Paradyne CPX-1000 Attach Ethernet Cables, Attach CP Redundancy Cable, Attach MP Card to CP Cards

1000-A2-GN22-00 3. Installing the CPX-1000

Attach

Ethernet

Cables

Connect the MP module to the CP modules via Ethernet. You can also connect the CPX shelf to an Ethernet LAN for access via remote system management.

Attach CP Redundancy cables here

Management	Call		ATM OC-3
Processor	Processor	12-Port T1
Port T1 Module	Module Sets ECAC		Modules
ECAC		Modules

Attach CPX to LAN here

TDM-12E1/T1		TDM-12E1/T1		TDM-12E1/T1		TDM-12E1/T1		TDM-12E1/T1						CP2				CP2		TDM-12E1/T1		TDM-12E1/T1
														1				1
													PCI				PCI
													MEZZANINE	LNK	ACT	PWR	MEZZANINE	LNK	ACT	PWR
												P
												M		2		ERROR		2		ERROR								Attach
												C
												2	CARD				CARD							Status	Status	Status	Status
																								Tx	Tx	Tx	Tx
														LNK	ACT			LNK	ACT
														10/100				10/100						Rx	Rx	Rx	Rx
														ETHERNET				ETHERNET										MP to CP
											1		10/100 BASE T				10/100 BASE T
										LNK	ACT		COM 1				COM 1											cables here
S	A	S	A	S	A	S	A	S	A			P								S	A	S	A
T		T		T		T		T				M								T		T
A	C	A	C	A	C	A	C	A	C											A	C	A	C
T	T	T	T	T	T	T	T	T	T		2	C								T	T	T	T
1	2	1	2	1	2	1	2	1	2			1								1	2	1	2
3	4	3	4	3	4	3	4	3	4											3	4	3	4
5	6	5	6	5	6	5	6	5	6	LNK	ACT			RST				RST		5	6	5	6
7	8	7	8		8	7	8	7	8	10/100										7	8	7	8
										ETHERNET				ABT				ABT						ATM 155	ATM 155	ATM 155	ATM 155
9	10	9	10	9	10	9	10	9	10											9	10	9	10
11	12	11	12	11	12	11	12	11	12	ETHERNET				BFL	CPU			BFL	CPU	11	12	11	12
														CPCI	PCI			CPCI	PCI
										COM 1			USB 1				USB 1
HOT		HOT		HOT		HOT		HOT		RESET			USB 0				USB 0			HOT		HOT
SWAP		SWAP		SWAP		SWAP		SWAP		EXT	PWR									SWAP		SWAP
	1	2		3		4		5		6				7		8		9		10	11	12		13	14	15	16

Attach MP Card to CP Cards

Step 1

Connect the CPX to the LAN

Step 1

Step 2

Attach CP

Redundancy

Cable

To establish a communication link on a shelf with either a T1 or STS-1 configuration:

Connect the Ethernet ports on the MP module (at the front shelf) to the Ethernet ports on the CP A and the CP B card respectively, using the cables provided (Octal T1 card shown).

To connect the CPX to an Ethernet LAN:

Plug a CAT-5 straight-through cable into the RJ-45 Ethernet port of the Management Processor (MP) Transition card.

Connect the other end of the cable to the LAN hub or router

To establish redundancy on the CPX with either a T1 (Octal or 12-port) or STS-1 (without ECAC, or STS-1 with ECAC) configuration, connect the two CP cards (at the front shelf) using the cable provided.

February 2003 3-25