System Messages | HP UX Internet and Networking Software specification

System Messages

Explanation: A conﬁgurable parameter has been conﬁgured too high or too low to be valid. The parameter is speciﬁed on the line following the message.

Action: Check and correct the parameter speciﬁed in the NET.CFG ﬁle. See Chapter 2, “NET.CFG Options Reference,” for more information.

NETX-1.00-57: DOS is only conﬁgured for <number> drives, NETX.VLM requires 26 drives for full functionality. The NETX.VLM ﬁle will load with partial support. Add LASTDRIVE=Z to the CONFIG.SYS ﬁle and reboot the workstation; then load the NETX.VLM ﬁle.

Explanation: This message is only a warning. However, if you want full compatibility with the NetWare® shell, you must set the DOS LASTDRIVE parameter in the CONFIG.SYS ﬁle to Z. Otherwise, problems occur when mapping drives, etc.

Action: Set LASTDRIVE=Z in the CONFIG.SYS ﬁle; then reboot the client workstation before loading the NetWare DOS Requester™ software.

NETX-1.00-58: The PRINT.VLM ﬁle has not been loaded. The NETX.VLM ﬁle will load successfully without print services. To enable printing services, load the PRINT.VLM ﬁle before loading the NETX.VLM ﬁle.

Explanation: This message is only a warning. For full NetWare® shell compatibility, the PRINT.VLM ﬁle must be loaded.

Action: If you want print functionality, load the PRINT.VLM ﬁle before loading the NETX.VLM ﬁle.

NMR-1.00-1: The message ﬁle <name> is invalid. The program cannot be loaded.

Explanation: The .MSG ﬁle is invalid. This problem could be the result of a corrupted ﬁle, a bad translation, or an outdated ﬁle version.

Action: Either update the .MSG ﬁle with a valid copy or delete the ﬁle. The NetWare® DOS Requester™ software uses the default messages that are bound to the binary ﬁles.

4-20

Image 192

HP UX Internet and Networking Software manual System Messages

Contents

HP 9000 Networking HP Part No. J2771-90016Edition Hewlett-Packard Co Homestead Road Cupertino, CA 95014 USA Printing History Preface Introduction Documentation Conventions This manual uses the following Novell conventions Asterisk Syntax Vii Supplemental Documentation Preface Preface Contents NET.CFG Options Reference Overview 2-2 Introduction Creating and Modifying a NET.CFG File Link Driver Option Alternate Link Support Option NetWare DOS Requester Option Network PRINTERS=number Protocol IPX Option 103 Protocol SPX OptionProtocol Tcpip Option Transport Provider IPX UDP Option Introduction Core NetWare Client Software Dosnp Software Optimizing the NetWare Client Software Overview Topic Introduction Using the Packet Burst Protocol Increasing SpeedRequirement for Packet Burst How Packet Burst Works Configuring for Packet Burst Using Large Internet Packet FunctionalityWhen to Use Packet Burst Disabling Packet Burst Configuring for Large Internet Packet When to Use Large Internet PacketHow Large Internet Packet Works Disabling LIP Using NCP Packet Signature to Improve Security Improving SecurityHow NCP Packet Signature Works When to Use NCP Packet Signature NCP Packet Signature OptionsNCP Packet Signature Levels Level Number Explanation Examples of Using Packet Signature Levels SolutionEffective Packet Signature Levels Server = Installing NCP Packet Signature Client Workstation Is Publicly AccessibleWorkstation Setting Client Workstation Users Often Change Locations Server Setting Disabling Packet Signature Troubleshooting NCP Packet Signature Client Workstations Are Not Signing Packets ProblemClient Workstations Cannot Log Third-Party NLM Programs Do Not Work Insecure Client Workstations Log In to a Secure Server Using Other Client Security Guidelines Additional Information Topic Reference NET.CFG Options Reference NET.CFG Options Reference Introduction Creating and Modifying a NET.CFG File Entering Options and Parameters into the NET.CFG File Sample NET.CFG File Following ﬁgure illustrates the NET.CFG ﬁle formatFollowing is a sample NET.CFG ﬁle that NET.CFG File Format NET.CFG file Using NET.CFG Options and Parameters NET.CFG Options Desktop snmp Link driver drivernameLink support Netware dos requester NET.CFG Options Protocol ipx Protocol spxProtocol tcpip Transport provider ipx udp Using the NET.CFG Reference Pages Format of NET.CFG Reference Pages Desktop Snmp Option Available Parameters and Values for the Desktop Snmp OptionCategory Parameters and Values MIB-II Asynchronous Timeout Connections Asynchronous Timeout numberSyntax Parameter and Value Default Example Community Types and Names Snmpenableauthentraps on Default Speciﬁes the monitor community nameDesktop Snmp Option Parameters for Community Names Parameter Explanation Community Access Management Speciﬁes the control community nameSpeciﬁes the trap community name Control Community name public private Desktop Snmp Option Values for Community Type Parameters Value Explanation Enables the value settings for the monitor community Enables the value settings for the control communityEnables the value settings for the trap community Example of NET.CFG Files Using the Community Name and Types MIB-II Management Information Base Support Desktop Snmp automatically supports three MIB-II groupsSystem and Snmp Groups That an unauthorized user is tying to access the network Explains these parametersAuthority Management stations or reported in Snmp traps Snmpenableauthentrap on off Syscontact contact Informs the Snmp manager of your username Syslocation locationSysname name Interface Group TCP/IP Groups Example of NET.CFG File Including Each Group Support Link Driver Option Available Parameters and Values for the Link Driver OptionLink Driver drivername This option has the following parameters and values BUS ID name number Bus Type Identiﬁcation Number ISA MCA Eisa Pcmcia PCIDMA #1 #2 channelnumber For example, the frame type Token-Ring can be used in LSB Frame frametypename addressingmode Frame Types, Protocols, and LAN Drivers List of Frame Types, Protocols, and LAN Drivers Frame Type and Description Protocols LAN Drivers For token ring, enable token ring frame types Ethernet LAN DriversToken-Ring LAN Drivers IRQ #1 #2 interruptrequestnumber MAX Frame Size number Speciﬁes a memory range to be used by the network board MEM #1 #2 hexstartingaddress hexlength Node Address hexaddress mode Replace hexstartingaddress with Lansup Port #1 #2 hexstartingaddress hexnumberofports Defined Protocols and Frame Types Allows existing LAN drivers to handle new network protocolsProtocol name hexprotocolID frametype Numbers Frame Protocol Frame Type Description Ethernetii IPX/SPXSlot number Listing of Commonly Used ODI LAN Drivers Driver Name Network Board COM Ceodi E20ODIE2HODI E30ODI Lansup MadgeodiNCRWL05 NE2 Nulldrv OC32TR16.COMOCTOK16.COM OSH391R Smcarcws SMC PC600WS/650WST20ODI T30ODI Link Support Option Available Parameters and Values for the Link Support Option Buffers communicationnumber buffersize Default Default Range Example MAX Boards number MAX Stacks number Mempool number k Link support Mempool NetWare DOS Requester Option Current Core Virtual Loadable Module VLM Programs Current Non-Core Virtual Loadable Module Programs Module Name Description Compatibility with NetWare Shell Parameters Parameters and Values Status Packets Managing the NetWare DOS Requester Condition ExplanationVLM=C\NWCLIENT\CONN.VLM Optimizing the NetWare DOS Requester VLM /C=C\NWCLIENT\NET.CFGBest Performance NetWare DOS Requester Option This entry indicates the following Best Conventional Memory Usage Best Compromise Parameters and Values NetWare DOS Requester Option Auto Large TABLE=on off Modules Default Modules Default Range ModulesAuto RECONNECT=on off AUTO.VLM, NDS.VLM Average Name LENGTH=number Bind RECONNECT=on off AUTO.VLM, BIND.VLMBroadcast RETRIES=number Broadcast Send DELAY=number Broadcast TIMEOUT=numberBetween performing any function Serial links on your network Cache Buffer SIZE=number Cache WRITES=on off CHECKSUM=number IPXNCP.VLM, NWP.VLM Confirm Critical Error ACTION=on off VLM.EXE Sets the name of the operating system used in the shell CONNECTIONS=numberAUTO.VLM, CONN.VLM, FIO.VLM, NDS.VLM SECURITY.VLM DOS NAME=name Msdos GENERAL.VLM, NETX.VLMEOJ=on off NETX.VLM, REDIR.VLM Exclude VLM=pathvlm Range ModulesFirst Network DRIVE=driveletter GENERAL.VLM, NETX.VLM, REDIR.VLM Handle NET ERRORS=on off Force First Network DRIVE=on off Large Internet PACKETS=on off Starting LIP negotiations Process across slow linksConnection table in an Upper Memory Block UMB, if available LIP Start SIZE=number Load LOW CONN=on off Load LOW IPXNCP=on off Load LOW REDIR=on off Local PRINTERS=number Lock DELAY=number Lock RETRIES=number Long Machine TYPE=name Allow several applications to run simultaneously IBM-PCMAX TASKS=number Message LEVEL=number Message TIMEOUT=number Default Range Minimum Time to NET=number Name CONTEXT=namecontext Netware PROTOCOL=netwareprotocollist Network PRINTERS=number Sets the read buffer size in bytes for MS Windows PB BUFFERS=numberFIO.VLM, IPXNCP.VLM Pburst Read Windows SIZE=number Sets the write buffer size in bytes for MS Windows Preferred TREE=treename Preferred WORKGROUP=workgroupname Print Buffer SIZE=number Print HEADER=number Print TAIL=number Read only COMPATIBILITY=on off RESPONDER=on off Search MODE=number Syntax Search mode=number Default Modules SET Station TIME=on off Short Machine TYPE=nameIBM Show DOTS=on off REDIR.EXESignature LEVEL=number = Enabled but not preferred = Preferred = Required Syntax True commit=on off Default Off ModulesNWP.VLM, SECURITY.VLM True COMMIT=on off USE DEFAULTS=on off VLM=pathVLM Workgroup NET=workgroupnetaddress 102 Protocol IPX Option Available Parameters and Values for the Protocol IPX Option Bind LANdrivername #number INT64 on off INT7A on off Ipatch byteoffset, value Syntax IPX Packet Size Limit number IPX Retry Count number IPX Sockets number 108 Protocol SPX Option Available Parameters and Values for the Protocol SPX Option SPX Abort Timeout number Minimum SPX Retries number SPX Listen Timeout number SPX Connections number SPX Verify Timeout number Protocol SPX Option 113 Protocol Tcpip Option LANNbadapter 0 Nbbrdcast 0 Nobootp LAN Drivers Bind odidriver number frametype networkname IP Addresses Speciﬁes the IP address for your client workstation Ipaddress ipaddress networkname Speciﬁes the default subnetwork mask if subnetworks are used Ipnetmask netmaskaddress networkname Connection Sockets Iprouter ipaddress networkname Transmission Control Protocol TCP Sockets Tcpsockets number User Datagram Protocol UDP Sockets Udpsockets number Raw Sockets Rawsockets number Additional Support Path Tcpcfg drive path Transport Provider IPX UDP Option Transport Provider IPX UDP Trap Target ipxaddress ipaddress Transport Provider IPX UDP Option 128 Command Line Parameters Reference Command Line Parameters Reference Convention Explanation Programname Core NetWare Client Software Explanation of the Core NetWare Client SoftwareSoftware Explanation IPXODI.COM Parameter Option Explanation Syntax for using these parameters is as follows This command indicates the following ODI LAN driver.COM VLM.EXE VLM /D /C=C\NWCLIENT\NET.CFG /PS=SALES /MC This command indicates the following Dosnp Software System Messages System Messages System Messages System Messages System Messages System Messages DOSCLINST-1.0-1 Filename could not be installed DOSCLINST-1.0-3 The INSTALL.OVL ﬁle could not be found Action Delete unnecessary ﬁles from the hard disk System Messages System Messages System Messages System Messages System Messages System Messages IPXNCP.VLM System Messages System Messages System Messages System Messages System Messages System Messages System Messages System Messages System Messages System Messages System Messages System Messages System Messages System Messages System Messages System Messages VLM-1.00-9 The VLM.EXE ﬁle is testing the VLMs System Messages System Messages VLM-1.00-37 The VLM.EXE ﬁle is using expanded memory EMS VLM-1.00-39 The VLM.EXE ﬁle is using extended memory XMS System Messages Try one or more of the following System Messages System Messages Index Enable Control Community Lock Delay NetWare DOS Requester Monitor Community Desktop Snmpenableauthentrap Unix conventions, explained commands Index