Command Reference Guide, 10-1 | I-Tech Company CMS 6R4 Series

10. Command Reference Guide

10.1. Command Conventions

Most commands described in this section conform to the following conventions:

•Text Interface: Commands discussed in this section, can only be invoked via the Text Interface. These commands cannot be invoked via the Web Browser Interface.

•Slash Character: Most CMS-6R4 commands begin with the Slash Character (/).

•Port Name Wild Card: It is not always necessary to enter the entire port name. Port names can be abbreviated in command lines by entering the ﬁrst character(s) of the name followed by an asterisk (*). For example, a port named "SERVER" can be speciﬁed as "S*". Note however, that this command would also be applied to any other port name that begins with an "S".

•Suppress "Sure?" Prompt: The ,Y option can be included in the command line to override the "Sure?" prompt. For example, to disconnect Port 8 without displaying the Sure prompt, type /D,Y 8 and then press [Enter].

•Enter Key: Most commands are invoked by pressing [Enter].

•Connected Ports: When two ports are connected, most CMS-6R4 commands will not be recognized by either of the connected ports. The only exceptions are the Resident Disconnect Sequence (Default = ^X ([Ctrl] plus [X])) and the Send Break command (^\ ([Ctrl] plus [\])

•Conﬁguration Menus: To exit from a conﬁguration menu, press [Esc]. The only exception to this rule is the Copy Parameters Menu (/CP), and in that case the [Esc] key is used to conﬁrm the copy operation.

10-1

Image 99

I-Tech Company CMS 6R4 Series manual Command Reference Guide, Command Conventions, 10-1

Contents

Distributed by Page Installation Instructions FCC Part 15 Regulation Table of Contents Upgrading the CMS-6R4 Firmware Command Reference Guide List of Figures CMS-6R4 Series User’s Guide Security Features and Co-Location Features Easy to Configure, Easy to UseIntroduction Typographic Conventions CMS-6R4 and CMS-6R4 CE Models Front Panel Components Unit Description Back Panel Components 120 VAC Model Shown Back Panel Components Unit Description CMS-6R4 Series User’s Guide Connect your PC to the CMS-6R4 Hardware InstallationApply Power to the CMS-6R4 Quick Start Text Interface Communicating with the CMS-6R4 Port Name CMD Access Status Mode Status DefaultPlug Name Connecting Ports and Switching Outlets Quick Start CMS-6R4 Series User’s Guide Installing the Cable Keeper InstallationPower Supply Connection Connecting Devices to the Switched Outlets Control via Local PC Connecting Devices to the RS232 Serial PortsConnecting Control Devices to the CMS-6R4 Connecting the Network Cable Supervisor Mode and Non-Supervisor Mode Configuration Communicating with the CMS-6R4 Main Status Screen Web Browser Interface Sample Values Shown Accessing the Web Browser Interface Port Name Accessing the Text InterfacePlug Name BOOT/SEQ Delay Status Default CMS-6R4 $ telnet 192.168.168.168 Enter System SetUp Port Password Functions System Parameters Menu Configuration Menus System Parameters System Parameters Menu Web Browser Interface Conﬁ guration Password Directory Edit Password Directory Password Directory Menu Web Browser Interface Adding Passwords ESC ADD NAME/PASSWORD CMS-6R4 Series User’s Guide Editing Passwords Deleting the Entire Password Directory Deleting Passwords Dial Back Function Dial Back Example System Parameters MenuUser Account Parameters Network Parameters Network Parameters Menu Network Parameters Telnet ParametersWEB Server Telnet Parameters Web ServerMAC Address IP Security IP Security Feature Conﬁ guration Telnet Port Parameters 12 The Telnet Port Parameters Menu Text Interface Telnet Port Parameters CMS-6R4 Series User’s Guide Conﬁ guration Invalid Access Lockout Feature 3. RS232 Port Parameters 14 Port Parameters Menu Web Browser Interface Conﬁ guration CMS-6R4 Series User’s Guide Conﬁ guration CMS-6R4 Series User’s Guide 3.1. RS232 Port Modes Copy Serial Port Parameters Copying Parameters to Several Ports Conﬁ guration Text Interface Type /P 7 and press Enter Configuring the Internal Modem Plug Parameters Menus Plug #1 Parameters 17 Plug Parameters Menu Web Browser Interface Reboot Cycles Boot / Sequence Delay Period Save Configuration Parameters Operation Operation via the Web Browser InterfaceStatus Screen Web Browser Interface Status Menu Web Browser Interface DPL Operation via the Text Interface Status Screen Text Interface Port Name CMD Access On 1 or /ON Router Switching Outlets Text Interface Applying Commands to Several Outlets Text Interface BO * EnterConnections Between RS232 Ports Text Interface Connecting Ports Three Characters Uses the format EnterLLLEnter, where Disconnecting Ports Enter CMS-6R4 Series User’s Guide Server Enter Defining Hunt Groups Hunt Group Example Any-to-Any ModePassive Mode Port Modes Reading Data from Buffer Mode Ports Buffer Mode Port Buffers Modem Mode Automated Mode Logging Out of Command Mode Operation Standard Telnet Protocol and Raw Socket Mode Direct Connect Feature Direct Connect Configuration Connection Example Connecting to a Serial Port using Direct Connect Terminating a Direct Connect Session Manual Operation Status Screens Main Status Screen /SPort Section Main Status Screen Plug Section Network Status Screen /SN RTS Port Diagnostics Screen /SDPort Diagnostics Name Status Baud COM HS Mode CTS RTS/CTS Port Parameters Screen /WPort Parameters Screen Serial Ports Port Parameters #3 Port Parameters Screen Network Port Shown Port Parameters Screen Network Port Super User Directory CMS-6R4 Series User’s Guide Sending Parameters to a File Saving and Restoring Configuration Parameters Restoring Saved Parameters Upgrading the CMS-6R4 Firmware CMS-6R4 Series User’s Guide Command Reference Guide Command Conventions10-1 10-2 Command Summary 10-3 Command Response Messages 10-4 Command SetInitiate Boot Cycle Response 10-5 ConnectFormat /C x x Enter Terse Copy RS232 Port Parameters Third Party Disconnect10-6 Format /E,Y x x Enter Set Plugs to Default StateFormat /DPL,Y Enter Erase Buffer 10-8 Set to Factory DefaultsSet System Parameters Help 10-9 Reset Network InterfaceDisplay Site ID Set Network Port Parameters Switch Plugs Off Format /OFF,Y n Enter or /OF,Y Enter10-10 Switch Plugs on Set RS232 Port Parameters10-11 10-12 Display Port DiagnosticsSet Plug Parameters Display Main Status Screen Send Parameters to a File Upgrade FirmwareDisplay Network Status Telnet Telnet Connection Out 10-14 Unlock Port Invalid Access LockoutView Password Directory Display Port Parameters Who Resident Disconnect Sequence Exit Command ModeFormat Default Response Format /X,Y Enter 10-16 Interface Description Serial RS232 Port InterfaceApx-1 Apx-2 Specifications Apx-3 Customer Service Apx-4 Trademark and Copyright Information Index-1 Index Index-2 Index Index-3 Index-4