Top Panel

Recorder Section

 

 

25

26 27 28

 

29 30

31

 

34

 

 

 

REC ASSIGN

 

 

 

 

 

36

 

 

 

 

 

 

 

 

 

33

 

 

 

BUSS

DIRECT

INT

 

PGM SEL

 

 

INPUT SEL

SOURCE

REC TRK

REC TRK

DISP SEL

SETUP

32

 

 

 

 

 

MIXDOWN

 

 

 

37

 

 

AUTO RTN

 

 

TIME BASE

 

 

 

35

 

 

AUTO PUNCH

 

 

CLIPBOARD

 

A RTN

 

 

START

IN

OUT

END

IN

ALIGN SEL

OUT

A PLAY

39

 

 

43

1

2

 

3

4

5

6

7

 

 

 

 

 

MARK

 

 

 

SCENE SEQ.

38

 

 

HOLD/

STORE

EDIT

UNDO

 

VARI

LOCATE

SCRUB

40

 

/REDO

 

PITCH

 

 

 

 

 

 

 

 

 

46

41

 

 

 

 

 

 

P.EDIT

EVT MEM

CD PLAY

45

 

 

 

 

 

 

 

 

 

42

 

RECORD

 

STOP

 

PLAY

REWIND

 

F FWD

44

47

 

AUTO

 

CLIPBOARD PLAY

 

PREV

 

NEXT

51

 

PUNCH

 

LOCATE ABS 0

 

 

 

 

48

 

 

 

LOCATE REC END

 

 

 

 

 

 

 

 

 

 

 

 

 

 

50

49

 

 

 

 

 

 

 

 

 

 

FADER

 

 

 

 

 

 

 

 

 

 

ADJUST

 

 

EXIT/NO

 

 

 

 

 

52

54

53

55

25. [INPUT SEL] Key

LEVEL

ADJUST

SHIFT

EJECT

ENTER/YES

56

JOG

SHUTTLE

* The tracks recorded vary, as shown below, according

*Set whether to send the A to H input signals [INPUT] or track 9-16 play [TRACK] sounds to the faders of channel faders 9 to 16.

*When executing DIRECT recording, with the [SHIFT] key pressed down, each time the [INPUT SEL] key is pressed while in the normal display mode, the input monitor (READY) can be switched ON/OFF for all tracks (1-16). However, any track that is setup to [IN] (Input) by the INPUT SEL setting ([IN]-[TRK]) cannot be changed to input monitor.

26. [REC ASSIGN-BUSS-SOURCE] Key

*Select the channel (SOURCE) to send to the REC BUSS during “BUSS” recording. Select the SOURCE channel with the [CH STATUS/CH SEL] key.

*This key lights ON when the SOURCE is selected.

27. [REC ASSIGN-BUSS-REC TRK] Key

*The track (READY) to record in “BUSS” recording is selectable when this key is flashing. Set READY track with the [CH STATUS/CH SEL] Key.

*This key lights ON when the READY track is set for “BUSS” recording.

to the connection jack.

a. Current location of TIME BASE selected

Shows the current location of the sound.

b. REMAINING TIME BASE Selected (time remaining)

Shows the time remaining and space available on the

disk for recordings (in terms of mono track).

c. MTC Time Input

Shows the MTC time input in the [MIDI IN] jack.

This is a convenience for operations as a slave device.

* The user can switch between time bases, as shown

below, by pressing the [DISP SEL/TIME BASE] key,

while the [SHIFT] key is depressed.

a. ABS (Absolute Time) Indication

An absolute time base from 00H 00M 00S (ABS 0) to

24H 00M 00S.

b. BAR/BEAT/CLK (Bar)

The “Bar, Beat, Clock” of the beat and tempo set with

the internal tempo map.

c. MTC (MIDI Time Code)

Display of the MTC time setting.

28. [REC ASSIGN-DIRECT-REC TRK] Key

*The track (READY) record in “DIRECT” recording is selectable when this key is flashing. Set READY track with the [CH STATUS/CH SEL] key.

*This key lights ON when the READY track is set for “DIRECT” recording.

29. [DISP SEL/TIMEBASE] Key

*This key is used to alternate the menu shown on the LCD in the following order.

30. [PGM SEL] Key

*This is used to switch between programs 01 to 99. This is also used to create new programs.

31. [SETUP] Key

*This is used to go into the setup mode to set various parameters of the recorder and mixer.

19

Page 19
Image 19
Fostex VF160EX operation manual Recorder Section