Logout Command, Authority None Syntax logout | Q-Logic 6140 guide

A

A – Command Reference Commands

Logout Command

Exits the command line interface and returns you to the login prompt.

Authority None

Syntax logout

Examples The following example shows the logout command:

QRouter (admin) #> logout

(none) login:

FI0154601-00 C

A-17

Image 149

Q-Logic 6140 manual Logout Command, Authority None Syntax logout, Examples The following example shows the logout command

Contents

SANbox 6140 Intelligent Storage Router SANbox 6140 Intelligent Storage Router User’s Guide Document Revision History SANbox 6140 Intelligent Storage Router User’s Guide Page Table of Contents Planning Removal/Replacement FI0154601-00 C Command Reference Configuring Chap Simple Network Management Protocol Snmp FI0154601-00 C List of Tables FI0154601-00 C Related Materials Intended Audience Safety Communications Statements CE Statement Federal Communications Commission FCC Class a Statement Vcci Class a Statement Laser Safety Information General Public License Electrostatic Discharge Sensitivity Esds PrecautionsAccessible Parts Preamble FI0154601-00 C FI0154601-00 C FI0154601-00 C No Warranty END of Terms and Conditions Ty Coon, President of Vice How to Apply These Terms to Your New Programs Training Technical SupportAvailability Contact Information General Description System Fault LED Amber Input Power LED GreenSystem Fault LED Blink Patterns Chassis LEDs Chassis Controls Maintenance ButtonReset a Router Reset IP Address Reset and Select Boot ImageEnable Dhcp Restore Factory Defaults Power on Before firmware Initialization Power OFFFibre Channel Ports Fibre Channel Port LEDs Fibre Channel Transceivers Ethernet Port-Management Gigabit Ethernet Port LEDs Serial Port Pin Identification Serial Port Devices Planning FC Performance Device AccessFibre Channel ISCSI ISCSI Performance Related performance characteristics include the followingBandwidth Latency T3 / DS-3 45 Mbits/Sec Performance TuningT1 / DS-1 1.554 Mbits/Sec Mbits/Sec OC-3 150 Mbits/Sec OC-1 50 Mbits/Sec OC-12 and Above 621 Mbits/Sec Multiple RoutersManagement Services Recovery Security FI0154601-00 C Management Workstation Requirements Site RequirementsManagement Workstation Environmental Conditions Power Requirements SANbox 6140 Router and Accessories Installing the SANbox 6140 Router Install the Transceivers Pre-installation Check ListPre-installation Checklist Mount the Router Connect the Management Workstation to the Router Configure the Management Workstation Configuring the Workstation Serial Port Setting the Workstation IP Address Windows Installation Install SANsurfer iSCSI/FC Router ManagerConnect the router to the power see Select the Intelligent Storage Routers icon Start SANsurfer iSCSI/FC Router Manager Linux InstallationFor Linux, enter the following command Configure the Router Connect the Router to AC Power Cable Devices to the Router Telnet 10.0.0.1 username guest password Using SANsurfer iSCSI/FC Router Manager to Install Firmware Firmware InstallationUsing the CLI to Install Firmware Enter your username and password. For example Type y to reboot the system Enter reboot. The following message displaysAt the ftp prompt, type bin to set binary mode. For example Following message displays This section describes the following conditions Chassis Diagnostics System Fault LED is On Power-On Self-Test DiagnosticsInput Power LED is Off LED Blink Patterns System Error Blink PatternHeartbeat Blink Pattern OK Operational Management Port IP Address Conflict Blink Pattern Over-Temperature Blink Pattern Recovering a Router FI0154601-00 C SFP Transceiver Removal and Replacement Removal/Replacement Removal Router Removal and ReplacementReplacement Introduction SANsurfer iSCSI/FC Router Manager SANsurfer Router Manager Main Window Sections Menu Bar View Menu Settings MenuFile Menu 7shows the Wizards drop-down menu Wizards Menu 8shows the Help drop-down menu Help Menu Action Menu Tool Bar SANsurfer iSCSI/FC Router Manager Action Menu 11shows the system tree System Tree Window 12 Component Information Status Icons and Text Discovered iSCSI Initiators RouterFC and iSCSI Ports ISCSI Presented Targets FC Discovered TargetsFC discovered target icons LUN icons Information SANbox 6140 Router Connectivity Basic Information 14 Information Tabbed Page Management Information Management Information FI0154601-00 C 15 Information Tabbed Page NTP Server Information NTP Server Information 16 Information Tabbed Page Security Information Security Information Snmp Management tabbed page provides the following options Snmp ConfigurationSnmp Management Snmp Trap Receivers Snmp Settings „ Link Status Port status, either Link Up or Link Down FC Ports 19 FC Port Advanced Configuration Tabbed Advanced Configuration Click OK to close the message box Save FC Port Settings Complete 20 FC Port Statistics Statistics ISCSI port display consists of three tabs „ Information ISCSI Ports „ Actual ISCSI Port Network SettingsISCSI Port Information FI0154601-00 C 22 Enable iSNS Server with IPv4 Address Enable iSNS Advanced iSCSI Port Parameters 24 Advanced Configuration Tabbed FI0154601-00 C Discovered iSCSI Initiators Initiator Information 25 Discovered iSCSI Initiator Tabbed Pages Chap Settings 26 LUN List Tabbed LUN List 27 FC Discovered Targets Information Tabbed FC Discovered Targets 28 LUN List Tabbed 29 iSCSI Presented Target List Tabbed ISCSI Presented Target List Tabbed 30shows the Discovered LUN Information tabbed Discovered LUN Information Tabbed FI0154601-00 C 31shows the LUN Presentation Information 1 tabbed LUN Presentation Information 1 and 2 Tabbed Pages 32 iSCSI Presented Targets Tabbed Pages ISCSI Presented Targets Information Tabbed 33 LUN Presentation Information Tabbed LUN Presentation Information Tabbed 34 Discovered LUN Information Tabbed Discovered LUN Information 35 Wizards Menu Wizards 36 iSCSI Port Selection Dialog Box Configuration Wizard Click Next „ IP Address „ Subnet Mask „ Gateway ISCSI Port IPv6 Settings Panel appears, as shown in Figure 38 iSCSI Port IPv6 Settings Panel Confirm Changes dialog box displays, as shown in Figure 39 Confirm Changes Dialog Box Wizard displays a Warning message, as shown in Figure Enter the password, then click OK 42 iSCSI Port Configuration Status Read the information, then click Finish System displays the Finish dialog box, as shown in Figure 44 Create an Initiator Dialog Box Add Initiator Wizard Security Check dialog box displays, as shown in Figure 45 Security Check Dialog Box 47 Router Selection Dialog Box FW Update Wizard 48 Firmware File Selection Dialog Box 49 Confirm Changes Dialog Box 51 Firmware Update Status Dialog Box-Progress Presentation Wizard 53 Device Selection Dialog Box LUN Mapping dialog box displays, as shown in Figure 54 LUN Mapping Dialog Box 55 Confirm Changes Dialog Box Finish dialog box displays, as shown in Figure 57 LUN Masking Configuration Status Dialog Box Click Finish to complete the Presentation wizard 59 Finish Dialog Box 60 Device Selection Dialog Box Presentation Unmap Wizard Confirm the LUN mapping changes by clicking Next 61 Select the Initiator for the LUN Presentation Dialog Box Click Finish to close the wizard 63 Security Check Dialog Box Logging on to a SAN Router Command Reference Modifying a Configuration Working with SAN Router ConfigurationsSaving and Restoring Router Configurations „ LUN Mapping, which uses the following command Save Router Configuration and Persistence Restore Router Configuration and Persistence CLI command syntax is as follows CommandsCommand Table A-1. Command Line Completion Authority Admin CommandSyntax Keywords Off Beacon CommandBeacon Clear logs or stats Clear CommandLogs Stats Syntax date Date CommandMMDDhhmmCCYY Keywords MMDDhhmmCCYY Keywords restore FRU CommandRestore save Syntax fru Displays a list of the commands and their syntax Help CommandExamples The following example shows the help command Authority None Syntax help Luns Lunmask Memory Mgmt Ntp Presentedtargets snmp Examples The following example shows the history command Displays a numbered list of the previously entered commandsHistory Authority None Syntax history Cleanup Image CommandImage Unpack file Initiator Initiator CommandAdd Mod Please select an Initiator from the list above q to quit Authority None Syntax logout Logout CommandExamples The following example shows the logout command Lunmask Lunmask Command Seagate Changes the guest and administrator passwords Password CommandExamples The following example shows the passwd command Syntax passwd Syntax ping Ping CommandExamples The following example shows the ping command Authority None Syntax quit Quit CommandExamples The following example shows the quit command Syntax reboot Reboot CommandRestarts the router firmware Authority Admin session Examples The following example shows the reboot command Reset Factory Command Traces Save Command Keywords chap Set CommandSyntax set Configures general router parameters Set Chap CommandFollowing example shows the set chap command Set chap Portnum Set FC CommandSet fc portnum FI0154601-00 C Configures an iSCSI port Set iSCSI CommandNumber of the iSCSI port to be configured Following example shows the set iscsi command FI0154601-00 C Configures iSNS parameters for an iSCSI port Set iSNS CommandNumber of the iSCSI port to be configured for iSNS Following example shows the set isns command Configures the router’s management port 10/100 Set Mgmt CommandFollowing example shows the set mgmt command Set mgmt Configures the NTP parameters Set NTP CommandFollowing example shows the set ntp command Set ntp Specifies the setting of the trap destinations Set Snmp CommandSet snmp Trapdestinations That have been changed Will now be saved Configures the general router parameters Set System CommandFollowing example shows the set system command Set system Configures the router’s Vlan parameters Set Vlan CommandFollowing example shows the set vlan command Set vlan Authority None Syntax show chap Show CommandInitiators fc or iscsi Initiatorslunmask Luns LuninfoPresentedtargets fc or iscsi Targets fc or iscsi Displays Chap configuration for iSCSI nodes Show Chap CommandExamples The following example shows the show fc command Authority None Syntax None Show FC CommandShow fc portnum Identifies the number of the FC port to display Keywords fc Show Initiators CommandSyntax show initiators fc Specifies the display of Fibre Channel initiators Syntax show initiatorslunmask Show Initiators LUN Mask CommandAuthority None Number of the iSCSI port to be displayed Show iSCSI CommandShow iscsi portnum IPv6 Link Local Show isns portnum Show iSNS CommandFollowing example shows the show isns command Examples The following example shows the show logs command Show Logs CommandDisplays the router event log Show logs Show luninfo Show Luninfo Command Examples The following example shows the show luns command Show LUNs CommandDisplays LUN information for each target Show luns Syntax show lunmask Show Lunmask Command Show mgmt Show Mgmt CommandFollowing example shows the show mgmt command Show ntp Show NTP Command Specifies the display of FC presented targets Show Presented Targets CommandSyntax show presentedtargets fc 10.3.5.66 Show snmp Show Snmp Command Show stats Show Stats CommandDisplays the router statistics FC and iSCSI 60362392962831 55036896842234 IP Fragment Rcvd Out of Order Show system Show System Command Show targets Show Targets CommandScsi Specifies the display of FC targets Following example shows the show targets iscsi command Keywords portnum Show Vlan CommandSyntax show vlan portnum Following example shows the target add command Target CommandTarget Not supported Targetmap TargetMap CommandFollowing example shows the targetmap add command Following example shows the targetmap rm remove command Syntax traceroute Traceroute Command CLI-Discovery Session-Bi-directional Chap Configuring Chap Select Mutual Authentication Click Advanced Select Chap Login InformationCLI-Discovery Session-Uni-directional Chap Click Discovery Use Set Chap Click OK Click OK. The initiator completes the normal loginCLI-Normal Session-Bi-directional Chap GUI-Discovery Session-Bi-directional Chap Click Advanced Configuration Select Enable ChapCLI-Normal Session-Uni-directional Chap Type the IQN name string GUI-Discovery Session-Uni-directional ChapClick Add Enter the address of the iSCSI port of the bridge Click OK Click OK. The initiator completes discovery Click Information Select Enable Chap Click Advanced Click Chap Login InformationGUI-Normal Session-Bi-directional Chap Click Advanced GUI-Normal Session-Uni-directional Chap Click OK Click OK. The initiator completes normal login FI0154601-00 C Table C-1. Application Modules-Informational Log Messages Application Modules Table C-2. Scsi Driver-Informational Log Messages ISCSI Driver Table C-3. Fibre Channel Driver-Informational Log Messages Fibre Channel Driver Table C-4. Application Module-Error Log Messages Error Log Messages Capacity Table C-4. Application Module-Error Log Messages FI0154601-00 C FI0154601-00 C Table C-5. iSCSI. Driver-Error Log Messages Log Messages Table C-6. Fibre Channel Driver-Error Log Messages Log Messages Error Log Messages User Modules Table C-7. User Modules-Error Log Messages Log Message System Table C-8. System-Error Log Messages Table C-9. iSCSI Driver-Fatal Log Messages Fatal Log Messages Table C-9. iSCSI Driver-Fatal Log Messages Table C-10. Fibre Channel Driver-Fatal Log Messages FC Driver Table C-10. Fibre Channel Driver-Fatal Log Messages Table C-11. System-Fatal Log Messages FI0154601-00 C Table D-1. Snmp Properties Snmp Properties Table D-2. Snmp Trap Configuration Parameters Snmp Trap Configuration QsrSerialNumber System InformationQsrHwVersion QsrSwVersion QsrNwPortEntry Network Port Table QsrNwPortIndex QsrNwPortRoleQsrNwPortAddressMode QsrIPAddressType Fibre Channel Port Table QsrFcPortRole QsrFcPortEntryQsrFcPortIndex QsrFcPortNodeWwn Sensor Table Sensor entry consists of the following sequence of objects QsrSensorEntryQsrSensorType QsrSensorIndex QsrUpperThreshold QsrSensorValueQsrLowerThreshold QsrSensorState QsrEventSeverity Notification ObjectsQsrEventDescription QsrEventTimeStamp Agent Shut Down Notification Agent Start Up NotificationNetwork Port Down Notification Fibre Channel Port Down Notification Generic Notification Sensor Notification FI0154601-00 C Index AC power CE statement Account, guest A-2 Index-2 FI0154601-00 C FI0154601-00 C Index-3 LUN FI0154601-00 C Index-5 Index-6 FI0154601-00 C TCP Index-8 FI0154601-00 C