CMS-6R4 Series User’s Guide | I-Tech Company CMS 6R4 Series instruction

CMS-6R4 Series - User’s Guide

•Direct Connect: Direct Connect allows you to access the CMS-6R4 and automatically create a connection between the Network Port and a speciﬁc RS232 port by including the appropriate Telnet port number in the connect command (e.g. Port 5 = 2105). For more information, please refer to Section 6.6. As described below, the Direct Connect feature offers three options. (Default = Off.)

Off: Telnet users will not be able to employ the Direct Connect feature to connect to this port.

On - No Password: Telnet users will be able to employ the Direct Connect feature to connect to this port without entering a password.

On - Password: Telnet users will be able to use Direct Connect to connect to this port, but will be required to enter a password before the connection is established.

Note: If "On - Password" is selected, and Supervisor commands are disabled at the Network Port, then only accounts that do not permit Supervisor commands will be allowed to establish a direct connection via the Network Port. If Supervisor commands are disabled at a given port, then that port will not allow access by accounts that permit Supervisor commands.

When the Port Parameters menu is accessed via the Text Interface, the menu also lists both Direct Connect port numbers for this port (port numbers are not listed in the Web Browser Interface.)

Telnet Port: The Telnet port number that is used to create a Direct Connection to this port using standard Telnet protocol.

Raw Port: The Telnet port number that is used to create a Raw Socket connection to this port. When Raw Socket Mode is used, data is always sent "as is", and command echo is always enabled.

5-34

Image 56

I-Tech Company CMS 6R4 Series manual CMS-6R4 Series User’s Guide

Contents

Distributed by Page Installation Instructions FCC Part 15 Regulation Table of Contents Upgrading the CMS-6R4 Firmware Command Reference Guide List of Figures CMS-6R4 Series User’s Guide Introduction Security Features and Co-Location FeaturesEasy to Configure, Easy to Use CMS-6R4 and CMS-6R4 CE Models Typographic Conventions Unit Description Front Panel Components Back Panel Components Back Panel Components 120 VAC Model Shown Unit Description CMS-6R4 Series User’s Guide Hardware Installation Apply Power to the CMS-6R4Quick Start Connect your PC to the CMS-6R4 Communicating with the CMS-6R4 Text Interface Plug Name Port Name CMD Access Status ModeStatus Default Connecting Ports and Switching Outlets Quick Start CMS-6R4 Series User’s Guide Installation Power Supply ConnectionConnecting Devices to the Switched Outlets Installing the Cable Keeper Connecting Devices to the RS232 Serial Ports Connecting Control Devices to the CMS-6R4Connecting the Network Cable Control via Local PC Configuration Supervisor Mode and Non-Supervisor Mode Communicating with the CMS-6R4 Accessing the Web Browser Interface Main Status Screen Web Browser Interface Sample Values Shown Accessing the Text Interface Plug Name BOOT/SEQ Delay Status DefaultCMS-6R4 Port Name System SetUp Port $ telnet 192.168.168.168 Enter Password Functions Configuration Menus System Parameters Menu System Parameters Menu Web Browser Interface System Parameters Conﬁ guration Password Directory Password Directory Menu Web Browser Interface Edit Password Directory Adding Passwords ADD NAME/PASSWORD ESC CMS-6R4 Series User’s Guide Editing Passwords Deleting Passwords Deleting the Entire Password Directory Dial Back Function User Account Parameters Dial Back ExampleSystem Parameters Menu Network Parameters Menu Network Parameters WEB Server Network ParametersTelnet Parameters MAC Address Telnet ParametersWeb Server IP Security Feature IP Security Conﬁ guration 12 The Telnet Port Parameters Menu Text Interface Telnet Port Parameters Telnet Port Parameters CMS-6R4 Series User’s Guide Conﬁ guration Invalid Access Lockout Feature 3. RS232 Port Parameters 14 Port Parameters Menu Web Browser Interface Conﬁ guration CMS-6R4 Series User’s Guide Conﬁ guration CMS-6R4 Series User’s Guide 3.1. RS232 Port Modes Copying Parameters to Several Ports Copy Serial Port Parameters Conﬁ guration Configuring the Internal Modem Text Interface Type /P 7 and press Enter Plug Parameters Menus 17 Plug Parameters Menu Web Browser Interface Plug #1 Parameters Boot / Sequence Delay Period Reboot Cycles Save Configuration Parameters Status Screen Web Browser Interface OperationOperation via the Web Browser Interface Status Menu Web Browser Interface Operation via the Text Interface DPL Port Name CMD Access Status Screen Text Interface Switching Outlets Text Interface On 1 or /ON Router Connections Between RS232 Ports Text Interface Applying Commands to Several Outlets Text InterfaceBO * Enter Connecting Ports Disconnecting Ports Three Characters Uses the format EnterLLLEnter, where Enter CMS-6R4 Series User’s Guide Defining Hunt Groups Server Enter Any-to-Any Mode Passive ModePort Modes Hunt Group Example Buffer Mode Reading Data from Buffer Mode Ports Port Buffers Modem Mode Logging Out of Command Mode Automated Mode Operation Direct Connect Feature Standard Telnet Protocol and Raw Socket Mode Direct Connect Configuration Connecting to a Serial Port using Direct Connect Connection Example Terminating a Direct Connect Session Manual Operation Port Section Status ScreensMain Status Screen /S Plug Section Main Status Screen Network Status Screen /SN Port Diagnostics Screen /SD Port Diagnostics Name Status Baud COM HS ModeCTS RTS Port Parameters Screen /W Port Parameters Screen Serial PortsPort Parameters #3 RTS/CTS Port Parameters Screen Network Port Port Parameters Screen Network Port Shown User Directory Super CMS-6R4 Series User’s Guide Saving and Restoring Configuration Parameters Sending Parameters to a File Restoring Saved Parameters Upgrading the CMS-6R4 Firmware CMS-6R4 Series User’s Guide 10-1 Command Reference GuideCommand Conventions Command Summary 10-2 Command Response Messages 10-3 Command Set Initiate Boot CycleResponse 10-4 Connect Format /C x x EnterTerse 10-5 10-6 Copy RS232 Port ParametersThird Party Disconnect Set Plugs to Default State Format /DPL,Y EnterErase Buffer Format /E,Y x x Enter Set to Factory Defaults Set System ParametersHelp 10-8 Reset Network Interface Display Site IDSet Network Port Parameters 10-9 10-10 Switch Plugs OffFormat /OFF,Y n Enter or /OF,Y Enter 10-11 Switch Plugs onSet RS232 Port Parameters Display Port Diagnostics Set Plug ParametersDisplay Main Status Screen 10-12 Upgrade Firmware Display Network StatusTelnet Telnet Connection Out Send Parameters to a File Unlock Port Invalid Access Lockout View Password DirectoryDisplay Port Parameters Who 10-14 Exit Command Mode Format Default ResponseFormat /X,Y Enter Resident Disconnect Sequence 10-16 Apx-1 Interface DescriptionSerial RS232 Port Interface Specifications Apx-2 Customer Service Apx-3 Trademark and Copyright Information Apx-4 Index Index-1 Index-2 Index-3 Index Index-4