CLI Monitoring Parameters | Proxim AP-700 specs

Command Line Interface (CLI)

AP-700 User Guide

CLI Monitoring Parameters

Set Security Profile Parameters

Configure a Security Profile with Non Secure Security Mode

[Device-Name]>set secprofiletbl <index> secmode nonsecure status enable

Example:

[Device-Name]>set secprofiletbl 2 secmode nonsecure status enable

Configure a Security Profile with WEP Security Mode

[Device-Name]>set secprofiletbl <index> secmode wep encryptkey0 <value> encryptkeylength <vakue> encryptkeytx <value> status enable

Example:

[Device-Name]>set secprofiletbl 3 secmode wep encryptkey0 12345 encryptkeylength 1 encryptkeytx 0 status enable

Configure a Security Profile with 802.1x Security Mode

[Device-Name]>set secprofiletbl <index> secmode 802.1x rekeyint 900 status enable

Example:

[Device-Name]>set secprofiletbl 4 secmode 802.1x rekeyint 900 status enable

Configure a Security Profile with WPA Security Mode

[Device-Name]>set secprofiletbl <index> secmode wpa rekeyint 900 status enable

Example:

[Device-Name]>set secprofiletbl 5 secmode wpa rekeyint 900 status enable

Configure a Security Profile with WPA-PSK Security Mode

[Device-Name]>set secprofiletbl <index> secmode wpa-psk passphrase <value> status enable

Example:

[Device-Name]>set secprofiletbl 6 secmode wpa-psk passphrase 12345678 status enable

Configure a Security Profile with 802.11i Security Mode

[Device-Name]>set secprofiletbl <index> secmode 802.11i rekeyint <value> status enable

Example:

[Device-Name]>set secprofiletbl 7 secmode 802.11i rekeyint 900 status enable

Configure a Security Profile with 802.11i-PSK Security Mode

[Device-Name]>set secprofiletbl <index> secmode 802.11i-psk passphrase <value> status enable

Example:

[Device-Name]>set secprofiletbl 8 secmode 802.11i-psk passphrase 12345678 status enable

CLI Monitoring Parameters

Using the show command with the following table parameters will display operating statistics for the AP (these are the same statistics that are described in the Monitoring section).

•staticmp: Displays the ICMP statistics.

•statarptbl: Displays the IP ARP Table statistics.

•statbridgetbl: Displays the Learn Table.

173

Image 173

Proxim AP-700 manual CLI Monitoring Parameters

Contents

ORiNOCO AP-700 Access Point User Guide Trademarks CopyrightOpenSSL License Note AP-700 User Guide Contents Management Contents AP-700 User Guide Monitoring CommandsTroubleshooting General Notes Command Line Interface CLI Statement of Warranty Ascii Character Chart C SpecificationsTechnical Support Regulatory Compliance AP-700 User Guide Document Conventions Introduction to Wireless NetworkingIntroduction Introduction AP-700 User Guide Ieee 802.11 SpecificationsGuidelines for Roaming HTTP/HTTPS Interface Command Line InterfaceManagement and Monitoring Capabilities SNMPv3 Secure Management Snmp ManagementSSH Secure Shell Management Page Overview Installation and InitializationAP-700 Hardware Description External Antennas Installation and Initialization AP-700 User GuideAntennas Active Ethernet LED Indicators Prerequisites Installation and Initialization AP-700 User Guide System Requirements Product Package Cabling the AP-700 Hardware InstallationRequired Materials Mounting the AP-700 to a Ceiling Installing the Security CoverMounting the AP-700 AP-700 Mounting Plate Mounting the AP-700 to a Wall Installing External Antennas Opening the Antenna Compartment Installing the AP in a Plenum ScanTool Instructions Using ScanToolInitialization Scan List Enter Network Password screen appears Click LAN SettingsLogging Select Tools Internet Options 11 System Status Screen Using the Setup Wizard 12 Setup Wizard Setup Wizard Instructions Installing the Software Click Commands Update AP via Http Install Software with Http Interface Install Software with Tftp Server Click Commands Reboot Related Topics Install Updates from your Tftp Server using the CLI System Status Screen System Status Advanced Configuration Configure Main Screen Advanced Configuration AP-700 User Guide Dynamic DNS Support SystemPage Network IP Configuration Advanced Dhcp ServerDNS Client Comment optional Advanced Configuration AP-700 User Guide NetworkStart IP Address End IP Address Dhcp Relay Agent Dhcp Server IP Address Table Dhcp Relay Agent Target IP Address Comment optional Link Integrity Sntp Simple Network Time Protocol Link Integrity Configuration Screen Sntp Configuration Screen Advanced Configuration AP-700 User Guide Network Interfaces Operational Mode Super Mode and Turbo Mode Advanced Configuration AP-700 User Guide InterfacesConfiguring 802.11d Support Ieee 802.11d Support for Additional Regulatory Domains Configuring TX Power Control TX Power Control/Transmit Power Level 10 Wireless Interface Wireless 802.11a/b/g RadioPage Affected Countries Dynamic Frequency Selection/Radar Detection DFS/RD RTS/CTS Medium Reservation Wireless Service Status Click on Configure Interfaces Wireless Traps Generated During Wireless Service Shutdown and ResumeSet Blacklist Status to Enable Channel Blacklist Table Bridging WDS 13 WDS Example 14 WDS Configuration WDS Setup Procedure 15 Adding WDS Links Ethernet 16 Ethernet Sub-tab Management Passwords Secure Management IP Access TableServices Snmp Settings Advanced Configuration AP-700 User Guide ManagementHttp Access Https Access Secure Socket Layer 17 Management Services Configuration Screen SSH Clients SSH Session SetupConfiguring SSH Uploading Externally Generated Host Keys Click Commands Update AP via Http or via Tftp Radius Based Management Access Serial Configuration Settings Set up Automatic Configuration for Static IP Automatic Configuration AutoConfigAuto Configuration and the CLI Batch File Set up Automatic Configuration for Dynamic IP 19 Automatic Configuration Screen 20 Dhcp Options Setting the Boot Server Host Name Hardware Configuration Reset Chrd Click Configure Management Chrd Configuration Reset via Serial Port During BootupConfiguring Hardware Configuration Reset Procedure to Reset Configuration via the Serial Interface Ethernet Protocol FilteringStatic MAC Select the Filter Operation Type Advanced Configuration AP-700 User Guide Filtering Wireless MAC Address 00022D5194E4 Wired MAC Address 0040F41CDB6AWired MAC Address Wireless MAC Address 0020A6124E38 TCP/UDP Port AdvancedNumber Click Add under the TCP/UDP Port Filter Table heading Click Edit under the TCP/UDP Port Filter Table heading Editing TCP/UDP Port Filters Groups Alarms Operational Trap Group Trap Name Description Severity Level Security Trap Group Trap Name Description Severity Level Flash Memory Trap Group Trap Name Description Severity Level Trap Name Description Severity Level Tftp Trap Group Trap Name Description Severity Level Alarm Host TableImage Trap Group Trap Name Description Severity Level Sntp Trap Group Trap Name Description Severity Level Advanced Configuration AP-700 User Guide Alarms Event Priority Description Configuring Syslog Event NotificationsSyslog Syslog Message Name Priority Severity Description Syslog Messages Advanced Configuration AP-700 User Guide 25 Preventing Rogue AP Attacks Rogue Scan Background Scanning Mode Continuous Scanning ModeMulti-Band Scanning Rogue Scan Data Collection Rogue Scan Click Configure Alarms Rogue Scan 26 Rogue Scan Screen Spanning Tree Bridge Storm Threshold Advanced Configuration AP-700 User Guide Bridge Packet Forwarding Configuring Interfaces for Packet ForwardingIntra BSS Click Configure QoS Policy Wireless Multimedia Extensions WME/Quality of Service QoSQoS Enabling QoS and Adding QoS policies Enter the Priority Mapping Index Advanced Configuration AP-700 User Guide QoS Priority Mapping Click Configure QoS Priority Mapping STA Edca Table and AP Edca Table Enhanced Distributed Channel Access Edca 32 Edca Tables Advanced Configuration AP-700 User Guide QoS Radius Profiles Radius Servers per Authentication Mode and per Vlan Radius Servers Enforcing Vlan Access Control Configuring Radius Profiles Advanced Configuration AP-700 User Guide 35 Add Radius Server Profile Radius Accounting MAC Access Control Via Radius Authentication802.1x Authentication using Radius 101 Authentication AttributesAccounting Attributes 102 103 SSID/VLAN/SecurityVlan Overview 104 Control Access to the AP Typical User Vlan ConfigurationsClick Configure SSID/VLAN/Security Mgmt Vlan Management Vlan Security Profile Provide Access to a Wireless Host in the Same WorkgroupDisable Vlan Tagging Authentication Process Advanced Configuration AP-700 User Guide SSID/VLAN/SecurityWi-Fi Protected Access WPA/802.11i WPA2 107 108 Authentication Protocol Hierarchy Click Configure SSID/VLAN/Security Security Profile Configuring Security ProfilesVLANs and Security Profiles 109 WEP Station Non Secure Station802.1x Station WPA Station 111 40 Security Profile Table Add Entries 112 113 MAC AccessWireless 114 Configuring an SSID/VLAN with Vlan Tagging Disabled 115 43 SSID/VLAN Edit Entries Screen Vlan Tagging Disabled 116 Configuring SSID/VLANs with Vlan Tagging EnabledClick SSID/VLAN/Security Wireless 117 45 SSID/VLAN Edit Entries Screen Vlan Tagging Enabled 118 Broadcast Ssid and Closed System 119 Monitoring Monitoring AP-700 User Guide Version Icmp Monitoring Tab IP/ARP Table Learn Table Monitoring Tab Learn Table Radius 124 125 Monitoring AP-700 User Guide Interfaces 126 127 Station Statistics 128 Monitoring AP-700 User Guide Station Statistics 129 CommandsIntroduction to File Transfer via Tftp or Http Tftp File Transfer Guidelines Image Error Checking During File TransferHttp File Transfer Guidelines 130 Update AP via Tftp Update APCommands AP-700 User Guide 131 132 Update AP via HttpCommands AP-700 User Guide Update AP via Http Retrieve File Commands AP-700 User Guide Retrieve FileRetrieve File via Tftp 133 134 Retrieve File via Http Retrieve File via Http Command Screen Commands AP-700 User Guide Reboot RebootReset Help Link 13 Help Link Configuration Screen 137 Troubleshooting Concepts TroubleshootingSymptoms and Solutions Connectivity Issues Basic Software Setup and Configuration Problems Client Connection Problems Active Ethernet AE Vlan Operation Issues Forced Reload Procedure Recovery ProceduresReset to Factory Default Procedure Download Procedure Download a New Image Using ScanToolPreparing to Download the AP Image 143 144 Download a New Image Using the Bootloader CLI Initializing the IP Address using CLI Setting IP Address using Serial PortHardware and Software Requirements Attaching the Serial Port Cable Related Applications Radius Authentication ServerTftp Server 146 147 Troubleshooting AP-700 User Guide Related Applications General Notes Command Line Interface CLIPrerequisite Skills and Knowledge Notation Conventions Navigation and Special Keys CLI Error Messages Bootloader CLI Command Line Interface CLI VariationsCommand Line Interface CLI AP-700 User Guide 150 Example 1. Display Command list CLI Command TypesOperational CLI Commands Example 3a. Display every parameter that can be changed Example 2. Display specific CommandsExample 3. Display parameters for set and show Example 4. Display Prompts for Successive Parameters Example 3b. Display parameters based on letter sequenceDone, exit, quit Download History HelpPasswd 154 Show CLI Command Parameter Control CommandsSearch 155 Configuring Objects that Require Reboot Set CLI CommandSet and show Command Examples Examples Example 4 Enable, Disable, or Delete a table entry or row Example 1 Set the Access Point IP Address ParameterExample 2 Create a table entry or row Example 3 Modify a table entry or row 158 Example 5 Show the Group ParametersExample 6 Show Individual and Table Parameters Using Strings Using Tables and StringsWorking with Tables 159 Set Basic Configuration Parameters using CLI Commands Configuring the AP using CLI commandsLog into the AP using HyperTerminal Log into the AP using Telnet Set Network Names for the Wireless Interface Change PasswordsSet System Name, Location and Contact Information 161 162 Country Code 163 Configure SSIDs Network Names, VLANs, and Profiles Download an AP Configuration File from your Tftp Server Other Network SettingsBackup your AP Configuration File Set up Auto Configuration Configure the DNS Client Configure the AP as a Dhcp Server Autochannel Select ACS Operational ModeEnable/Disable Closed System Enable/Disable Super Mode 802.11a/g only Shutdown/Resume Wireless ServiceEnable/Disable Turbo Mode 802.11a/g only Configure Antenna Diversity Set Communication Ports Edit Management IP Access TableConfigure Management Ports Set Telnet Session Timeouts Configure Secure Socket Layer HttpsConfigure Serial Port Interface 169 Enable/Disable WDS Create/Enable WDSSetup MAC Address Access Control Add an Entry to the MAC Access Control Table Figure A-17 Result of showradiustbl CLI Command 171 Add a Entry to the Wifssid Table Enable Vlan ManagementDisable Vlan Management CLI Monitoring Parameters 174 Parameter Tables 175 Filtering Parameters Set sysresettodefaults Name Type Value Access CLI ParameterSystem Parameters 176 Dhcp Server Parameters Name Type Value Access CLI Parameter DNS Client for Radius Name ResolutionNetwork Parameters 177 Dhcp Relay Group Dhcp Server table for IP poolsDhcp Relay Server Table 178 179 Sntp Parameters Name Type Value Access CLI ParameterLink Integrity IP Target Table Interface Parameters Wireless Interface ParametersCommon Parameters to 802.11a/b/g 180 181 802.11a Only Parameters 182 802.11b Only Parameters802.11b/g Only Parameters For 802.11b/g mode For 802.11g-only modeFor 802.11b-only Mode Wireless Interface SSID/VLAN/Profile Parameters Wireless Distribution System WDS ParametersChannel Blacklist Parameters 184 Snmp Parameters Name Type Value Access CLI Parameter Wireless Distribution System WDS Security Table ParametersManagement Parameters 185 186 187 Http Parameters Name Type Value Access CLI ParameterTelnet Parameters Name Type Value Access CLI Parameter Radius Based Management Access Parameters Serial Port Parameters Name Type Value Access CLI ParameterSSH Parameters 188 189 IP Access Table ParametersTftp Server Parameters 190 Filtering ParametersEthernet Filtering Table TCP/UDP Port Filtering Proxy ARP Parameters Name Type Value Access CLI ParameterTCP/UDP Port Filtering Table 191 Name Type Value Access CLI Parameter Syslog Group 192 Alarms ParametersSnmp Table Host Table Parameters Syslog Parameters 193 Syslog Host Table 194 Bridge ParametersSpanning Tree Priority and Path Cost Table Intra BSS Subscriber Blocking Storm Threshold TablePacket Forwarding Parameters 195 Radius Parameters Radius Server Configuration ParametersGeneral Radius Parameters 196 Security Parameters MAC Access Control Table 198 VLAN/SSID ParametersSecurity Profile Table Enabling QoS Name Type Value Access CLI Parameter Iapp Parameters Name Type Value Access CLI ParameterConfiguring QoS Policies Other Parameters 200 Specifying the Mapping between 802.1p and 802.1D Priorities 201 Defining the QoS Policy used for a Wireless Interface SsidCLI Batch File CLI Batch File Format and Syntax Auto Configuration and the CLI Batch FileReboot Behavior 203 CLI Batch File Error Log Charact Equival Ent 204 Ascii Character ChartHex Software Features SpecificationsNumber of Stations per BSS Management Functions Specifications AP-700 User Guide Software Features Medium Access Control MAC FunctionsAdvanced Bridging Functions Security Functions 207 Specifications AP-700 User GuideNetwork Functions Hardware Specifications Available Channels Mode Frequency Channel Product SKU Band802.11b/g 802.11a Upper 149 153 157 161 ISM Band 165 210 RF Performance802.11a RF Performance 802.11a Data Rates Mbps Software and Documentation Downloads Knowledgebase 211 Technical SupportOnline Support International 212 Telephone SupportTechnical Support AP-700 User Guide Telephone Support Warranty Coverage Statement of WarrantyRepair or Replacement Limitations of Warranty Other Information Ask a Question or Open an IssueSearch Knowledgebase Other Adapter Cards 215 Regulatory ComplianceProduct Model Numbers 216 Safety Information USA, Canada, & European UnionRegulatory Compliance AP-700 User Guide 217 Federal Communications Commission FCC 218 Modifications 219 Industry Canada IC 220 European Union 221 Regulatory Compliance Certifications SummaryCountry Certification/Reference No