Fostex VF160EX operation manual Pair Fader setting Pair Fader Set, 146

Pair Fader setting [Pair Fader Set]

The “Pair Fader Set” menu sets whether or not you simultaneously control the adjacent odd and even chan- nels.

Normally, each channel fader on the VF160EX acts independently. By setting "Pair Fader Set" to "On", you can pair faders of two adjacent channels, allowing the odd channel fader to control the partner (even) channel's level. This function is useful for stereo source, etc.

You can also control "Pair Fader channels" simultaneously during channel parameter editing, etc. See <Hint!> below.

• Initial setting:	"Off" for all pair channels
• Options:	"On", "Off" for each pair
	channels

*You can set the value for each Program individually.

*The settings can be saved and loaded as part of the song data.

*The settings are maintained after you turn off the power to the VF160EX.

1.Select “Pair Fader Set” in the menu selection display and press the [ENTER/YES] key.

The pair fader set status (on or off) list is shown, where the channel 1 & 2 line is highlighted. In the initial condition, all paired channels are set to "Off".

Flashing

2.Select the desired paired channels via the [JOG] dial, and press the [ENTER/YES] key.

The setting field ("On" or "Off" is shown) for the selected channels flashes.

3.Select "On" or "Off via the [JOG] dial, and press the [ENTER/YES] key.

The setting is completed and the display returns to highlight a single line, as shown in step 1 above.

4.To set another pair, repeat steps 2 and 3.

5.After completing all settings, press the [EXIT/NO] key (or the [STOP] key) to exit the SETUP mode.

<Note>

If you control the even channel fader which is paired, the following message appears.

Controlling the paired even channel fader does not affect the level.

<Hints!>

For paired fader channels, besides fader control, the following functions are controlled simulta- neously.

• Effect send level adjustment

By pressing either of the [CH STATUS/CH SEL] keys for paired channels, the icons for both channels start flash- ing, and you can control the effect send levels for both channels simultaneously using the [JOG] dial.

• Effect send pre/post setting

By pressing either of the [CH STATUS/CH SEL] keys for paired channels, the icons for both channels start flash- ing, and you can set pre or post for the effect sends of both channels simultaneously using the [JOG] dial.

• Aux send level adjustment

By pressing either of the [CH STATUS/CH SEL] keys for paired channels, the icons for both channels start flash- ing, and you can control the Aux send levels for both channels simultaneously using the [JOG] dial.

• Aux send pre/post setting

By pressing either of the [CH STATUS/CH SEL] keys for paired channels, the icons for both channels start flash- ing, and you can set pre or post for the Aux sends of both channels simultaneously using the [JOG] dial.

• EQ (HI/MID/LO) adjustment

By pressing either of the [CH STATUS/CH SEL] keys for paired channels, the icons for both channels start flash- ing, and you can adjust EQ for both channels simulta- neously.

• On/off of SOLO

By pressing either of the [CH STATUS/CH SEL] keys for paired channels, you can select on or off of solo monitor for both channels simultaneously.

• On/off of channel mute

By pressing either of the [CH STATUS/CH SEL] keys for paired channels, you can select on or off of mute for both channels simultaneously.

•Setting of INPUT (TRACK/INPUT) SEL (channels 9 through 16 only)

By pressing either of the [CH STATUS/CH SEL] keys for paired channels, you can select the input sources for both channels simultaneously.

•Setting of REC source for BUSS recording

By pressing either of the [CH STATUS/CH SEL] keys for paired channels, you can select the REC sources for both channels simultaneously.

• Setting of the built-in compressor

By pressing either of the [CH STATUS/CH SEL] keys for paired channels (channels 13-14 or 15-16), you can set the compressor parameters for both channels simulta- neously.

146