Network Parameters Menu | I-Tech Company CMS 6R4 Series instruction

Conﬁ guration

5.5.2.Network Parameters Menu

The Network Parameters Menu is used to select the IP Address and other network parameters.

•Web Browser Interface: Click the "Setup" button to access the Setup Menus, and then click the "Network Parameters" button. The Network Parameters Menu will be displayed as shown in Figure 5.9.

•Text Interface: Type /N and press [Enter]. The Network Parameters Menu will be displayed as shown in Figure 5.10.

Notes:

•Although the Web Browser Interface and Text Interface both allow conﬁguration of the same network parameters, note that for the Text Interface, the IP Security feature is conﬁgured via a separate submenu. For more information on IP Security, please refer to Section 5.5.2.1.

•In the Web Browser Interface, both Telnet Parameters and Web Server Parameters are deﬁned via separate menus, which are accessed using the buttons on the left hand edge of the Setup menu. In the Text Interface, these parameters are deﬁned via the Network Parameters Menu.

•Settings for network parameters depend on the conﬁguration of your individual network. Contact your network administrator for appropriate settings.

The Network Parameters Menus allow the following parameters to be deﬁned. Except where noted, all parameters listed here are available via both the Web Browser Interface and Text Interface.

Network Parameters:

•IP Address: Deﬁnes the IP address for the CMS-6R4 unit. (Default = 192.168.168.168.)

•Subnet Mask: Deﬁnes the Subnet Mask for the CMS-6R4 unit. (Default = 255.255.255.0.)

•Gateway Address: Deﬁnes the Gateway Address for the CMS-6R4 unit. (Default = undeﬁned.)

•Send MSS: Deﬁnes the Maximum Segment Size that will be sent by the CMS-6R4. (Default = 536.)

•IP Security: Sets up the IP Security feature. Please refer to Section 5.5.2.1 for a detailed description of the IP Security feature.

5-19

Image 41

I-Tech Company CMS 6R4 Series manual Network Parameters Menu

Contents

Distributed by Page Installation Instructions FCC Part 15 Regulation Table of Contents Upgrading the CMS-6R4 Firmware Command Reference Guide List of Figures CMS-6R4 Series User’s Guide Introduction Security Features and Co-Location FeaturesEasy to Configure, Easy to Use Typographic Conventions CMS-6R4 and CMS-6R4 CE Models Front Panel Components Unit Description Back Panel Components 120 VAC Model Shown Back Panel Components Unit Description CMS-6R4 Series User’s Guide Apply Power to the CMS-6R4 Hardware InstallationQuick Start Connect your PC to the CMS-6R4 Text Interface Communicating with the CMS-6R4 Plug Name Port Name CMD Access Status ModeStatus Default Connecting Ports and Switching Outlets Quick Start CMS-6R4 Series User’s Guide Power Supply Connection InstallationConnecting Devices to the Switched Outlets Installing the Cable Keeper Connecting Control Devices to the CMS-6R4 Connecting Devices to the RS232 Serial PortsConnecting the Network Cable Control via Local PC Supervisor Mode and Non-Supervisor Mode Configuration Communicating with the CMS-6R4 Main Status Screen Web Browser Interface Sample Values Shown Accessing the Web Browser Interface Plug Name BOOT/SEQ Delay Status Default Accessing the Text InterfaceCMS-6R4 Port Name $ telnet 192.168.168.168 Enter System SetUp Port Password Functions System Parameters Menu Configuration Menus System Parameters System Parameters Menu Web Browser Interface Conﬁ guration Password Directory Edit Password Directory Password Directory Menu Web Browser Interface Adding Passwords ESC ADD NAME/PASSWORD CMS-6R4 Series User’s Guide Editing Passwords Deleting the Entire Password Directory Deleting Passwords Dial Back Function User Account Parameters Dial Back ExampleSystem Parameters Menu Network Parameters Network Parameters Menu WEB Server Network ParametersTelnet Parameters MAC Address Telnet ParametersWeb Server IP Security IP Security Feature Conﬁ guration Telnet Port Parameters 12 The Telnet Port Parameters Menu Text Interface Telnet Port Parameters CMS-6R4 Series User’s Guide Conﬁ guration Invalid Access Lockout Feature 3. RS232 Port Parameters 14 Port Parameters Menu Web Browser Interface Conﬁ guration CMS-6R4 Series User’s Guide Conﬁ guration CMS-6R4 Series User’s Guide 3.1. RS232 Port Modes Copy Serial Port Parameters Copying Parameters to Several Ports Conﬁ guration Text Interface Type /P 7 and press Enter Configuring the Internal Modem Plug Parameters Menus Plug #1 Parameters 17 Plug Parameters Menu Web Browser Interface Reboot Cycles Boot / Sequence Delay Period Save Configuration Parameters Status Screen Web Browser Interface OperationOperation via the Web Browser Interface Status Menu Web Browser Interface DPL Operation via the Text Interface Status Screen Text Interface Port Name CMD Access On 1 or /ON Router Switching Outlets Text Interface Connections Between RS232 Ports Text Interface Applying Commands to Several Outlets Text InterfaceBO * Enter Connecting Ports Three Characters Uses the format EnterLLLEnter, where Disconnecting Ports Enter CMS-6R4 Series User’s Guide Server Enter Defining Hunt Groups Passive Mode Any-to-Any ModePort Modes Hunt Group Example Reading Data from Buffer Mode Ports Buffer Mode Port Buffers Modem Mode Automated Mode Logging Out of Command Mode Operation Standard Telnet Protocol and Raw Socket Mode Direct Connect Feature Direct Connect Configuration Connection Example Connecting to a Serial Port using Direct Connect Terminating a Direct Connect Session Manual Operation Port Section Status ScreensMain Status Screen /S Main Status Screen Plug Section Network Status Screen /SN Port Diagnostics Name Status Baud COM HS Mode Port Diagnostics Screen /SDCTS RTS Port Parameters Screen Serial Ports Port Parameters Screen /WPort Parameters #3 RTS/CTS Port Parameters Screen Network Port Shown Port Parameters Screen Network Port Super User Directory CMS-6R4 Series User’s Guide Sending Parameters to a File Saving and Restoring Configuration Parameters Restoring Saved Parameters Upgrading the CMS-6R4 Firmware CMS-6R4 Series User’s Guide 10-1 Command Reference GuideCommand Conventions 10-2 Command Summary 10-3 Command Response Messages Initiate Boot Cycle Command SetResponse 10-4 Format /C x x Enter ConnectTerse 10-5 10-6 Copy RS232 Port ParametersThird Party Disconnect Format /DPL,Y Enter Set Plugs to Default StateErase Buffer Format /E,Y x x Enter Set System Parameters Set to Factory DefaultsHelp 10-8 Display Site ID Reset Network InterfaceSet Network Port Parameters 10-9 10-10 Switch Plugs OffFormat /OFF,Y n Enter or /OF,Y Enter 10-11 Switch Plugs onSet RS232 Port Parameters Set Plug Parameters Display Port DiagnosticsDisplay Main Status Screen 10-12 Display Network Status Upgrade FirmwareTelnet Telnet Connection Out Send Parameters to a File View Password Directory Unlock Port Invalid Access LockoutDisplay Port Parameters Who 10-14 Format Default Response Exit Command ModeFormat /X,Y Enter Resident Disconnect Sequence 10-16 Apx-1 Interface DescriptionSerial RS232 Port Interface Apx-2 Specifications Apx-3 Customer Service Apx-4 Trademark and Copyright Information Index-1 Index Index-2 Index Index-3 Index-4