Channel Parameter Edit

You can edit the various parameter settings such as pan and equalizers for channels 1 through 16 and the master channel. We refer this type of editing as "Channel parameter edit". There are several channel parameter edit keys on the top panel (as shown below) and pressing the dedicated key for the parameter you want to edit brings up the corresponding edit screen. Some keys also handle the second parameter (labeled under the key) and you can bring up the corresponding edit screen by pressing the key while holding down the [SHIFT] key. You can view and/or edit the following parameters.

Pan setting

3-band equalizer setting

Effect send level setting

Pre/post selection of the effect send

Aux (auxiliary) send level setting

Pre/post selection of the Aux (auxiliary) send

Compressor setting

Fader level setting

Channel view (viewing only)

EQ/COMP

EFF1/EFF2HI-G/F/Q

PRE/POST

 

COMP

AUX1/AUX2MID-G/F/Q

PRE/POST

PANLO-G

FADER

 

CH VIEW

CH PARAM EDIT

<Caution>

If you must edit channel param- eters such as setup of PAN or EQ, be sure to check that the "Scene Sequence Mode", explained later, is switched "Off". Should the pa- rameters be edited with this "Scene Sequence Mode" switched "On", the parameters will be re- turned to their original setting when VF160EX is operated in PLAY or STOP. Refer to page 66 for "On/off of the Scene Sequence

Mode".

<Hints>

2. Press the [CH STATUS/CH SEL] key of the desired

channel.

If a channel whose source is set to INPUT via the IN-

The current settings are shown, together with the selected

PUT SEL setting is selected as the edit channel, the

channel name. The icon for the selected channel is flash-

channel name is shown as below.

ing, indicating that you can edit it.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

In the following example, channel 9 which is set to

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INPUT, is selected as the edit channel.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Flashing

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Flashing

Lighting

Flashing

Adjusting Pan

You can adjust the pan (or balance) of each input chan- nel signal fed to the stereo outputs, as well as fed to the Rec buss outputs. The panpot for master channel con- trols the L/R level balance of the stereo outputs.

1.Press the [PAN] key.

All channel settings are shown on the screen.

The first time you bring up the channel parameter edit screen, the message prompting to select a channel ("Select CH!") flashes, as well as all the CH STATUS/CH SEL indicators on the panel flash.

From the second time on, the previously selected channel is selected and ready to be edited when bringing up the screen (as shown in the drawing of step 2 below).

Flashing

3.Use the [JOG] dial to adjust panning.

Rotating the [JOG] dial to the left or right moves the pan position to the left or right respectively.

The following show examples of the pan settings.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pan position:

Pan position:

Pan position:

center

hard left

hard right

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

•Controllable channels

Channels 1 through 16 and the master channel

•Available values

L10 (hard left) through C (center) to R10 (hard right) (the default setting: "C" for all channels)

*Values are displayed between L10 and R10 in 21 steps but the actual pan setting is changed smoothly and continuously as rotating the [JOG] dial.

4.To set another channel's pan, repeat steps 2 and 3 above.

5.After completing pan editing, press the [EXIT/NO] key.

The VF160EX exits the channel edit mode and the display returns to the Normal display.

50

Page 50
Image 50
Fostex VF160EX operation manual Channel Parameter Edit, Adjusting Pan, Hints