CPX Functional Diagram T1 Interface | Paradyne CPX-1000 specs

	2. CPX-1000 Voice Services Platform Description			1000-A2-GN22-00
	MP Module			CPX-1000
	MP Module			Shelf
				Shelf
	EOC		Management
	Process		Process
	CP		Call
	Modules		Call
			Processing
			Engine
			TMC	IAD
			TMC	Signalling and
			Processing	Signalling and
			Processing	Connectivity
				Connectivity
		PSTN Interface	Packet Interface
		T1 Modules	ATM Modules
	Q.931 (LAPD) Link Layer
			Voice Bus	Control
			Voice Bus
	Control	Voice	Voice	Voice/
	Control			Control
				Control
			Echo	Splitter
			Cancellation	Splitter
			Cancellation
			and
		Compression
	T1 Interface Controller			OC3 Port
				0481

Figure 2–2. CPX Functional Diagram (T1 Interface)

2-4	February 2003

Image 28

Paradyne CPX-1000 manual CPX Functional Diagram T1 Interface

Contents

Jetstream CPX-1000 Voice Services Platform Copyright 2003 Paradyne Corporation All rights reserved United States EMI Notice Canada EMI Notice Table of Contents Installing the CPX-1000 1000-A2-GN22-00Table of Contents Troubleshooting Appendix a Using the Console Appendix B Pin Assignments and Indicators Preface Audience Provides useful information to help you install the CPX Related Documents Conventions Class 1 Laser Preface 1000-A2-GN22-00 February Local Access Network Architecture Voice over Wireless VoWLL-eliminates the need forLand line copper loops by using ATM over Mmds or U-NII Wireless broadband access networks VoBB Local Access Networks CPX-1000 Voice Services Platform Packet Network Configuration Bandwidth Usage-768 kbps Sdsl Circuit Call Origination and Completion Subscriber Initiates a Call Subscriber Receives a Call CPX-1000 Calling Features CPX-1000 Management Tools and APIs Voice-over-Broadband Networking 1000-A2-GN22-00 February CPX-1000 Voice Services Platform Description CPX-1000 Front View Equipment Operational Features Traffic Capacity Concentration management-supports line CPX-1000 Operation CPX Functional Diagram T1 Interface CPX Functional Diagram STS-1 Interface Management Processing Call Processing Pstn Interface 1000-A2-GN22-00 1000-A2-GN22-00 February CPX-1000 Front and Rear Views System Alarm Panel CPX-1000 Shelf Remote Alarm Connector Alarm Indicator Status and DescriptionSlot Status System Status Telco Status Line Modules with T1 Line Modules with STS-1 Call Processor Modules Call Processor Module CP Module Controls, Indicators, and Ports Passes all this information to the management system CPX supports redundant CP modules FigureModule and can take over at any time Voice/Data Interruptionœ possible Management Processor Module Management Processor Module MP Module Controls, Indicators, and Ports CPX-1000 Voice Services Platform Description 1000-A2-GN22-00 T1 Module Path Protection Switching 11. Octal T1 and Transition Cards Octal T1 Module Controls, Indicators, and Ports Port T1 Ecac Module 12 -port T1 Ecac and T1 Transition Cards Port T1 Ecac Module Controls, Indicators, and Ports STS-1 Module STS-1 Card STS-1 Transition Card STS-1 Module Controls, Indicators, and Ports STS-1 Ecac Card STS-1 Ecac Processing Card -controls the 28 DS1s STS-1 Ecac Module Controls, Indicators, and Ports Lights blue when card is ready forHot swap. Unlit when card is locked STS-1 Splitter Assembly for STS-1 15. STS-1 Transition Card to Splitter Assembly Connections To Net STS-1 Splitter ConnectionsFrom Net ATM OC-3 Module 10.ATM OC-3 Module Controls, Indicators, and Ports OC-3 ATM module includes the processing card only 16. ATM OC-3 Module Echo Cancellation Module 17. Echo Cancellation Module Echo Cancellation Compression Module Ecac 18. Echo Cancellation And Compression Card DC Power Supply Fan Fan Modules 19. DC Power Supply/Fan Modules 20. Shelf Airflow DC Power Distribution Panel 21. Power Distribution PanelPage Installing the CPX-1000 Installation Checklist 1000-A2-GN22-00 Installing the CPX-1000 Turn-up Checklist Check the bit error rate BER on every GR-303 Pstn line Installation Requirements Safety Requirements General Safety Precautions Shelf Front Shelf Rear ESD Wrist Strap Grounding Jack Aisle Requirements Environmental Requirements Requirements PowerRack 1000-A2-GN22-00 Installing the CPX-1000 Unpack Inspect CPX-1000 Cut the shipping bands and remove the top of the box Inventory CPX Components Into the bottom box lidInspect the CPX for damage Document Mounting Flanges in 23 Configuration Attach Mounting Flanges Rack Mount the CPX Splitter Assembly Shelf for optional STS-1 Splitter Assembly above each unit Reinstall the power supply/fan modulesFront of the shelf 24 1 2-inch pan head screws to fasten the shelf to the rack Mount Splitter Assembly Connect Plant Battery Frame Ground Compression lug with two #10 screw holes Terminate a #6 AWG frame ground wire in an LCC or LCDTo rack ground Remove the cover from the plant battery terminal strip VDC a and B outputs of the power source using two 14 AWGOr larger, stranded or solid wires terminated in #10 size If you use 14 AWG wire, be sure that the plant battery Install Modules in CPX CPX Front-12-port T1 Ecac and OC-3 ATM Modules CPX Front-OC-3 ATM and STS-ECAC Modules Installing Additional Cards Verify Hardware Installation Remove the dust cover from the ATM fiber-optic SC connector ATM fiber-optic SC connector socketsAttach OC-3 ATM Cables To attach OC-3 cables to the CPX Attach Ethernet Cables Attach CP Redundancy CableAttach MP Card to CP Cards Connect the CPX to the LAN Attach the T-1/ DS-1 Cables Attaching Cables to Octal T1 Modules Dress the T1 and power cables from the rear of the shelf, so Octal T1 Transition Card Cabling Attaching Cables to 12-Port T1 Modules Punch downeachT1 circuitontheback of the RJ-48C patch panel Attach the STS-1 Cables STS-1 Cable ConnectionsΩTo Net Transmit STS-1 cable to Pstn From Net Receive STS-1 cable to Pstn From NET connectors of the STS-1 Splitter Assembly Connectors on the Class 5 switchTransition module replacement Primary and corresponding standby transition modules Apply Power Verify Cabling ATM Module OC-3 Indicators Verify that the Status Check Plug-in Module IndicatorsSTS-1 Ecac Module Indicators Verify that the Stat and ACT Alarm Panel Indicators Echo Cancellation Indicators Verify that the Hot SwapEcho Cancellation and Compression Module Indicators Check the Fans Verify CPX LAN Provision the CPX-1000Connection Installing the CPX-1000 1000-A2-GN22-00 February Troubleshooting System-level troubleshooting-includes alarmsComponent-level troubleshooting-includes Failed modules Approach the problem systematically Whether you Work from the general specific start with simple System Trouble Shooting Using JetCraft Alarm Window CPX Shelf Telco Status Indicators ATM Ports Loss of signal or loss of frame section IAD configuration errorLost link with IAD Module Troubleshooting Normal Activity Indicator UsageRemote failure indication line Provisioned compression schemes not supported CP Module Troubleshooting Refer to -4when troubleshooting the CP modulePWR indicator is off MP Module Troubleshooting Ethernet green MP-to-LAN interface is VDC from the plant battery Pstn Module TroubleshootingVerify that the CPX is receiving After the system is initialized, verify Indicator is offThat the T1/STS-1 module blue Tx and/or Rx indicators are off ATM Module TroubleshootingEthernet LAN Troubleshooting 9for troubleshooting instructions Power System TroubleshootingFans are off, see Troubleshooting Instructions Table Power Failure Troubleshooting CPX may take several minutes to initializeDepending on the number of Pstn and ATM modules Module type and refer to the appropriate table for action Loopbacks Recommended Power Off Repair ProceduresEmergency Power-Off Power Supply Fan Module Removal ReplacingInoperative Fans Fan, or the power supply module may overheat Install PowerSupply/Fan Module Alarm Panel Removing the Alarm Panel Power Installing the Alarm PanelRemoving Power Distribution Panel Distribution To install the power distribution panel When replacing a DC Power Distribution Panel, replaceYou do not need to remove the power supplies when Installing a Power Distribution Panel, although backing Module Removal Installation Shelf Front Shelf Rear ESD Wrist Strap Grounding Jack Removing Replacing Cards Hot Swapping an MP Card Hot Swapping CP and HSC Cards Hot Swapping Line Cards Place, using the card ejectors Unlocked, and all resources for that card are restoredAn unplanned hot swap involves the removal and replacement Lock them in place, using the card ejectors Hot Growth Repair Procedures 1000-A2-GN22-00 February Using the Console Logging Enter the user or admin name and password Figure A-1 Or 6050 for CP-B. The Console window appears Or admin. Figure A-2 shows a sample listing Figure A-2. a Sample Listing of Console Commands Console Commands Displays command summary or usage information Admin type ? and the following screen appearsKey to gathering Telnet info is the ? Displays a command summary or usage information Cpx help-Displays a summary of all commands availableCpx help command name-Displays detailed help on Cpx command-namehelp-Displays detailed help on Displays information the specified port Lists all ATM portgroupsShows which CCS and EOC links are currently active Displays information about Pstn protection groups Admin Console Commands Clears statistics for the component specifiedSets or shows the status of the chassis fan speeds Where Reboots the CP Displays/sets ATM Cell Delay Variation CDVCpx setcdv-Displays current Cell Delay Variation Cpx setcdv newcdv-Sets a new Cell Delay Variation Sets the DS1 line length or Line Build Out LBO Tap/monitor H.110 time slotsThat same T1 card Displays active voice path information Pin Assignments and Indicators DBm CPX-1000 and the externalATM network Line coding Clock DS-1 Rcv span Defaults to internal if Rcv fails Abam Tx + to LAN Tx to LAN Rx + from LAN Table B-2. Ethernet LAN Jack Pin AssignmentsNot connected Rx Ring Rx Tip Not connected Tx Tip Table B-3. T1 Transition Module Pin AssignmentsTx Ring Not connected Table B-4. RJ21X Pin Assignments T1 Circuit System Alarm Connection Requirements Table B-5. Remote Alarm Connector Pin Assignments Table B-6. T1 Transition Module Pin Assignments Table B-7. Ethernet LAN Jack Pin Assignments Replacement Parts 1000-F1-202 Hot Swap Controller Card for HA system processing card1000-F1-203 Management Processor Module for HA system processing Specifications GR-63-CORE Table D-1. CPX-1000 Physical Specifications Table D-2. CPX-1000 Environmental Specifications Table D-3. CPX-1000 Electrical Specifications UL, CSA,VDE Certified T1/DS-1 Rcv defaults to internal if Rcv fails Table D-4. CPX-1000 Electronic Specifications50 ft., 50-450 ft Physical interface Termination Table D-5. CPX-1000 Operating Specifications Table D-6. STS-1 Splitter Assembly Physical SpecificationsHigh Lbs Specifications 1000-A2-GN22-00 February Index Numerics Index 1000-A2-GN22-00 1000-A2-GN22-00 Index T1 connections 3-26,3-29,3-30,B-2