CPX-1000 Shelf, System Alarm Panel | Paradyne guide

2. CPX-1000 Voice Services Platform Description	1000-A2-GN22-00

CPX-1000 Shelf

Each CPX shelf is 12 RU (21 inches) high and 17 inches deep. The shelf can mount in either a 19-inch Electronic Industries Association (EIA) rack or a 23-inch rack.

The CPX shelf is a forced-air cooled Network Equipment Building Standard (NEBS) Level 3-compliant platform with:

16-slot midplane

DC power input panel

Alarm panel

Three hot-swappable power supplies

System Alarm Panel

The midplane is the interconnect for all 16 slots, power distribution, and alarm signal distribution. The CPX midplane accepts line cards, processing modules, and rear mounted transition modules.

The power supplies (including integral fan assemblies) are located below the card cage (accessible from the front of the shelf).

The CPX alarm panel is located on the top front of the shelf. Indicators display the current operating status of the shelf and an alarm connector outputs to remote Telco alarm equipment (Figure 2–5). The CPX includes three types of indicators:

Slot Status indicators for all 16 slots

System Status indicator for system status

Telco alarms

Table 2–1lists the description and status of each group.

System Status Indicators

Telco Alarm Indicators

Alarm Panel

	SYSTEM ALERTS			TELCO
ALERT A	ALERT B	ALERT C	MINOR	MAJOR	CRITICAL	ALARM

DISABLED

DISABLED

DISABLED

DISABLED

DISABLED

DISABLED

DISABLED

DISABLED

DISABLED

DISABLED

DISABLED

DISABLED

DISABLED

DISABLED

DISABLED

DISABLED

UNLOCKED

UNLOCKED

UNLOCKED

UNLOCKED

UNLOCKED

UNLOCKED

UNLOCKED

UNLOCKED

UNLOCKED

UNLOCKED

UNLOCKED

UNLOCKED

UNLOCKED

UNLOCKED

UNLOCKED

UNLOCKED

ACT 1

ACT 2

ACT 3

ACT 4

ACT 5

ACT 6

ACT 7

ACT 8

ACT 9

ACT 10

ACT 11

ACT 12

ACT13

ACT14

ACT 15

ACT 16

0233-01

Slot Status Indicators

Figure 2–5. System Alarm Panel

2-10	February 2003

Image 34

Paradyne manual CPX-1000 Shelf, System Alarm Panel

Contents

Jetstream CPX-1000 Voice Services Platform Copyright 2003 Paradyne Corporation All rights reserved United States EMI Notice Canada EMI Notice Table of Contents Installing the CPX-1000 1000-A2-GN22-00Table of Contents Troubleshooting Appendix a Using the Console Appendix B Pin Assignments and Indicators Preface Audience Provides useful information to help you install the CPX Related Documents Conventions Class 1 Laser Preface 1000-A2-GN22-00 February Land line copper loops by using ATM over Mmds or U-NII Local Access Network ArchitectureVoice over Wireless VoWLL-eliminates the need for Wireless broadband access networks VoBB Local Access Networks CPX-1000 Voice Services Platform Packet Network Configuration Bandwidth Usage-768 kbps Sdsl Circuit Call Origination and Completion Subscriber Initiates a Call Subscriber Receives a Call CPX-1000 Calling Features CPX-1000 Management Tools and APIs Voice-over-Broadband Networking 1000-A2-GN22-00 February CPX-1000 Voice Services Platform Description CPX-1000 Front View Equipment Operational Features Traffic Capacity Concentration management-supports line CPX-1000 Operation CPX Functional Diagram T1 Interface CPX Functional Diagram STS-1 Interface Management Processing Call Processing Pstn Interface 1000-A2-GN22-00 1000-A2-GN22-00 February CPX-1000 Front and Rear Views System Alarm Panel CPX-1000 Shelf Remote Alarm Connector Alarm Indicator Status and DescriptionSlot Status System Status Telco Status Line Modules with T1 Line Modules with STS-1 Call Processor Modules Call Processor Module CP Module Controls, Indicators, and Ports Passes all this information to the management system CPX supports redundant CP modules FigureModule and can take over at any time Voice/Data Interruptionœ possible Management Processor Module Management Processor Module MP Module Controls, Indicators, and Ports CPX-1000 Voice Services Platform Description 1000-A2-GN22-00 T1 Module Path Protection Switching 11. Octal T1 and Transition Cards Octal T1 Module Controls, Indicators, and Ports Port T1 Ecac Module 12 -port T1 Ecac and T1 Transition Cards Port T1 Ecac Module Controls, Indicators, and Ports STS-1 Module STS-1 Card STS-1 Transition Card STS-1 Module Controls, Indicators, and Ports STS-1 Ecac Card STS-1 Ecac Processing Card -controls the 28 DS1s Hot swap. Unlit when card is locked STS-1 Ecac Module Controls, Indicators, and PortsLights blue when card is ready for STS-1 Splitter Assembly for STS-1 15. STS-1 Transition Card to Splitter Assembly Connections To Net STS-1 Splitter ConnectionsFrom Net ATM OC-3 Module 10.ATM OC-3 Module Controls, Indicators, and Ports OC-3 ATM module includes the processing card only 16. ATM OC-3 Module Echo Cancellation Module 17. Echo Cancellation Module Echo Cancellation Compression Module Ecac 18. Echo Cancellation And Compression Card DC Power Supply Fan Fan Modules 19. DC Power Supply/Fan Modules 20. Shelf Airflow DC Power Distribution Panel 21. Power Distribution PanelPage Installing the CPX-1000 Installation Checklist 1000-A2-GN22-00 Installing the CPX-1000 Turn-up Checklist Check the bit error rate BER on every GR-303 Pstn line Installation Requirements Safety Requirements General Safety Precautions Shelf Front Shelf Rear ESD Wrist Strap Grounding Jack Aisle Requirements Environmental Requirements Requirements PowerRack 1000-A2-GN22-00 Installing the CPX-1000 Unpack Inspect CPX-1000 Cut the shipping bands and remove the top of the box Inspect the CPX for damage Inventory CPX ComponentsInto the bottom box lid Document Mounting Flanges in 23 Configuration Attach Mounting Flanges Rack Mount the CPX Splitter Assembly Front of the shelf Shelf for optional STS-1 Splitter Assembly above each unitReinstall the power supply/fan modules 24 1 2-inch pan head screws to fasten the shelf to the rack Mount Splitter Assembly Connect Plant Battery Frame Ground Compression lug with two #10 screw holes Terminate a #6 AWG frame ground wire in an LCC or LCDTo rack ground Or larger, stranded or solid wires terminated in #10 size Remove the cover from the plant battery terminal stripVDC a and B outputs of the power source using two 14 AWG If you use 14 AWG wire, be sure that the plant battery Install Modules in CPX CPX Front-12-port T1 Ecac and OC-3 ATM Modules CPX Front-OC-3 ATM and STS-ECAC Modules Installing Additional Cards Verify Hardware Installation Attach OC-3 ATM Cables Remove the dust cover from the ATM fiber-optic SC connectorATM fiber-optic SC connector sockets To attach OC-3 cables to the CPX Attach MP Card to CP Cards Attach Ethernet CablesAttach CP Redundancy Cable Connect the CPX to the LAN Attach the T-1/ DS-1 Cables Attaching Cables to Octal T1 Modules Dress the T1 and power cables from the rear of the shelf, so Octal T1 Transition Card Cabling Attaching Cables to 12-Port T1 Modules Punch downeachT1 circuitontheback of the RJ-48C patch panel To Net Transmit STS-1 cable to Pstn Attach the STS-1 CablesSTS-1 Cable ConnectionsΩ From Net Receive STS-1 cable to Pstn Transition module replacement From NET connectors of the STS-1 Splitter AssemblyConnectors on the Class 5 switch Primary and corresponding standby transition modules Apply Power Verify Cabling ATM Module OC-3 Indicators Verify that the Status Check Plug-in Module IndicatorsSTS-1 Ecac Module Indicators Verify that the Stat and ACT Echo Cancellation and Compression Module Indicators Alarm Panel IndicatorsEcho Cancellation Indicators Verify that the Hot Swap Check the Fans Verify CPX LAN Provision the CPX-1000Connection Installing the CPX-1000 1000-A2-GN22-00 February Component-level troubleshooting-includes TroubleshootingSystem-level troubleshooting-includes alarms Failed modules Approach the problem systematically Whether you Work from the general specific start with simple System Trouble Shooting Using JetCraft Alarm Window CPX Shelf Telco Status Indicators ATM Ports Loss of signal or loss of frame section IAD configuration errorLost link with IAD Remote failure indication line Module TroubleshootingNormal Activity Indicator Usage Provisioned compression schemes not supported CP Module Troubleshooting Refer to -4when troubleshooting the CP modulePWR indicator is off MP Module Troubleshooting Ethernet green MP-to-LAN interface is VDC from the plant battery Pstn Module TroubleshootingVerify that the CPX is receiving After the system is initialized, verify Indicator is offThat the T1/STS-1 module blue Tx and/or Rx indicators are off ATM Module TroubleshootingEthernet LAN Troubleshooting 9for troubleshooting instructions Power System TroubleshootingFans are off, see Troubleshooting Instructions Table Depending on the number of Pstn and ATM modules Power Failure TroubleshootingCPX may take several minutes to initialize Module type and refer to the appropriate table for action Loopbacks Recommended Power Off Repair ProceduresEmergency Power-Off Inoperative Power Supply Fan Module RemovalReplacing Fans Fan, or the power supply module may overheat Install PowerSupply/Fan Module Alarm Panel Removing the Alarm Panel Removing Power Distribution Panel PowerInstalling the Alarm Panel Distribution You do not need to remove the power supplies when To install the power distribution panelWhen replacing a DC Power Distribution Panel, replace Installing a Power Distribution Panel, although backing Module Removal Installation Shelf Front Shelf Rear ESD Wrist Strap Grounding Jack Removing Replacing Cards Hot Swapping an MP Card Hot Swapping CP and HSC Cards Hot Swapping Line Cards An unplanned hot swap involves the removal and replacement Place, using the card ejectorsUnlocked, and all resources for that card are restored Lock them in place, using the card ejectors Hot Growth Repair Procedures 1000-A2-GN22-00 February Using the Console Logging Enter the user or admin name and password Figure A-1 Or 6050 for CP-B. The Console window appears Or admin. Figure A-2 shows a sample listing Figure A-2. a Sample Listing of Console Commands Console Commands Displays command summary or usage information Admin type ? and the following screen appearsKey to gathering Telnet info is the ? Cpx help command name-Displays detailed help on Displays a command summary or usage informationCpx help-Displays a summary of all commands available Cpx command-namehelp-Displays detailed help on Shows which CCS and EOC links are currently active Displays information the specified portLists all ATM portgroups Displays information about Pstn protection groups Sets or shows the status of the chassis fan speeds Admin Console CommandsClears statistics for the component specified Where Cpx setcdv-Displays current Cell Delay Variation Reboots the CPDisplays/sets ATM Cell Delay Variation CDV Cpx setcdv newcdv-Sets a new Cell Delay Variation That same T1 card Sets the DS1 line length or Line Build Out LBOTap/monitor H.110 time slots Displays active voice path information Pin Assignments and Indicators ATM network DBmCPX-1000 and the external Line coding Clock DS-1 Rcv span Defaults to internal if Rcv fails Abam Tx + to LAN Tx to LAN Rx + from LAN Table B-2. Ethernet LAN Jack Pin AssignmentsNot connected Rx Ring Rx Tip Not connected Tx Tip Table B-3. T1 Transition Module Pin AssignmentsTx Ring Not connected Table B-4. RJ21X Pin Assignments T1 Circuit System Alarm Connection Requirements Table B-5. Remote Alarm Connector Pin Assignments Table B-6. T1 Transition Module Pin Assignments Table B-7. Ethernet LAN Jack Pin Assignments Replacement Parts 1000-F1-203 1000-F1-202Hot Swap Controller Card for HA system processing card Management Processor Module for HA system processing Specifications GR-63-CORE Table D-1. CPX-1000 Physical Specifications Table D-2. CPX-1000 Environmental Specifications Table D-3. CPX-1000 Electrical Specifications UL, CSA,VDE Certified T1/DS-1 Rcv defaults to internal if Rcv fails Table D-4. CPX-1000 Electronic Specifications50 ft., 50-450 ft Physical interface Termination High Table D-5. CPX-1000 Operating SpecificationsTable D-6. STS-1 Splitter Assembly Physical Specifications Lbs Specifications 1000-A2-GN22-00 February Index Numerics Index 1000-A2-GN22-00 1000-A2-GN22-00 Index T1 connections 3-26,3-29,3-30,B-2