Station Statistics, 127 | Proxim AP-700 specification

Monitoring

AP-700 User Guide

Station Statistics

Station Statistics

This tab displays information on wireless clients attached to the AP and on Wireless Distribution System links.

Enable the Monitoring Station Statistics feature (Station Statistics are disabled by default) by checking Enable Monitoring Station Statistics and click OK.

You do not need to reboot the AP for the changes to take effect. If clients are connected to the device or WDS links are configured for the device, the statistics will now be shown on the screen.

Click on the Refresh button in the browser window to view the latest statistics. If any new clients associate to the AP, you can see the statistics of the new clients after you click the refresh button.

Figure 5-9 Station Statistics Monitoring Tab

Description of Station Statistics

The following stations statistics are displayed:

•MAC Address: The MAC address of the wireless client for which the statistics are gathered. For WDS links, this is the partner MAC address of the link.

•IP Address: The IP address of the associated wireless station for which the Statistics are gathered. (0.0.0.0 for WDS links)

•Interface to which the Station is connected: The interface number on which the client is connected with the AP. For WDS links this is the interface on which the link is configured.

•Station Type: The type of wireless client (STA or WDS).

•MAC Protocol: The MAC protocol for this wireless client (or WDS link partner). The possible values are 802.11a, 802.11b, 802.11g

•Signal / Noise: The Signal /Noise Level measured at the AP when frames are received from the associated wireless station (or WDS link partner)

•Time since Last Packet Received: The time elapsed since the last frame from the associated wireless station (or WDS link partner) was received.

127

Image 127

Proxim AP-700 manual Station Statistics, 127

Contents

ORiNOCO AP-700 Access Point User Guide AP-700 User Guide CopyrightTrademarks OpenSSL License Note Contents Management Contents AP-700 User Guide Troubleshooting CommandsMonitoring General Notes Command Line Interface CLI Regulatory Compliance Ascii Character Chart C SpecificationsStatement of Warranty Technical Support AP-700 User Guide Introduction Introduction to Wireless NetworkingDocument Conventions Guidelines for Roaming Ieee 802.11 SpecificationsIntroduction AP-700 User Guide Management and Monitoring Capabilities Command Line InterfaceHTTP/HTTPS Interface SSH Secure Shell Management Snmp ManagementSNMPv3 Secure Management Page AP-700 Hardware Description Installation and InitializationOverview Antennas Installation and Initialization AP-700 User GuideExternal Antennas Active Ethernet LED Indicators Prerequisites Installation and Initialization AP-700 User Guide System Requirements Product Package Required Materials Hardware InstallationCabling the AP-700 Mounting the AP-700 Installing the Security CoverMounting the AP-700 to a Ceiling AP-700 Mounting Plate Mounting the AP-700 to a Wall Installing External Antennas Opening the Antenna Compartment Installing the AP in a Plenum Initialization Using ScanToolScanTool Instructions Scan List Select Tools Internet Options Click LAN SettingsEnter Network Password screen appears Logging 11 System Status Screen Using the Setup Wizard 12 Setup Wizard Setup Wizard Instructions Installing the Software Click Commands Update AP via Http Install Software with Http Interface Install Software with Tftp Server Click Commands Reboot Related Topics Install Updates from your Tftp Server using the CLI System Status Screen System Status Advanced Configuration Configure Main Screen Advanced Configuration AP-700 User Guide Dynamic DNS Support SystemPage Network IP Configuration DNS Client Dhcp ServerAdvanced Start IP Address End IP Address Advanced Configuration AP-700 User Guide NetworkComment optional Dhcp Relay Agent Dhcp Server IP Address Table Dhcp Relay Agent Target IP Address Comment optional Link Integrity Sntp Simple Network Time Protocol Link Integrity Configuration Screen Sntp Configuration Screen Advanced Configuration AP-700 User Guide Network Interfaces Operational Mode Ieee 802.11d Support for Additional Regulatory Domains Advanced Configuration AP-700 User Guide InterfacesSuper Mode and Turbo Mode Configuring 802.11d Support Configuring TX Power Control TX Power Control/Transmit Power Level 10 Wireless Interface Wireless 802.11a/b/g RadioPage Affected Countries Dynamic Frequency Selection/Radar Detection DFS/RD RTS/CTS Medium Reservation Wireless Service Status Channel Blacklist Table Traps Generated During Wireless Service Shutdown and ResumeClick on Configure Interfaces Wireless Set Blacklist Status to Enable Bridging WDS 13 WDS Example 14 WDS Configuration WDS Setup Procedure 15 Adding WDS Links Ethernet 16 Ethernet Sub-tab Management Passwords Services IP Access TableSecure Management Https Access Secure Socket Layer Advanced Configuration AP-700 User Guide ManagementSnmp Settings Http Access 17 Management Services Configuration Screen Configuring SSH SSH Session SetupSSH Clients Uploading Externally Generated Host Keys Click Commands Update AP via Http or via Tftp Radius Based Management Access Serial Configuration Settings Auto Configuration and the CLI Batch File Automatic Configuration AutoConfigSet up Automatic Configuration for Static IP Set up Automatic Configuration for Dynamic IP 19 Automatic Configuration Screen 20 Dhcp Options Setting the Boot Server Host Name Hardware Configuration Reset Chrd Configuring Hardware Configuration Reset Configuration Reset via Serial Port During BootupClick Configure Management Chrd Procedure to Reset Configuration via the Serial Interface Select the Filter Operation Type FilteringEthernet Protocol Static MAC Advanced Configuration AP-700 User Guide Filtering Wireless MAC Address 0020A6124E38 Wired MAC Address 0040F41CDB6AWireless MAC Address 00022D5194E4 Wired MAC Address Click Add under the TCP/UDP Port Filter Table heading AdvancedTCP/UDP Port Number Click Edit under the TCP/UDP Port Filter Table heading Editing TCP/UDP Port Filters Groups Alarms Operational Trap Group Trap Name Description Severity Level Security Trap Group Trap Name Description Severity Level Flash Memory Trap Group Trap Name Description Severity Level Trap Name Description Severity Level Sntp Trap Group Trap Name Description Severity Level Alarm Host TableTftp Trap Group Trap Name Description Severity Level Image Trap Group Trap Name Description Severity Level Advanced Configuration AP-700 User Guide Alarms Syslog Configuring Syslog Event NotificationsEvent Priority Description Syslog Message Name Priority Severity Description Syslog Messages Advanced Configuration AP-700 User Guide 25 Preventing Rogue AP Attacks Rogue Scan Rogue Scan Data Collection Continuous Scanning ModeBackground Scanning Mode Multi-Band Scanning Rogue Scan Click Configure Alarms Rogue Scan 26 Rogue Scan Screen Spanning Tree Bridge Storm Threshold Advanced Configuration AP-700 User Guide Bridge Intra BSS Configuring Interfaces for Packet ForwardingPacket Forwarding Enabling QoS and Adding QoS policies Wireless Multimedia Extensions WME/Quality of Service QoSClick Configure QoS Policy QoS Enter the Priority Mapping Index Advanced Configuration AP-700 User Guide QoS Priority Mapping Click Configure QoS Priority Mapping STA Edca Table and AP Edca Table Enhanced Distributed Channel Access Edca 32 Edca Tables Advanced Configuration AP-700 User Guide QoS Radius Profiles Radius Servers per Authentication Mode and per Vlan Radius Servers Enforcing Vlan Access Control Configuring Radius Profiles Advanced Configuration AP-700 User Guide 35 Add Radius Server Profile 802.1x Authentication using Radius MAC Access Control Via Radius AuthenticationRadius Accounting Accounting Attributes Authentication Attributes101 102 Vlan Overview SSID/VLAN/Security103 104 Management Vlan Typical User Vlan ConfigurationsControl Access to the AP Click Configure SSID/VLAN/Security Mgmt Vlan Disable Vlan Tagging Provide Access to a Wireless Host in the Same WorkgroupSecurity Profile 107 Advanced Configuration AP-700 User Guide SSID/VLAN/SecurityAuthentication Process Wi-Fi Protected Access WPA/802.11i WPA2 108 Authentication Protocol Hierarchy 109 Configuring Security ProfilesClick Configure SSID/VLAN/Security Security Profile VLANs and Security Profiles WPA Station Non Secure StationWEP Station 802.1x Station 111 40 Security Profile Table Add Entries 112 Wireless MAC Access113 114 Configuring an SSID/VLAN with Vlan Tagging Disabled 115 43 SSID/VLAN Edit Entries Screen Vlan Tagging Disabled Click SSID/VLAN/Security Wireless Configuring SSID/VLANs with Vlan Tagging Enabled116 117 45 SSID/VLAN Edit Entries Screen Vlan Tagging Enabled 118 Broadcast Ssid and Closed System 119 Monitoring Monitoring AP-700 User Guide Version Icmp Monitoring Tab IP/ARP Table Learn Table Monitoring Tab Learn Table Radius 124 125 Monitoring AP-700 User Guide Interfaces 126 127 Station Statistics 128 Monitoring AP-700 User Guide Station Statistics Introduction to File Transfer via Tftp or Http Commands129 130 Image Error Checking During File TransferTftp File Transfer Guidelines Http File Transfer Guidelines 131 Update APUpdate AP via Tftp Commands AP-700 User Guide Commands AP-700 User Guide Update AP via Http Update AP via Http132 133 Commands AP-700 User Guide Retrieve FileRetrieve File Retrieve File via Tftp 134 Retrieve File via Http Retrieve File via Http Command Screen Reset RebootCommands AP-700 User Guide Reboot Help Link 13 Help Link Configuration Screen 137 Connectivity Issues TroubleshootingTroubleshooting Concepts Symptoms and Solutions Basic Software Setup and Configuration Problems Client Connection Problems Active Ethernet AE Vlan Operation Issues Reset to Factory Default Procedure Recovery ProceduresForced Reload Procedure 143 Download a New Image Using ScanToolDownload Procedure Preparing to Download the AP Image 144 Download a New Image Using the Bootloader CLI Attaching the Serial Port Cable Setting IP Address using Serial PortInitializing the IP Address using CLI Hardware and Software Requirements 146 Radius Authentication ServerRelated Applications Tftp Server 147 Troubleshooting AP-700 User Guide Related Applications Notation Conventions Command Line Interface CLIGeneral Notes Prerequisite Skills and Knowledge Navigation and Special Keys CLI Error Messages 150 Command Line Interface CLI VariationsBootloader CLI Command Line Interface CLI AP-700 User Guide Operational CLI Commands CLI Command TypesExample 1. Display Command list Example 3. Display parameters for set and show Example 2. Display specific CommandsExample 3a. Display every parameter that can be changed Download Example 3b. Display parameters based on letter sequenceExample 4. Display Prompts for Successive Parameters Done, exit, quit 154 HelpHistory Passwd 155 Parameter Control CommandsShow CLI Command Search Examples Set CLI CommandConfiguring Objects that Require Reboot Set and show Command Examples Example 3 Modify a table entry or row Example 1 Set the Access Point IP Address ParameterExample 4 Enable, Disable, or Delete a table entry or row Example 2 Create a table entry or row Example 6 Show Individual and Table Parameters Example 5 Show the Group Parameters158 159 Using Tables and StringsUsing Strings Working with Tables Log into the AP using Telnet Configuring the AP using CLI commandsSet Basic Configuration Parameters using CLI Commands Log into the AP using HyperTerminal 161 Change PasswordsSet Network Names for the Wireless Interface Set System Name, Location and Contact Information 162 Country Code 163 Configure SSIDs Network Names, VLANs, and Profiles Set up Auto Configuration Other Network SettingsDownload an AP Configuration File from your Tftp Server Backup your AP Configuration File Configure the DNS Client Configure the AP as a Dhcp Server Enable/Disable Closed System Operational ModeAutochannel Select ACS Configure Antenna Diversity Shutdown/Resume Wireless ServiceEnable/Disable Super Mode 802.11a/g only Enable/Disable Turbo Mode 802.11a/g only Configure Management Ports Edit Management IP Access TableSet Communication Ports 169 Configure Secure Socket Layer HttpsSet Telnet Session Timeouts Configure Serial Port Interface Add an Entry to the MAC Access Control Table Create/Enable WDSEnable/Disable WDS Setup MAC Address Access Control Figure A-17 Result of showradiustbl CLI Command 171 Disable Vlan Management Enable Vlan ManagementAdd a Entry to the Wifssid Table CLI Monitoring Parameters 174 Parameter Tables 175 Filtering Parameters 176 Name Type Value Access CLI ParameterSet sysresettodefaults System Parameters 177 DNS Client for Radius Name ResolutionDhcp Server Parameters Name Type Value Access CLI Parameter Network Parameters 178 Dhcp Server table for IP poolsDhcp Relay Group Dhcp Relay Server Table Link Integrity IP Target Table Sntp Parameters Name Type Value Access CLI Parameter179 180 Wireless Interface ParametersInterface Parameters Common Parameters to 802.11a/b/g 181 802.11a Only Parameters 802.11b/g Only Parameters 802.11b Only Parameters182 Mode For 802.11g-only modeFor 802.11b/g mode For 802.11b-only 184 Wireless Distribution System WDS ParametersWireless Interface SSID/VLAN/Profile Parameters Channel Blacklist Parameters 185 Wireless Distribution System WDS Security Table ParametersSnmp Parameters Name Type Value Access CLI Parameter Management Parameters 186 Telnet Parameters Name Type Value Access CLI Parameter Http Parameters Name Type Value Access CLI Parameter187 188 Serial Port Parameters Name Type Value Access CLI ParameterRadius Based Management Access Parameters SSH Parameters Tftp Server Parameters IP Access Table Parameters189 Ethernet Filtering Table Filtering Parameters190 191 Proxy ARP Parameters Name Type Value Access CLI ParameterTCP/UDP Port Filtering TCP/UDP Port Filtering Table Syslog Parameters Alarms ParametersName Type Value Access CLI Parameter Syslog Group 192 Snmp Table Host Table Parameters 193 Syslog Host Table Spanning Tree Priority and Path Cost Table Bridge Parameters194 195 Storm Threshold TableIntra BSS Subscriber Blocking Packet Forwarding Parameters 196 Radius Server Configuration ParametersRadius Parameters General Radius Parameters Security Parameters MAC Access Control Table Security Profile Table VLAN/SSID Parameters198 Other Parameters Iapp Parameters Name Type Value Access CLI ParameterEnabling QoS Name Type Value Access CLI Parameter Configuring QoS Policies 200 Specifying the Mapping between 802.1p and 802.1D Priorities CLI Batch File Defining the QoS Policy used for a Wireless Interface Ssid201 Reboot Behavior Auto Configuration and the CLI Batch FileCLI Batch File Format and Syntax 203 CLI Batch File Error Log Hex Ascii Character ChartCharact Equival Ent 204 Management Functions SpecificationsSoftware Features Number of Stations per BSS Security Functions Medium Access Control MAC FunctionsSpecifications AP-700 User Guide Software Features Advanced Bridging Functions Network Functions Specifications AP-700 User Guide207 Hardware Specifications Upper 149 153 157 161 ISM Band 165 Mode Frequency Channel Product SKU BandAvailable Channels 802.11b/g 802.11a 802.11a RF Performance 802.11a Data Rates Mbps RF Performance210 Online Support Technical SupportSoftware and Documentation Downloads Knowledgebase 211 Technical Support AP-700 User Guide Telephone Support Telephone SupportInternational 212 Limitations of Warranty Statement of WarrantyWarranty Coverage Repair or Replacement Other Adapter Cards Ask a Question or Open an IssueOther Information Search Knowledgebase Product Model Numbers Regulatory Compliance215 Regulatory Compliance AP-700 User Guide Safety Information USA, Canada, & European Union216 217 Federal Communications Commission FCC 218 Modifications 219 Industry Canada IC 220 European Union Country Certification/Reference No Regulatory Compliance Certifications Summary221