Manuals / I-Tech Company / Computer Equipment / Network Card

I-Tech Company CMS 6R4 Series Exit Command Mode, Format /X,Y Enter, Resident Disconnect Sequence

Models: CMS 6R4 Series

1 123

Download 123 pages 61.16 Kb

Page 113

Command Reference Guide

/X	Exit Command Mode

Exits command mode. When issued at the Net Port, also ends the Telnet session. Note that exiting from command mode will not terminate port connections.

•Any-to-Any Mode: Exits command mode.

•Modem Mode: Disconnects and resets modem, hang-up message is sent, hardware line to modem drops for 500 ms, and reset message is sent.

Availability: Supervisor / Non-Supervisor

Format: /X[,Y] [Enter]

Where ,Y is a command argument that can be used to suppress the command conﬁrmation prompt.

Response:

Verbose: Disconnected.

Terse: 3.

^X	Resident Disconnect Sequence

The Resident Disconnect Sequence is used to disconnect your resident port from another port as described in Section 6.2.3.2. Although the default Resident Disconnect Sequence is ^X ([Ctrl] plus [X]), the command can be redeﬁned via the Port Conﬁguration Menus as described in Section 5.5.

Note: The Resident Disconnect Sequence cannot be used to terminate a Direct Connection.

Availability: Supervisor / Non-Supervisor

Format (Default): ^X

Response:

Verbose: The CMS-6R4 will send the "Disconnected" message, followed by the Port Status Screen.

Terse: 3

10-15

Image 113

I-Tech Company CMS 6R4 Series Exit Command Mode, Format /X,Y Enter, Resident Disconnect Sequence, Format Default Response

Contents

Distributed by Page Installation Instructions FCC Part 15 Regulation Table of Contents Upgrading the CMS-6R4 Firmware Command Reference Guide List of Figures CMS-6R4 Series User’s Guide Introduction Security Features and Co-Location FeaturesEasy to Configure, Easy to Use Typographic Conventions CMS-6R4 and CMS-6R4 CE ModelsFront Panel Components Unit DescriptionBack Panel Components 120 VAC Model Shown Back Panel ComponentsUnit Description CMS-6R4 Series User’s Guide Apply Power to the CMS-6R4 Hardware InstallationQuick Start Connect your PC to the CMS-6R4Text Interface Communicating with the CMS-6R4Plug Name Port Name CMD Access Status ModeStatus Default Connecting Ports and Switching Outlets Quick Start CMS-6R4 Series User’s Guide Power Supply Connection InstallationConnecting Devices to the Switched Outlets Installing the Cable KeeperConnecting Control Devices to the CMS-6R4 Connecting Devices to the RS232 Serial PortsConnecting the Network Cable Control via Local PCSupervisor Mode and Non-Supervisor Mode ConfigurationCommunicating with the CMS-6R4 Main Status Screen Web Browser Interface Sample Values Shown Accessing the Web Browser InterfacePlug Name BOOT/SEQ Delay Status Default Accessing the Text InterfaceCMS-6R4 Port Name$ telnet 192.168.168.168 Enter System SetUp PortPassword Functions System Parameters Menu Configuration MenusSystem Parameters System Parameters Menu Web Browser InterfaceConﬁ guration Password Directory Edit Password Directory Password Directory Menu Web Browser InterfaceAdding Passwords ESC ADD NAME/PASSWORDCMS-6R4 Series User’s Guide Editing Passwords Deleting the Entire Password Directory Deleting PasswordsDial Back Function User Account Parameters Dial Back ExampleSystem Parameters Menu Network Parameters Network Parameters MenuWEB Server Network ParametersTelnet Parameters MAC Address Telnet ParametersWeb Server IP Security IP Security FeatureConﬁ guration Telnet Port Parameters 12 The Telnet Port Parameters Menu Text InterfaceTelnet Port Parameters CMS-6R4 Series User’s Guide Conﬁ guration Invalid Access Lockout Feature 3. RS232 Port Parameters 14 Port Parameters Menu Web Browser Interface Conﬁ guration CMS-6R4 Series User’s Guide Conﬁ guration CMS-6R4 Series User’s Guide 3.1. RS232 Port Modes Copy Serial Port Parameters Copying Parameters to Several PortsConﬁ guration Text Interface Type /P 7 and press Enter Configuring the Internal ModemPlug Parameters Menus Plug #1 Parameters 17 Plug Parameters Menu Web Browser InterfaceReboot Cycles Boot / Sequence Delay PeriodSave Configuration Parameters Status Screen Web Browser Interface OperationOperation via the Web Browser Interface Status Menu Web Browser Interface DPL Operation via the Text InterfaceStatus Screen Text Interface Port Name CMD AccessOn 1 or /ON Router Switching Outlets Text InterfaceConnections Between RS232 Ports Text Interface Applying Commands to Several Outlets Text InterfaceBO * Enter Connecting Ports Three Characters Uses the format EnterLLLEnter, where Disconnecting PortsEnter CMS-6R4 Series User’s Guide Server Enter Defining Hunt GroupsPassive Mode Any-to-Any ModePort Modes Hunt Group ExampleReading Data from Buffer Mode Ports Buffer ModePort Buffers Modem Mode Automated Mode Logging Out of Command ModeOperation Standard Telnet Protocol and Raw Socket Mode Direct Connect FeatureDirect Connect Configuration Connection Example Connecting to a Serial Port using Direct ConnectTerminating a Direct Connect Session Manual Operation Port Section Status ScreensMain Status Screen /S Main Status Screen Plug SectionNetwork Status Screen /SN Port Diagnostics Name Status Baud COM HS Mode Port Diagnostics Screen /SDCTS RTSPort Parameters Screen Serial Ports Port Parameters Screen /WPort Parameters #3 RTS/CTSPort Parameters Screen Network Port Shown Port Parameters Screen Network PortSuper User DirectoryCMS-6R4 Series User’s Guide Sending Parameters to a File Saving and Restoring Configuration ParametersRestoring Saved Parameters Upgrading the CMS-6R4 Firmware CMS-6R4 Series User’s Guide 10-1 Command Reference GuideCommand Conventions 10-2 Command Summary10-3 Command Response MessagesInitiate Boot Cycle Command SetResponse 10-4Format /C x x Enter ConnectTerse 10-510-6 Copy RS232 Port ParametersThird Party Disconnect Format /DPL,Y Enter Set Plugs to Default StateErase Buffer Format /E,Y x x EnterSet System Parameters Set to Factory DefaultsHelp 10-8Display Site ID Reset Network InterfaceSet Network Port Parameters 10-910-10 Switch Plugs OffFormat /OFF,Y n Enter or /OF,Y Enter 10-11 Switch Plugs onSet RS232 Port Parameters Set Plug Parameters Display Port DiagnosticsDisplay Main Status Screen 10-12Display Network Status Upgrade FirmwareTelnet Telnet Connection Out Send Parameters to a FileView Password Directory Unlock Port Invalid Access LockoutDisplay Port Parameters Who 10-14Format Default Response Exit Command ModeFormat /X,Y Enter Resident Disconnect Sequence10-16 Apx-1 Interface DescriptionSerial RS232 Port Interface Apx-2 SpecificationsApx-3 Customer ServiceApx-4 Trademark and Copyright InformationIndex-1 IndexIndex-2 Index Index-3Index-4