Automatic Configuration Screen | Proxim AP-700 instruction

Advanced Configuration

AP-700 User Guide

Management

Figure 4-19 Automatic Configuration Screen

Set up Automatic Configuration for Dynamic IP

Perform the following procedure to enable and set up Automatic Configuration when you have a dynamic IP address for the TFTP server via DHCP.

The Configuration filename and the TFTP server IP address are contained in the DHCP response when the AP gets its IP address dynamically from the DHCP server. A Syslog server address is also contained in the DHCP response, allowing the AP to send Auto Configuration success and failure messages to a Syslog server.

NOTE: The configuration filename and TFTP server IP address are configured only when the AP is configured for Static IP. If the AP is configured for Dynamic IP these parameters are not used and obtained from DHCP.

1.Click Configure > Management > AutoConfig. The Automatic Configuration Screen appears.

2.Check Enable Auto Configuration.

When the AP is Configured with Dynamic IP, the DHCP server should be configured with the TFTP Server IP address ("Boot Server Host Name", option 66) and Configuration file ("Bootfile name", option 67) as follows (note that this example uses a Windows 2000 server):

3.Select DHCP Server > DHCP Option > Scope. The DHCP Options: Scope Screen appears.

66

Image 66

Proxim AP-700 manual Automatic Configuration Screen, Set up Automatic Configuration for Dynamic IP

Contents

ORiNOCO AP-700 Access Point User Guide OpenSSL License Note CopyrightTrademarks AP-700 User Guide Contents Contents AP-700 User Guide Management Commands TroubleshootingMonitoring Command Line Interface CLI General Notes Technical Support Ascii Character Chart C SpecificationsStatement of Warranty Regulatory Compliance AP-700 User Guide Introduction to Wireless Networking IntroductionDocument Conventions Ieee 802.11 Specifications Guidelines for RoamingIntroduction AP-700 User Guide Command Line Interface Management and Monitoring CapabilitiesHTTP/HTTPS Interface Snmp Management SSH Secure Shell ManagementSNMPv3 Secure Management Page Installation and Initialization AP-700 Hardware DescriptionOverview Installation and Initialization AP-700 User Guide AntennasExternal Antennas LED Indicators Active Ethernet Prerequisites Installation and Initialization AP-700 User Guide Product Package System Requirements Hardware Installation Required MaterialsCabling the AP-700 Installing the Security Cover Mounting the AP-700Mounting the AP-700 to a Ceiling Installing External Antennas AP-700 Mounting Plate Mounting the AP-700 to a Wall Installing the AP in a Plenum Opening the Antenna Compartment Using ScanTool InitializationScanTool Instructions Scan List Logging Click LAN SettingsEnter Network Password screen appears Select Tools Internet Options Using the Setup Wizard 11 System Status Screen 12 Setup Wizard Setup Wizard Instructions Installing the Software Install Software with Http Interface Click Commands Update AP via Http Click Commands Reboot Install Software with Tftp Server Install Updates from your Tftp Server using the CLI Related Topics System Status System Status Screen Advanced Configuration Advanced Configuration AP-700 User Guide Configure Main Screen System Dynamic DNS SupportPage IP Configuration Network Dhcp Server DNS ClientAdvanced Advanced Configuration AP-700 User Guide Network Start IP Address End IP AddressComment optional Dhcp Relay Agent Dhcp Relay Agent Dhcp Server IP Address Table Link Integrity Target IP Address Comment optional Link Integrity Configuration Screen Sntp Simple Network Time Protocol Sntp Configuration Screen Advanced Configuration AP-700 User Guide Network Operational Mode Interfaces Configuring 802.11d Support Advanced Configuration AP-700 User Guide InterfacesSuper Mode and Turbo Mode Ieee 802.11d Support for Additional Regulatory Domains TX Power Control/Transmit Power Level Configuring TX Power Control Wireless 802.11a/b/g Radio 10 Wireless InterfacePage Dynamic Frequency Selection/Radar Detection DFS/RD Affected Countries Wireless Service Status RTS/CTS Medium Reservation Set Blacklist Status to Enable Traps Generated During Wireless Service Shutdown and ResumeClick on Configure Interfaces Wireless Channel Blacklist Table 13 WDS Example Bridging WDS WDS Setup Procedure 14 WDS Configuration Ethernet 15 Adding WDS Links 16 Ethernet Sub-tab Passwords Management IP Access Table ServicesSecure Management Http Access Advanced Configuration AP-700 User Guide ManagementSnmp Settings Https Access Secure Socket Layer 17 Management Services Configuration Screen SSH Session Setup Configuring SSHSSH Clients Click Commands Update AP via Http or via Tftp Uploading Externally Generated Host Keys Serial Configuration Settings Radius Based Management Access Automatic Configuration AutoConfig Auto Configuration and the CLI Batch FileSet up Automatic Configuration for Static IP 19 Automatic Configuration Screen Set up Automatic Configuration for Dynamic IP Hardware Configuration Reset Chrd 20 Dhcp Options Setting the Boot Server Host Name Configuration Reset via Serial Port During Bootup Configuring Hardware Configuration ResetClick Configure Management Chrd Procedure to Reset Configuration via the Serial Interface Static MAC FilteringEthernet Protocol Select the Filter Operation Type Advanced Configuration AP-700 User Guide Filtering Wired MAC Address Wired MAC Address 0040F41CDB6AWireless MAC Address 00022D5194E4 Wireless MAC Address 0020A6124E38 Number AdvancedTCP/UDP Port Click Add under the TCP/UDP Port Filter Table heading Editing TCP/UDP Port Filters Click Edit under the TCP/UDP Port Filter Table heading Alarms Groups Security Trap Group Trap Name Description Severity Level Operational Trap Group Trap Name Description Severity Level Trap Name Description Severity Level Flash Memory Trap Group Trap Name Description Severity Level Image Trap Group Trap Name Description Severity Level Alarm Host TableTftp Trap Group Trap Name Description Severity Level Sntp Trap Group Trap Name Description Severity Level Advanced Configuration AP-700 User Guide Alarms Configuring Syslog Event Notifications SyslogEvent Priority Description Syslog Messages Syslog Message Name Priority Severity Description Advanced Configuration AP-700 User Guide Rogue Scan 25 Preventing Rogue AP Attacks Multi-Band Scanning Continuous Scanning ModeBackground Scanning Mode Rogue Scan Data Collection Click Configure Alarms Rogue Scan Rogue Scan 26 Rogue Scan Screen Bridge Spanning Tree Advanced Configuration AP-700 User Guide Bridge Storm Threshold Configuring Interfaces for Packet Forwarding Intra BSSPacket Forwarding QoS Wireless Multimedia Extensions WME/Quality of Service QoSClick Configure QoS Policy Enabling QoS and Adding QoS policies Advanced Configuration AP-700 User Guide QoS Enter the Priority Mapping Index Click Configure QoS Priority Mapping Priority Mapping Enhanced Distributed Channel Access Edca STA Edca Table and AP Edca Table 32 Edca Tables Advanced Configuration AP-700 User Guide QoS Radius Servers per Authentication Mode and per Vlan Radius Profiles Configuring Radius Profiles Radius Servers Enforcing Vlan Access Control Advanced Configuration AP-700 User Guide 35 Add Radius Server Profile MAC Access Control Via Radius Authentication 802.1x Authentication using RadiusRadius Accounting Authentication Attributes Accounting Attributes101 102 SSID/VLAN/Security Vlan Overview103 104 Click Configure SSID/VLAN/Security Mgmt Vlan Typical User Vlan ConfigurationsControl Access to the AP Management Vlan Provide Access to a Wireless Host in the Same Workgroup Disable Vlan TaggingSecurity Profile Wi-Fi Protected Access WPA/802.11i WPA2 Advanced Configuration AP-700 User Guide SSID/VLAN/SecurityAuthentication Process 107 Authentication Protocol Hierarchy 108 VLANs and Security Profiles Configuring Security ProfilesClick Configure SSID/VLAN/Security Security Profile 109 802.1x Station Non Secure StationWEP Station WPA Station 111 40 Security Profile Table Add Entries 112 MAC Access Wireless113 Configuring an SSID/VLAN with Vlan Tagging Disabled 114 43 SSID/VLAN Edit Entries Screen Vlan Tagging Disabled 115 Configuring SSID/VLANs with Vlan Tagging Enabled Click SSID/VLAN/Security Wireless116 45 SSID/VLAN Edit Entries Screen Vlan Tagging Enabled 117 Broadcast Ssid and Closed System 118 Monitoring 119 Version Monitoring AP-700 User Guide IP/ARP Table Icmp Monitoring Tab Learn Table Learn Table Monitoring Tab Radius 124 Monitoring AP-700 User Guide Interfaces 125 126 Station Statistics 127 Monitoring AP-700 User Guide Station Statistics 128 Commands Introduction to File Transfer via Tftp or Http129 Http File Transfer Guidelines Image Error Checking During File TransferTftp File Transfer Guidelines 130 Commands AP-700 User Guide Update APUpdate AP via Tftp 131 Update AP via Http Commands AP-700 User Guide Update AP via Http132 Retrieve File via Tftp Commands AP-700 User Guide Retrieve FileRetrieve File 133 Retrieve File via Http 134 Retrieve File via Http Command Screen Reboot ResetCommands AP-700 User Guide Reboot 13 Help Link Configuration Screen 137 Help Link Symptoms and Solutions TroubleshootingTroubleshooting Concepts Connectivity Issues Basic Software Setup and Configuration Problems Client Connection Problems Vlan Operation Issues Active Ethernet AE Recovery Procedures Reset to Factory Default ProcedureForced Reload Procedure Preparing to Download the AP Image Download a New Image Using ScanToolDownload Procedure 143 Download a New Image Using the Bootloader CLI 144 Hardware and Software Requirements Setting IP Address using Serial PortInitializing the IP Address using CLI Attaching the Serial Port Cable Tftp Server Radius Authentication ServerRelated Applications 146 Troubleshooting AP-700 User Guide Related Applications 147 Prerequisite Skills and Knowledge Command Line Interface CLIGeneral Notes Notation Conventions CLI Error Messages Navigation and Special Keys Command Line Interface CLI AP-700 User Guide Command Line Interface CLI VariationsBootloader CLI 150 CLI Command Types Operational CLI CommandsExample 1. Display Command list Example 2. Display specific Commands Example 3. Display parameters for set and showExample 3a. Display every parameter that can be changed Done, exit, quit Example 3b. Display parameters based on letter sequenceExample 4. Display Prompts for Successive Parameters Download Passwd HelpHistory 154 Search Parameter Control CommandsShow CLI Command 155 Set and show Command Examples Set CLI CommandConfiguring Objects that Require Reboot Examples Example 2 Create a table entry or row Example 1 Set the Access Point IP Address ParameterExample 4 Enable, Disable, or Delete a table entry or row Example 3 Modify a table entry or row Example 5 Show the Group Parameters Example 6 Show Individual and Table Parameters158 Working with Tables Using Tables and StringsUsing Strings 159 Log into the AP using HyperTerminal Configuring the AP using CLI commandsSet Basic Configuration Parameters using CLI Commands Log into the AP using Telnet Set System Name, Location and Contact Information Change PasswordsSet Network Names for the Wireless Interface 161 Country Code 162 Configure SSIDs Network Names, VLANs, and Profiles 163 Backup your AP Configuration File Other Network SettingsDownload an AP Configuration File from your Tftp Server Set up Auto Configuration Configure the AP as a Dhcp Server Configure the DNS Client Operational Mode Enable/Disable Closed SystemAutochannel Select ACS Enable/Disable Turbo Mode 802.11a/g only Shutdown/Resume Wireless ServiceEnable/Disable Super Mode 802.11a/g only Configure Antenna Diversity Edit Management IP Access Table Configure Management PortsSet Communication Ports Configure Serial Port Interface Configure Secure Socket Layer HttpsSet Telnet Session Timeouts 169 Setup MAC Address Access Control Create/Enable WDSEnable/Disable WDS Add an Entry to the MAC Access Control Table Figure A-17 Result of showradiustbl CLI Command 171 Enable Vlan Management Disable Vlan ManagementAdd a Entry to the Wifssid Table CLI Monitoring Parameters Parameter Tables 174 Filtering Parameters 175 System Parameters Name Type Value Access CLI ParameterSet sysresettodefaults 176 Network Parameters DNS Client for Radius Name ResolutionDhcp Server Parameters Name Type Value Access CLI Parameter 177 Dhcp Relay Server Table Dhcp Server table for IP poolsDhcp Relay Group 178 Sntp Parameters Name Type Value Access CLI Parameter Link Integrity IP Target Table179 Common Parameters to 802.11a/b/g Wireless Interface ParametersInterface Parameters 180 802.11a Only Parameters 181 802.11b Only Parameters 802.11b/g Only Parameters182 For 802.11b-only For 802.11g-only modeFor 802.11b/g mode Mode Channel Blacklist Parameters Wireless Distribution System WDS ParametersWireless Interface SSID/VLAN/Profile Parameters 184 Management Parameters Wireless Distribution System WDS Security Table ParametersSnmp Parameters Name Type Value Access CLI Parameter 185 186 Http Parameters Name Type Value Access CLI Parameter Telnet Parameters Name Type Value Access CLI Parameter187 SSH Parameters Serial Port Parameters Name Type Value Access CLI ParameterRadius Based Management Access Parameters 188 IP Access Table Parameters Tftp Server Parameters189 Filtering Parameters Ethernet Filtering Table190 TCP/UDP Port Filtering Table Proxy ARP Parameters Name Type Value Access CLI ParameterTCP/UDP Port Filtering 191 Snmp Table Host Table Parameters Alarms ParametersName Type Value Access CLI Parameter Syslog Group 192 Syslog Parameters Syslog Host Table 193 Bridge Parameters Spanning Tree Priority and Path Cost Table194 Packet Forwarding Parameters Storm Threshold TableIntra BSS Subscriber Blocking 195 General Radius Parameters Radius Server Configuration ParametersRadius Parameters 196 MAC Access Control Table Security Parameters VLAN/SSID Parameters Security Profile Table198 Configuring QoS Policies Iapp Parameters Name Type Value Access CLI ParameterEnabling QoS Name Type Value Access CLI Parameter Other Parameters Specifying the Mapping between 802.1p and 802.1D Priorities 200 Defining the QoS Policy used for a Wireless Interface Ssid CLI Batch File201 Auto Configuration and the CLI Batch File Reboot BehaviorCLI Batch File Format and Syntax CLI Batch File Error Log 203 Ascii Character Chart HexCharact Equival Ent 204 Number of Stations per BSS SpecificationsSoftware Features Management Functions Advanced Bridging Functions Medium Access Control MAC FunctionsSpecifications AP-700 User Guide Software Features Security Functions Specifications AP-700 User Guide Network Functions207 Hardware Specifications 802.11b/g 802.11a Mode Frequency Channel Product SKU BandAvailable Channels Upper 149 153 157 161 ISM Band 165 RF Performance 802.11a RF Performance 802.11a Data Rates Mbps210 Technical Support Online SupportSoftware and Documentation Downloads Knowledgebase 211 Telephone Support Technical Support AP-700 User Guide Telephone SupportInternational 212 Repair or Replacement Statement of WarrantyWarranty Coverage Limitations of Warranty Search Knowledgebase Ask a Question or Open an IssueOther Information Other Adapter Cards Regulatory Compliance Product Model Numbers215 Safety Information USA, Canada, & European Union Regulatory Compliance AP-700 User Guide216 Federal Communications Commission FCC 217 Modifications 218 Industry Canada IC 219 European Union 220 Regulatory Compliance Certifications Summary Country Certification/Reference No221