *Cumulative Limits to be paid by Guarantor under this Load Protection Guaranty: