< Note >

When you press the [ENTER/YES] key to finalize the ef- fect type, the sound will be muted for an instant.

Effect parameter settings

Here's how to set the effect parameters.

1.If the effect parameter that you wish to adjust is not displayed, press the [EFF 1] key (or the [EFF 2] key) twice.

One of the parameters of that effect type will appear.

Flashing

2.Press the [EFF 1] key (or the [EFF 2] key) several times to display the desired parameter.

The parameters that appear will differ, depending on the effect type that is selected.

Flashing

3.Use the [JOG] dial to adjust the value.

For details on the meaning and range of eachparameter, refer to "Effect parameter details" on the below.

4.If you wish to adjust another parameter, repeat from <step 2>.

5.When you are finished making settings, press the [EXIT/NO] key twice to exit Effect Edit mode.

Muting an effect

You can mute the effect sound of effect 1 or effect 2.

•To mute the effect sound:

Hold down the [SHIFT] key and press the [EFF 1] key (or [EFF 2] key).

The effect sound of effect 1 (or effect 2) will be muted, and the dry sound will be heard.

When muting is on, the [EFF 1] key (or [EFF 2] key) LED is off.

•To cancel muting:

Once again hold down the [SHIFT] key and press the [EFF 1] key (or [EFF 2] key).

The dry sound will change back to the effect sound. When mute is turned off, the [EFF 1] key (or [EFF 2] key) LED is off.

Effect parameter details

The parameters that can be adjusted will depend on the parameter type.

Reverb effect parameters (parameter type: REVERB)

For effect types 1--24of the preceding "Effect type" table, the following four parameters can be adjusted.

1.Eff Level

Adjust the effect return level: 0~99

2.Rev Time

Adjust the length of reverberation. Range: 0.1--9.9 seconds

3.Pre Delay

Adjust the time from the original sound until reverberation begins. Range: 0--100 ms

4.Hi Ratio

Adjust the decay ratio of the high frequencies. Range: 0--10

5.E/R Level

Adjust the volume of the early reflections. Range: 0--99

Delay+reverb effect parameters (parameter type: DELAY+REVERB)

For effect types 25--28of the preceding "Effect type" table, the following four parameters can be adjusted.

1.Eff Level

Adjust the effect return level: 0~99

2.Delay Time

Adjust the delay time: Range: 1--230 ms

3.Feedback

Adjust the number of delay repeats. Range: 0--99

4.Delay Bal

Adjust the delay balance. Range: 0--99

5.Rev Time

Adjust the length of reverberation. Range: 0.1--9.9 seconds

Delay effect parameters (parameter type: DELAY)

For effect types 29 and 30 of the preceding "Effect type" table, the following four parameters can be adjusted.

1.Eff Level

Adjust the effect return level: 0~99

2.Delay Time

Adjust the delay time. Range: 1--680 ms

3.Feedback

Adjust the number of delay repeats. Range: 0--99

4.Hi Ratio

Adjust the decay ratio of the high frequencies. Range: 0--10

5.Filter

Adjust the tone of the delay sound. Range: L9~L1, OFF, H1~H9

 

* L1~L9 = LPF (larger numbers will lower the cutoff frequency)

 

* H1~H9 = HPF (larger numbers will raise the cutoff frequency)

59

Page 59
Image 59
Fostex VF160EX operation manual Effect parameter settings, Muting an effect, To mute the effect sound, To cancel muting