Quick Start, Hardware Installation | I-Tech Company CMS 6R4 Series

3. Quick Start

This Quick Start Guide describes a simpliﬁed installation procedure for the CMS-6R4 hardware, which will allow you to communicate with the unit in order to demonstrate basic features and check for proper operation.

Note that this Quick Start Guide does not provide a detailed description of unit conﬁguration, or discuss advanced operating features in detail. For more information, please refer to the Installation, Conﬁguration and Operation sections in this User's Guide.

3.1.Hardware Installation

3.1.1.Apply Power to the CMS-6R4

Refer to the safety precautions listed at the beginning of this User's Guide, and then connect the unit to an appropriate power source. Connect the power supply cable to the unit’s power inlet, snap the Cable Keeper into place, and then connect the cable to an appropriate power supply.

Note: The CMS-6R4 is designed for 100 to 120 VAC operation and the CMS-6R4-CE is designed for 100 to 240 VAC operation.

When power is applied to the CMS-6R4, the ON LED should light, and the RDY LED should begin to ﬂash. This indicates that the unit is ready to receive commands.

3.1.2.Connect your PC to the CMS-6R4

The CMS-6R4 can either be controlled by a local PC Serial Port, controlled via modem, or controlled via TCP/IP network. In order to select parameters, connect ports or control outlets, commands are issued to the CMS-6R4 via either the Network Port, Modem Port or a Serial RS232 Port.

•Network Port: Connect the CMS-6R4 10Base-T, half duplex network interface to your network.

•Serial Port: Use the supplied null modem cable to connect your PC COM port to Serial Port 1 (The System Setup Port.)

•Modem: Connect your telephone line to the CMS-6R4 Phone Line Port.

3-1

Image 15

I-Tech Company CMS 6R4 Series manual Quick Start, Hardware Installation, Apply Power to the CMS-6R4

Contents

Distributed by Page Installation Instructions FCC Part 15 Regulation Table of Contents Upgrading the CMS-6R4 Firmware Command Reference Guide List of Figures CMS-6R4 Series User’s Guide Security Features and Co-Location Features Easy to Configure, Easy to UseIntroduction Typographic Conventions CMS-6R4 and CMS-6R4 CE Models Front Panel Components Unit Description Back Panel Components 120 VAC Model Shown Back Panel Components Unit Description CMS-6R4 Series User’s Guide Connect your PC to the CMS-6R4 Hardware InstallationApply Power to the CMS-6R4 Quick Start Text Interface Communicating with the CMS-6R4 Port Name CMD Access Status Mode Status DefaultPlug Name Connecting Ports and Switching Outlets Quick Start CMS-6R4 Series User’s Guide Installing the Cable Keeper InstallationPower Supply Connection Connecting Devices to the Switched Outlets Control via Local PC Connecting Devices to the RS232 Serial PortsConnecting Control Devices to the CMS-6R4 Connecting the Network Cable Supervisor Mode and Non-Supervisor Mode Configuration Communicating with the CMS-6R4 Main Status Screen Web Browser Interface Sample Values Shown Accessing the Web Browser Interface Port Name Accessing the Text InterfacePlug Name BOOT/SEQ Delay Status Default CMS-6R4 $ telnet 192.168.168.168 Enter System SetUp Port Password Functions System Parameters Menu Configuration Menus System Parameters System Parameters Menu Web Browser Interface Conﬁ guration Password Directory Edit Password Directory Password Directory Menu Web Browser Interface Adding Passwords ESC ADD NAME/PASSWORD CMS-6R4 Series User’s Guide Editing Passwords Deleting the Entire Password Directory Deleting Passwords Dial Back Function Dial Back Example System Parameters MenuUser Account Parameters Network Parameters Network Parameters Menu Network Parameters Telnet ParametersWEB Server Telnet Parameters Web ServerMAC Address IP Security IP Security Feature Conﬁ guration Telnet Port Parameters 12 The Telnet Port Parameters Menu Text Interface Telnet Port Parameters CMS-6R4 Series User’s Guide Conﬁ guration Invalid Access Lockout Feature 3. RS232 Port Parameters 14 Port Parameters Menu Web Browser Interface Conﬁ guration CMS-6R4 Series User’s Guide Conﬁ guration CMS-6R4 Series User’s Guide 3.1. RS232 Port Modes Copy Serial Port Parameters Copying Parameters to Several Ports Conﬁ guration Text Interface Type /P 7 and press Enter Configuring the Internal Modem Plug Parameters Menus Plug #1 Parameters 17 Plug Parameters Menu Web Browser Interface Reboot Cycles Boot / Sequence Delay Period Save Configuration Parameters Operation Operation via the Web Browser InterfaceStatus Screen Web Browser Interface Status Menu Web Browser Interface DPL Operation via the Text Interface Status Screen Text Interface Port Name CMD Access On 1 or /ON Router Switching Outlets Text Interface Applying Commands to Several Outlets Text Interface BO * EnterConnections Between RS232 Ports Text Interface Connecting Ports Three Characters Uses the format EnterLLLEnter, where Disconnecting Ports Enter CMS-6R4 Series User’s Guide Server Enter Defining Hunt Groups Hunt Group Example Any-to-Any ModePassive Mode Port Modes Reading Data from Buffer Mode Ports Buffer Mode Port Buffers Modem Mode Automated Mode Logging Out of Command Mode Operation Standard Telnet Protocol and Raw Socket Mode Direct Connect Feature Direct Connect Configuration Connection Example Connecting to a Serial Port using Direct Connect Terminating a Direct Connect Session Manual Operation Status Screens Main Status Screen /SPort Section Main Status Screen Plug Section Network Status Screen /SN RTS Port Diagnostics Screen /SDPort Diagnostics Name Status Baud COM HS Mode CTS RTS/CTS Port Parameters Screen /WPort Parameters Screen Serial Ports Port Parameters #3 Port Parameters Screen Network Port Shown Port Parameters Screen Network Port Super User Directory CMS-6R4 Series User’s Guide Sending Parameters to a File Saving and Restoring Configuration Parameters Restoring Saved Parameters Upgrading the CMS-6R4 Firmware CMS-6R4 Series User’s Guide Command Reference Guide Command Conventions10-1 10-2 Command Summary 10-3 Command Response Messages 10-4 Command SetInitiate Boot Cycle Response 10-5 ConnectFormat /C x x Enter Terse Copy RS232 Port Parameters Third Party Disconnect10-6 Format /E,Y x x Enter Set Plugs to Default StateFormat /DPL,Y Enter Erase Buffer 10-8 Set to Factory DefaultsSet System Parameters Help 10-9 Reset Network InterfaceDisplay Site ID Set Network Port Parameters Switch Plugs Off Format /OFF,Y n Enter or /OF,Y Enter10-10 Switch Plugs on Set RS232 Port Parameters10-11 10-12 Display Port DiagnosticsSet Plug Parameters Display Main Status Screen Send Parameters to a File Upgrade FirmwareDisplay Network Status Telnet Telnet Connection Out 10-14 Unlock Port Invalid Access LockoutView Password Directory Display Port Parameters Who Resident Disconnect Sequence Exit Command ModeFormat Default Response Format /X,Y Enter 10-16 Interface Description Serial RS232 Port InterfaceApx-1 Apx-2 Specifications Apx-3 Customer Service Apx-4 Trademark and Copyright Information Index-1 Index Index-2 Index Index-3 Index-4