Restoring Saved Parameters | I-Tech Company CMS 6R4 Series instruction

CMS-6R4 Series - User’s Guide

8.2. Restoring Saved Parameters

This Section describes the procedure for using your communications program to send saved parameters to the CMS-6R4.

Notes:

•Parameters saved to an ASCII ﬁle can only be restored via the Text Interface. This procedure cannot be performed via the Web Browser Interface.

•Note that the "Restore Parameters" feature is only available when the Supervisor Mode is active.

1.Start your communications program and access the CMS-6R4 command mode via the Text Interface as described in Section 5.2.2.

2.If the Password Prompt is displayed, key in a password that permits access to Supervisor Level commands, and then press [Enter].

3.Conﬁgure your communications program to upload an ASCII text ﬁle.

4.Upload the ﬁle with the saved parameters. If necessary, key in the ﬁle name and directory path.

5.When the upload is complete, make certain to terminate the communications program’s upload mode.

Note:

•The current On/Off status of each CMS-6R4 plug will not be saved or restored.

•When the conﬁguration ﬁle is sent to the CMS-6R4 via telnet, the unit’s IP Address, Subnet Mask, and Gateway Address will not be changed until after you exit from command mode.

At this point, saved parameters should have been restored to the CMS-6R4 unit. Check the conﬁguration menus and status screens to make certain that saved parameters have been correctly restored.

8-2

Image 96

I-Tech Company CMS 6R4 Series manual Restoring Saved Parameters

Contents

Distributed by Page Installation Instructions FCC Part 15 Regulation Table of Contents Upgrading the CMS-6R4 Firmware Command Reference Guide List of Figures CMS-6R4 Series User’s Guide Security Features and Co-Location Features Easy to Configure, Easy to UseIntroduction CMS-6R4 and CMS-6R4 CE Models Typographic Conventions Unit Description Front Panel Components Back Panel Components Back Panel Components 120 VAC Model Shown Unit Description CMS-6R4 Series User’s Guide Hardware Installation Apply Power to the CMS-6R4Quick Start Connect your PC to the CMS-6R4 Communicating with the CMS-6R4 Text Interface Port Name CMD Access Status Mode Status DefaultPlug Name Connecting Ports and Switching Outlets Quick Start CMS-6R4 Series User’s Guide Installation Power Supply ConnectionConnecting Devices to the Switched Outlets Installing the Cable Keeper Connecting Devices to the RS232 Serial Ports Connecting Control Devices to the CMS-6R4Connecting the Network Cable Control via Local PC Configuration Supervisor Mode and Non-Supervisor Mode Communicating with the CMS-6R4 Accessing the Web Browser Interface Main Status Screen Web Browser Interface Sample Values Shown Accessing the Text Interface Plug Name BOOT/SEQ Delay Status DefaultCMS-6R4 Port Name System SetUp Port $ telnet 192.168.168.168 Enter Password Functions Configuration Menus System Parameters Menu System Parameters Menu Web Browser Interface System Parameters Conﬁ guration Password Directory Password Directory Menu Web Browser Interface Edit Password Directory Adding Passwords ADD NAME/PASSWORD ESC CMS-6R4 Series User’s Guide Editing Passwords Deleting Passwords Deleting the Entire Password Directory Dial Back Function Dial Back Example System Parameters MenuUser Account Parameters Network Parameters Menu Network Parameters Network Parameters Telnet ParametersWEB Server Telnet Parameters Web ServerMAC Address IP Security Feature IP Security Conﬁ guration 12 The Telnet Port Parameters Menu Text Interface Telnet Port Parameters Telnet Port Parameters CMS-6R4 Series User’s Guide Conﬁ guration Invalid Access Lockout Feature 3. RS232 Port Parameters 14 Port Parameters Menu Web Browser Interface Conﬁ guration CMS-6R4 Series User’s Guide Conﬁ guration CMS-6R4 Series User’s Guide 3.1. RS232 Port Modes Copying Parameters to Several Ports Copy Serial Port Parameters Conﬁ guration Configuring the Internal Modem Text Interface Type /P 7 and press Enter Plug Parameters Menus 17 Plug Parameters Menu Web Browser Interface Plug #1 Parameters Boot / Sequence Delay Period Reboot Cycles Save Configuration Parameters Operation Operation via the Web Browser InterfaceStatus Screen Web Browser Interface Status Menu Web Browser Interface Operation via the Text Interface DPL Port Name CMD Access Status Screen Text Interface Switching Outlets Text Interface On 1 or /ON Router Applying Commands to Several Outlets Text Interface BO * EnterConnections Between RS232 Ports Text Interface Connecting Ports Disconnecting Ports Three Characters Uses the format EnterLLLEnter, where Enter CMS-6R4 Series User’s Guide Defining Hunt Groups Server Enter Any-to-Any Mode Passive ModePort Modes Hunt Group Example Buffer Mode Reading Data from Buffer Mode Ports Port Buffers Modem Mode Logging Out of Command Mode Automated Mode Operation Direct Connect Feature Standard Telnet Protocol and Raw Socket Mode Direct Connect Configuration Connecting to a Serial Port using Direct Connect Connection Example Terminating a Direct Connect Session Manual Operation Status Screens Main Status Screen /SPort Section Plug Section Main Status Screen Network Status Screen /SN Port Diagnostics Screen /SD Port Diagnostics Name Status Baud COM HS ModeCTS RTS Port Parameters Screen /W Port Parameters Screen Serial PortsPort Parameters #3 RTS/CTS Port Parameters Screen Network Port Port Parameters Screen Network Port Shown User Directory Super CMS-6R4 Series User’s Guide Saving and Restoring Configuration Parameters Sending Parameters to a File Restoring Saved Parameters Upgrading the CMS-6R4 Firmware CMS-6R4 Series User’s Guide Command Reference Guide Command Conventions10-1 Command Summary 10-2 Command Response Messages 10-3 Command Set Initiate Boot CycleResponse 10-4 Connect Format /C x x EnterTerse 10-5 Copy RS232 Port Parameters Third Party Disconnect10-6 Set Plugs to Default State Format /DPL,Y EnterErase Buffer Format /E,Y x x Enter Set to Factory Defaults Set System ParametersHelp 10-8 Reset Network Interface Display Site IDSet Network Port Parameters 10-9 Switch Plugs Off Format /OFF,Y n Enter or /OF,Y Enter10-10 Switch Plugs on Set RS232 Port Parameters10-11 Display Port Diagnostics Set Plug ParametersDisplay Main Status Screen 10-12 Upgrade Firmware Display Network StatusTelnet Telnet Connection Out Send Parameters to a File Unlock Port Invalid Access Lockout View Password DirectoryDisplay Port Parameters Who 10-14 Exit Command Mode Format Default ResponseFormat /X,Y Enter Resident Disconnect Sequence 10-16 Interface Description Serial RS232 Port InterfaceApx-1 Specifications Apx-2 Customer Service Apx-3 Trademark and Copyright Information Apx-4 Index Index-1 Index-2 Index-3 Index Index-4