Note that it is not possible to paste to the same track that was copied (or moved) when copying (or moving) multiple tracks (1-3, 5-8, etc.), although it was possible in the cases described earlier. In this case, the track will not be changed even if the [CH STATUS/CH SEL] key is pressed.

7.Turn the [JOG] dial to choose the paste repeat frequency.

The desired number can be input in the “01” area of the “Repeat = 01” that is currently flashing. The maximum repeat frequency that can be input is 99 but this repeat frequency is automatically limited according to how much space is available on the disk. Simply put, a frequency of 99 repeat times can be input if there is enough disk space. If there isn’t, then only the maximum allowable repeat frequency (size) for the remaining disk space can be input. It is not possible to go above this number even if the [JOG] dial is turned.

8.Press the [ENTER/YES] key.

Copy Paste” (or “Move Paste”) flashes on the display. “Please Wait!” flashes while the data is being pasted. “Completed!” lights up when the data has been successfully pasted.

9.Press the [EXIT/NO] key (or [STOP] key).

The system exits from the edit mode and returns to the original time base display.

UNDO/REDO Paste

Copy & Paste or Move & Paste can be undone and redone with the UNDO/REDO feature.

The data pasted can be undone (unpasted) by pressing the [UNDO/REDO] key after Copy & Paste (or Move & Paste). The data will return to the pre-paste status when undone (unpasted).

Data pasted but undone (unpasted) can be redone (re-pasted) by pressing the [UNDO/REDO] key immediately after undoing the paste process. The data will return to the post-paste status when re-done (re-pasted).

Note the following when executing the UNDO/REDO feature.

<Caution>

The UNDO/REDO feature is valid only when the recorder is in the STOP state. UNDO/REDO is no longer possible if the following procedures take place after Copy & Paste (or Move & Paste).

1.When data is newly recorded.

2.When data is newly edited.

3.When the AUTO PUNCH mode is ON and PLAY (or RECORD) mode is effected, and the point has already passed the AUTO PUNCH IN point.

4.When the power is turned OFF.

5.When program selection takes place.

<Caution>

Note that Copy & Paste (or Move & Paste) is not possible unless there is enough disk space to “UNDO/REDO”, as explained in the next section. When attempting to paste to a disk that does not have enough disk space, “OverTime!” appear on the display and the insufficient time appears according to the currently selected time base.

In such case, either shorten the COPY DATA (or MOVE DATA) by the time it is in the excess, or erase unnecessary data or programs from the erase to secure enough disk space. Then repeat the paste procedure.

Refer to the “Erasing a Program” on page 71 for instructions on how to erase a program, in terms of the “ERASE” instructions to erase unnecessary data.

< Please note >

For regular copy & paste (or move & paste) as shown in Figure 1, the CLIPBOARD IN point of the data which was copy clipped (or move clipped) onto the clipboard, is aligned with the AUTO PUNCH IN point and pasted.

 

CLIPBOARD IN

CLIPBOARD OUT

 

 

POINT

POINT

 

 

 

 

 

 

 

 

 

To align the head of the measure for pasting together with sound data in front of the measure, the “ALIGN SEL” function of VF160EX can be utilized. To use this function, the head of the measure data in the clip data must be registered in the [ALIGN SEL] key as shown in Figure 3.

<Actual sound point>

 

CLIPBOARD IN

CLIPBOARD OUT

POINT

POINT

 

ALIGN SEL POINT

 

<Head of the measure>

 

 

<Figure 1>

AUTO PUNCH IN

POINT

Due to this, as shown in Figure 2, in the case whereby data registered in the CLIPBOARD is the actual sound point and head of the measure is behind this, then even though you attempted to paste this head of the measure in alignment with this previously head, it will be pasted off alignment by this procedure due to the CLIPBOARD IN = ALIGN SEL function.

CLIPBOARD IN POINT

 

 

 

 

ALIGN SEL POINT

CLIPBOARD OUT

<Actual sound point>

POINT

 

 

 

<Head of the measure>

 

<Actual sound point>

<Figure 3>

 

<Head of the measure>

 

AUTO PUNCH IN

 

POINT

 

CLIPBOARD IN data, as a result of copy clip (or move clip), will be directly registered in the [ALIGN SEL] key. Next, recall the [ALIGN SEL] key data (press the [ALIGN SEL] key) and, after correcting this data to head point of the measure, press the [STORE] key and then the [ALIGN SEL] key. After this, by executing copy & paste (or move & paste), the aligned heads of the measures together with data in front of the measures, can be pasted.

<Head of the measure>

AUTO PUNCH IN

POINT

<Figure 2>

< Note >

The range in correction of the ALIGN SEL data must be strictly limited between CLIPBOARD IN-OUT.

74

Page 74
Image 74
Fostex VF160EX operation manual UNDO/REDO Paste, Turn the JOG dial to choose the paste repeat frequency, Please note