Installation | I-Tech Company CMS 6R4 Series instruction

4. Installation

This Section provides further details regarding installation of the CMS-6R4.

4.1. Power Supply Connection

Use the supplied power cord to connect the CMS-6R4 to an appropriate power supply. Note that the CMS-6R4's Main Power switch must be "On" in order for the unit to operate.

CAUTIONS:

•Before attempting to install this unit, please review the warnings and cautions listed at the front of the user's guide.

•This device should only be operated with the type of power source indicated on the instrument nameplate. If you are not sure of the type of power service available, please contact your local power company.

•Reliable earthing (grounding) of this unit must be maintained. Particular attention should be given to supply connections when connecting to power strips, rather than directly to the branch circuit.

4.1.1.Installing the Cable Keeper

The CMS-6R4 includes a cable keeper, which is designed to prevent the power supply cable from being accidentally disconnected from the unit.

When attaching the power supply cable to the unit, ﬁrst swing the cable keeper out of the way, then plug the power cable securely into the power input. When the cable is in place, snap the cable keeper over the plug to secure the cable to the unit.

4.2. Connecting Devices to the Switched Outlets

Connect the power cord from your switched device to a switched AC Outlet on the CMS-6R4 back panel. Note that when power is applied to the CMS-6R4, the Switched AC Outlets will be switched "ON". Note that the CMS-6R4

(120 VAC Model) is designed for 100 to 120 VAC operation and will support up to 15 Amps maximum, and the CMS-6R4-CE (230 VAC Model) is designed for 100 to 240 VAC operation and will support up to 10 Amps maximum.

4-1

Image 21

I-Tech Company CMS 6R4 Series manual Installation, Power Supply Connection, Connecting Devices to the Switched Outlets

Contents

Distributed by Page Installation Instructions FCC Part 15 Regulation Table of Contents Upgrading the CMS-6R4 Firmware Command Reference Guide List of Figures CMS-6R4 Series User’s Guide Security Features and Co-Location Features Easy to Configure, Easy to UseIntroduction Typographic Conventions CMS-6R4 and CMS-6R4 CE Models Front Panel Components Unit Description Back Panel Components 120 VAC Model Shown Back Panel Components Unit Description CMS-6R4 Series User’s Guide Apply Power to the CMS-6R4 Hardware InstallationQuick Start Connect your PC to the CMS-6R4 Text Interface Communicating with the CMS-6R4 Port Name CMD Access Status Mode Status DefaultPlug Name Connecting Ports and Switching Outlets Quick Start CMS-6R4 Series User’s Guide Power Supply Connection InstallationConnecting Devices to the Switched Outlets Installing the Cable Keeper Connecting Control Devices to the CMS-6R4 Connecting Devices to the RS232 Serial PortsConnecting the Network Cable Control via Local PC Supervisor Mode and Non-Supervisor Mode Configuration Communicating with the CMS-6R4 Main Status Screen Web Browser Interface Sample Values Shown Accessing the Web Browser Interface Plug Name BOOT/SEQ Delay Status Default Accessing the Text InterfaceCMS-6R4 Port Name $ telnet 192.168.168.168 Enter System SetUp Port Password Functions System Parameters Menu Configuration Menus System Parameters System Parameters Menu Web Browser Interface Conﬁ guration Password Directory Edit Password Directory Password Directory Menu Web Browser Interface Adding Passwords ESC ADD NAME/PASSWORD CMS-6R4 Series User’s Guide Editing Passwords Deleting the Entire Password Directory Deleting Passwords Dial Back Function Dial Back Example System Parameters MenuUser Account Parameters Network Parameters Network Parameters Menu Network Parameters Telnet ParametersWEB Server Telnet Parameters Web ServerMAC Address IP Security IP Security Feature Conﬁ guration Telnet Port Parameters 12 The Telnet Port Parameters Menu Text Interface Telnet Port Parameters CMS-6R4 Series User’s Guide Conﬁ guration Invalid Access Lockout Feature 3. RS232 Port Parameters 14 Port Parameters Menu Web Browser Interface Conﬁ guration CMS-6R4 Series User’s Guide Conﬁ guration CMS-6R4 Series User’s Guide 3.1. RS232 Port Modes Copy Serial Port Parameters Copying Parameters to Several Ports Conﬁ guration Text Interface Type /P 7 and press Enter Configuring the Internal Modem Plug Parameters Menus Plug #1 Parameters 17 Plug Parameters Menu Web Browser Interface Reboot Cycles Boot / Sequence Delay Period Save Configuration Parameters Operation Operation via the Web Browser InterfaceStatus Screen Web Browser Interface Status Menu Web Browser Interface DPL Operation via the Text Interface Status Screen Text Interface Port Name CMD Access On 1 or /ON Router Switching Outlets Text Interface Applying Commands to Several Outlets Text Interface BO * EnterConnections Between RS232 Ports Text Interface Connecting Ports Three Characters Uses the format EnterLLLEnter, where Disconnecting Ports Enter CMS-6R4 Series User’s Guide Server Enter Defining Hunt Groups Passive Mode Any-to-Any ModePort Modes Hunt Group Example Reading Data from Buffer Mode Ports Buffer Mode Port Buffers Modem Mode Automated Mode Logging Out of Command Mode Operation Standard Telnet Protocol and Raw Socket Mode Direct Connect Feature Direct Connect Configuration Connection Example Connecting to a Serial Port using Direct Connect Terminating a Direct Connect Session Manual Operation Status Screens Main Status Screen /SPort Section Main Status Screen Plug Section Network Status Screen /SN Port Diagnostics Name Status Baud COM HS Mode Port Diagnostics Screen /SDCTS RTS Port Parameters Screen Serial Ports Port Parameters Screen /WPort Parameters #3 RTS/CTS Port Parameters Screen Network Port Shown Port Parameters Screen Network Port Super User Directory CMS-6R4 Series User’s Guide Sending Parameters to a File Saving and Restoring Configuration Parameters Restoring Saved Parameters Upgrading the CMS-6R4 Firmware CMS-6R4 Series User’s Guide Command Reference Guide Command Conventions10-1 10-2 Command Summary 10-3 Command Response Messages Initiate Boot Cycle Command SetResponse 10-4 Format /C x x Enter ConnectTerse 10-5 Copy RS232 Port Parameters Third Party Disconnect10-6 Format /DPL,Y Enter Set Plugs to Default StateErase Buffer Format /E,Y x x Enter Set System Parameters Set to Factory DefaultsHelp 10-8 Display Site ID Reset Network InterfaceSet Network Port Parameters 10-9 Switch Plugs Off Format /OFF,Y n Enter or /OF,Y Enter10-10 Switch Plugs on Set RS232 Port Parameters10-11 Set Plug Parameters Display Port DiagnosticsDisplay Main Status Screen 10-12 Display Network Status Upgrade FirmwareTelnet Telnet Connection Out Send Parameters to a File View Password Directory Unlock Port Invalid Access LockoutDisplay Port Parameters Who 10-14 Format Default Response Exit Command ModeFormat /X,Y Enter Resident Disconnect Sequence 10-16 Interface Description Serial RS232 Port InterfaceApx-1 Apx-2 Specifications Apx-3 Customer Service Apx-4 Trademark and Copyright Information Index-1 Index Index-2 Index Index-3 Index-4