Manuals / Proxim / Computer Equipment / Network Router

Proxim manual Storm Threshold, Advanced Configuration AP-700 User Guide Bridge

Models: AP-700

1 221

Download 221 pages 11.69 Kb

Page 88

Advanced Configuration	AP-700 User Guide
Bridge

Figure 4-27 Spanning Tree Sub-Tab

Storm Threshold

Storm Threshold is an advanced Bridge setup option that you can use to protect the network against data overload by:

•Specifying a maximum number of frames per second as received from a single network device (identified by its MAC address).

•Specifying an absolute maximum number of messages per interface.

The Storm Threshold parameters allow you to specify a set of thresholds for each interface of the AP, identifying separate values for the number of broadcast messages/second and Multicast messages/second.

When the number of frames for an interface or from a single network device exceeds the maximum value per second, the AP will ignore all subsequent messages in that second received on that interface or from that network device.

•Address Threshold: Enter the maximum allowed number of packets per second.

•Ethernet Threshold: Enter the maximum allowed number of packets per second.

88

Image 88

Proxim manual Storm Threshold, Advanced Configuration AP-700 User Guide Bridge

Contents

ORiNOCO AP-700 Access Point User Guide Copyright TrademarksOpenSSL License Note AP-700 User GuideContents Contents AP-700 User Guide ManagementTroubleshooting CommandsMonitoring Command Line Interface CLI General NotesAscii Character Chart C Specifications Statement of WarrantyTechnical Support Regulatory ComplianceAP-700 User Guide Introduction Introduction to Wireless NetworkingDocument Conventions Guidelines for Roaming Ieee 802.11 SpecificationsIntroduction AP-700 User Guide Management and Monitoring Capabilities Command Line InterfaceHTTP/HTTPS Interface SSH Secure Shell Management Snmp ManagementSNMPv3 Secure Management Page AP-700 Hardware Description Installation and InitializationOverview Antennas Installation and Initialization AP-700 User GuideExternal Antennas LED Indicators Active EthernetPrerequisites Installation and Initialization AP-700 User Guide Product Package System RequirementsRequired Materials Hardware InstallationCabling the AP-700 Mounting the AP-700 Installing the Security CoverMounting the AP-700 to a Ceiling Installing External Antennas AP-700 Mounting Plate Mounting the AP-700 to a WallInstalling the AP in a Plenum Opening the Antenna CompartmentInitialization Using ScanToolScanTool Instructions Scan List Click LAN Settings Enter Network Password screen appearsLogging Select Tools Internet OptionsUsing the Setup Wizard 11 System Status Screen12 Setup Wizard Setup Wizard Instructions Installing the Software Install Software with Http Interface Click Commands Update AP via HttpClick Commands Reboot Install Software with Tftp ServerInstall Updates from your Tftp Server using the CLI Related TopicsSystem Status System Status ScreenAdvanced Configuration Advanced Configuration AP-700 User Guide Configure Main ScreenSystem Dynamic DNS SupportPage IP Configuration NetworkDNS Client Dhcp ServerAdvanced Start IP Address End IP Address Advanced Configuration AP-700 User Guide NetworkComment optional Dhcp Relay Agent Dhcp Relay Agent Dhcp Server IP Address TableLink Integrity Target IP Address Comment optionalLink Integrity Configuration Screen Sntp Simple Network Time ProtocolSntp Configuration Screen Advanced Configuration AP-700 User Guide Network Operational Mode InterfacesAdvanced Configuration AP-700 User Guide Interfaces Super Mode and Turbo ModeConfiguring 802.11d Support Ieee 802.11d Support for Additional Regulatory DomainsTX Power Control/Transmit Power Level Configuring TX Power ControlWireless 802.11a/b/g Radio 10 Wireless InterfacePage Dynamic Frequency Selection/Radar Detection DFS/RD Affected CountriesWireless Service Status RTS/CTS Medium ReservationTraps Generated During Wireless Service Shutdown and Resume Click on Configure Interfaces WirelessSet Blacklist Status to Enable Channel Blacklist Table13 WDS Example Bridging WDSWDS Setup Procedure 14 WDS ConfigurationEthernet 15 Adding WDS Links16 Ethernet Sub-tab Passwords ManagementServices IP Access TableSecure Management Advanced Configuration AP-700 User Guide Management Snmp SettingsHttp Access Https Access Secure Socket Layer17 Management Services Configuration Screen Configuring SSH SSH Session SetupSSH Clients Click Commands Update AP via Http or via Tftp Uploading Externally Generated Host KeysSerial Configuration Settings Radius Based Management AccessAuto Configuration and the CLI Batch File Automatic Configuration AutoConfigSet up Automatic Configuration for Static IP 19 Automatic Configuration Screen Set up Automatic Configuration for Dynamic IPHardware Configuration Reset Chrd 20 Dhcp Options Setting the Boot Server Host NameConfiguring Hardware Configuration Reset Configuration Reset via Serial Port During BootupClick Configure Management Chrd Procedure to Reset Configuration via the Serial Interface Filtering Ethernet ProtocolStatic MAC Select the Filter Operation TypeAdvanced Configuration AP-700 User Guide Filtering Wired MAC Address 0040F41CDB6A Wireless MAC Address 00022D5194E4Wired MAC Address Wireless MAC Address 0020A6124E38Advanced TCP/UDP PortNumber Click Add under the TCP/UDP Port Filter Table headingEditing TCP/UDP Port Filters Click Edit under the TCP/UDP Port Filter Table headingAlarms GroupsSecurity Trap Group Trap Name Description Severity Level Operational Trap Group Trap Name Description Severity LevelTrap Name Description Severity Level Flash Memory Trap Group Trap Name Description Severity LevelAlarm Host Table Tftp Trap Group Trap Name Description Severity LevelImage Trap Group Trap Name Description Severity Level Sntp Trap Group Trap Name Description Severity LevelAdvanced Configuration AP-700 User Guide Alarms Syslog Configuring Syslog Event NotificationsEvent Priority Description Syslog Messages Syslog Message Name Priority Severity DescriptionAdvanced Configuration AP-700 User Guide Rogue Scan 25 Preventing Rogue AP AttacksContinuous Scanning Mode Background Scanning ModeMulti-Band Scanning Rogue Scan Data CollectionClick Configure Alarms Rogue Scan Rogue Scan26 Rogue Scan Screen Bridge Spanning TreeAdvanced Configuration AP-700 User Guide Bridge Storm ThresholdIntra BSS Configuring Interfaces for Packet ForwardingPacket Forwarding Wireless Multimedia Extensions WME/Quality of Service QoS Click Configure QoS PolicyQoS Enabling QoS and Adding QoS policiesAdvanced Configuration AP-700 User Guide QoS Enter the Priority Mapping IndexClick Configure QoS Priority Mapping Priority MappingEnhanced Distributed Channel Access Edca STA Edca Table and AP Edca Table32 Edca Tables Advanced Configuration AP-700 User Guide QoS Radius Servers per Authentication Mode and per Vlan Radius ProfilesConfiguring Radius Profiles Radius Servers Enforcing Vlan Access ControlAdvanced Configuration AP-700 User Guide 35 Add Radius Server Profile 802.1x Authentication using Radius MAC Access Control Via Radius AuthenticationRadius Accounting Accounting Attributes Authentication Attributes101 102 Vlan Overview SSID/VLAN/Security103 104 Typical User Vlan Configurations Control Access to the APClick Configure SSID/VLAN/Security Mgmt Vlan Management VlanDisable Vlan Tagging Provide Access to a Wireless Host in the Same WorkgroupSecurity Profile Advanced Configuration AP-700 User Guide SSID/VLAN/Security Authentication ProcessWi-Fi Protected Access WPA/802.11i WPA2 107Authentication Protocol Hierarchy 108Configuring Security Profiles Click Configure SSID/VLAN/Security Security ProfileVLANs and Security Profiles 109Non Secure Station WEP Station802.1x Station WPA Station111 40 Security Profile Table Add Entries 112 Wireless MAC Access113 Configuring an SSID/VLAN with Vlan Tagging Disabled 11443 SSID/VLAN Edit Entries Screen Vlan Tagging Disabled 115Click SSID/VLAN/Security Wireless Configuring SSID/VLANs with Vlan Tagging Enabled116 45 SSID/VLAN Edit Entries Screen Vlan Tagging Enabled 117Broadcast Ssid and Closed System 118Monitoring 119Version Monitoring AP-700 User GuideIP/ARP Table Icmp Monitoring TabLearn Table Learn Table Monitoring TabRadius 124 Monitoring AP-700 User Guide Interfaces 125126 Station Statistics 127Monitoring AP-700 User Guide Station Statistics 128Introduction to File Transfer via Tftp or Http Commands129 Image Error Checking During File Transfer Tftp File Transfer GuidelinesHttp File Transfer Guidelines 130Update AP Update AP via TftpCommands AP-700 User Guide 131Commands AP-700 User Guide Update AP via Http Update AP via Http132 Commands AP-700 User Guide Retrieve File Retrieve FileRetrieve File via Tftp 133Retrieve File via Http 134Retrieve File via Http Command Screen Reset RebootCommands AP-700 User Guide Reboot 13 Help Link Configuration Screen 137 Help LinkTroubleshooting Troubleshooting ConceptsSymptoms and Solutions Connectivity IssuesBasic Software Setup and Configuration Problems Client Connection Problems Vlan Operation Issues Active Ethernet AEReset to Factory Default Procedure Recovery ProceduresForced Reload Procedure Download a New Image Using ScanTool Download ProcedurePreparing to Download the AP Image 143Download a New Image Using the Bootloader CLI 144Setting IP Address using Serial Port Initializing the IP Address using CLIHardware and Software Requirements Attaching the Serial Port CableRadius Authentication Server Related ApplicationsTftp Server 146Troubleshooting AP-700 User Guide Related Applications 147Command Line Interface CLI General NotesPrerequisite Skills and Knowledge Notation ConventionsCLI Error Messages Navigation and Special KeysCommand Line Interface CLI Variations Bootloader CLICommand Line Interface CLI AP-700 User Guide 150Operational CLI Commands CLI Command TypesExample 1. Display Command list Example 3. Display parameters for set and show Example 2. Display specific CommandsExample 3a. Display every parameter that can be changed Example 3b. Display parameters based on letter sequence Example 4. Display Prompts for Successive ParametersDone, exit, quit DownloadHelp HistoryPasswd 154Parameter Control Commands Show CLI CommandSearch 155Set CLI Command Configuring Objects that Require RebootSet and show Command Examples ExamplesExample 1 Set the Access Point IP Address Parameter Example 4 Enable, Disable, or Delete a table entry or rowExample 2 Create a table entry or row Example 3 Modify a table entry or rowExample 6 Show Individual and Table Parameters Example 5 Show the Group Parameters158 Using Tables and Strings Using StringsWorking with Tables 159Configuring the AP using CLI commands Set Basic Configuration Parameters using CLI CommandsLog into the AP using HyperTerminal Log into the AP using TelnetChange Passwords Set Network Names for the Wireless InterfaceSet System Name, Location and Contact Information 161Country Code 162Configure SSIDs Network Names, VLANs, and Profiles 163Other Network Settings Download an AP Configuration File from your Tftp ServerBackup your AP Configuration File Set up Auto ConfigurationConfigure the AP as a Dhcp Server Configure the DNS ClientEnable/Disable Closed System Operational ModeAutochannel Select ACS Shutdown/Resume Wireless Service Enable/Disable Super Mode 802.11a/g onlyEnable/Disable Turbo Mode 802.11a/g only Configure Antenna DiversityConfigure Management Ports Edit Management IP Access TableSet Communication Ports Configure Secure Socket Layer Https Set Telnet Session TimeoutsConfigure Serial Port Interface 169Create/Enable WDS Enable/Disable WDSSetup MAC Address Access Control Add an Entry to the MAC Access Control TableFigure A-17 Result of showradiustbl CLI Command 171 Disable Vlan Management Enable Vlan ManagementAdd a Entry to the Wifssid Table CLI Monitoring Parameters Parameter Tables 174Filtering Parameters 175Name Type Value Access CLI Parameter Set sysresettodefaultsSystem Parameters 176DNS Client for Radius Name Resolution Dhcp Server Parameters Name Type Value Access CLI ParameterNetwork Parameters 177Dhcp Server table for IP pools Dhcp Relay GroupDhcp Relay Server Table 178Link Integrity IP Target Table Sntp Parameters Name Type Value Access CLI Parameter179 Wireless Interface Parameters Interface ParametersCommon Parameters to 802.11a/b/g 180802.11a Only Parameters 181802.11b/g Only Parameters 802.11b Only Parameters182 For 802.11g-only mode For 802.11b/g modeFor 802.11b-only ModeWireless Distribution System WDS Parameters Wireless Interface SSID/VLAN/Profile ParametersChannel Blacklist Parameters 184Wireless Distribution System WDS Security Table Parameters Snmp Parameters Name Type Value Access CLI ParameterManagement Parameters 185186 Telnet Parameters Name Type Value Access CLI Parameter Http Parameters Name Type Value Access CLI Parameter187 Serial Port Parameters Name Type Value Access CLI Parameter Radius Based Management Access ParametersSSH Parameters 188Tftp Server Parameters IP Access Table Parameters189 Ethernet Filtering Table Filtering Parameters190 Proxy ARP Parameters Name Type Value Access CLI Parameter TCP/UDP Port FilteringTCP/UDP Port Filtering Table 191Alarms Parameters Name Type Value Access CLI Parameter Syslog Group 192Snmp Table Host Table Parameters Syslog ParametersSyslog Host Table 193Spanning Tree Priority and Path Cost Table Bridge Parameters194 Storm Threshold Table Intra BSS Subscriber BlockingPacket Forwarding Parameters 195Radius Server Configuration Parameters Radius ParametersGeneral Radius Parameters 196MAC Access Control Table Security ParametersSecurity Profile Table VLAN/SSID Parameters198 Iapp Parameters Name Type Value Access CLI Parameter Enabling QoS Name Type Value Access CLI ParameterConfiguring QoS Policies Other ParametersSpecifying the Mapping between 802.1p and 802.1D Priorities 200CLI Batch File Defining the QoS Policy used for a Wireless Interface Ssid201 Reboot Behavior Auto Configuration and the CLI Batch FileCLI Batch File Format and Syntax CLI Batch File Error Log 203Hex Ascii Character ChartCharact Equival Ent 204 Specifications Software FeaturesNumber of Stations per BSS Management FunctionsMedium Access Control MAC Functions Specifications AP-700 User Guide Software FeaturesAdvanced Bridging Functions Security FunctionsNetwork Functions Specifications AP-700 User Guide207 Hardware Specifications Mode Frequency Channel Product SKU Band Available Channels802.11b/g 802.11a Upper 149 153 157 161 ISM Band 165802.11a RF Performance 802.11a Data Rates Mbps RF Performance210 Online Support Technical SupportSoftware and Documentation Downloads Knowledgebase 211 Technical Support AP-700 User Guide Telephone Support Telephone SupportInternational 212 Statement of Warranty Warranty CoverageRepair or Replacement Limitations of WarrantyAsk a Question or Open an Issue Other InformationSearch Knowledgebase Other Adapter CardsProduct Model Numbers Regulatory Compliance215 Regulatory Compliance AP-700 User Guide Safety Information USA, Canada, & European Union216 Federal Communications Commission FCC 217Modifications 218Industry Canada IC 219European Union 220Country Certification/Reference No Regulatory Compliance Certifications Summary221