Electrostatic Discharge Sensitivity Esds Precautions | Q-Logic 6140

A

1 – Introduction Electrostatic Discharge Sensitivity (ESDS) Precautions

Electrostatic Discharge Sensitivity (ESDS) Precautions

The assemblies used in the router chassis are ESD sensitive. Observe ESD handling procedures when handling any assembly used in the router chassis.

Accessible Parts

The following field replaceable units (FRUs) are supported by the SANbox 6140 router:

Small form-factor pluggable (SFP) optical transceivers

General Public License

QLogic SANbox routers are powered by the Linux operating system. A machine-readable copy of the Linux source code is available upon written request to the following address. A nominal fee will be charged for reproduction, shipping, and handling costs in accordance with the General Public License.

QLogic Corporation

26600 Aliso Viejo Parkway Aliso Viejo, CA 92656

Attention: Technical Support – Source Request

CAUTION!

Installation of software or files not authorized by QLogic will immediately and irrevocably void all warranty and service contracts on the affected units.

The following General Public License has been reproduced with permission from:

GNU General Public License Version 2, June 1991

Copyright 1989, 1991 Free Software Foundation, Inc.

59 Temple Place – Suite 330, Boston, MA 02111-1307, USA

FI0154601-00 C

1-5

Image 19

Q-Logic 6140 manual Electrostatic Discharge Sensitivity Esds Precautions, Accessible Parts, General Public License

Contents

SANbox 6140 Intelligent Storage Router SANbox 6140 Intelligent Storage Router User’s Guide Document Revision History SANbox 6140 Intelligent Storage Router User’s Guide Page Table of Contents Planning Removal/Replacement FI0154601-00 C Command Reference Configuring Chap Simple Network Management Protocol Snmp FI0154601-00 C List of Tables FI0154601-00 C Related Materials Intended Audience Safety Communications Statements CE Statement Federal Communications Commission FCC Class a Statement Vcci Class a Statement Laser Safety Information Accessible Parts Electrostatic Discharge Sensitivity Esds PrecautionsGeneral Public License Preamble FI0154601-00 C FI0154601-00 C FI0154601-00 C No Warranty END of Terms and Conditions Ty Coon, President of Vice How to Apply These Terms to Your New Programs Availability Technical SupportTraining Contact Information General Description Chassis LEDs Input Power LED GreenSystem Fault LED Amber System Fault LED Blink Patterns Reset a Router Maintenance ButtonChassis Controls Restore Factory Defaults Reset and Select Boot ImageReset IP Address Enable Dhcp Fibre Channel Port LEDs Power OFFPower on Before firmware Initialization Fibre Channel Ports Fibre Channel Transceivers Ethernet Port-Management Gigabit Ethernet Port LEDs Serial Port Pin Identification Serial Port Devices Planning ISCSI Device AccessFC Performance Fibre Channel Latency Related performance characteristics include the followingISCSI Performance Bandwidth T1 / DS-1 1.554 Mbits/Sec Performance TuningT3 / DS-3 45 Mbits/Sec Mbits/Sec OC-3 150 Mbits/Sec OC-1 50 Mbits/Sec Management Multiple RoutersOC-12 and Above 621 Mbits/Sec Services Recovery Security FI0154601-00 C Management Workstation Site RequirementsManagement Workstation Requirements Environmental Conditions Power Requirements SANbox 6140 Router and Accessories Installing the SANbox 6140 Router Mount the Router Pre-installation Check ListInstall the Transceivers Pre-installation Checklist Connect the Management Workstation to the Router Configure the Management Workstation Configuring the Workstation Serial Port Setting the Workstation IP Address Select the Intelligent Storage Routers icon Install SANsurfer iSCSI/FC Router ManagerWindows Installation Connect the router to the power see For Linux, enter the following command Linux InstallationStart SANsurfer iSCSI/FC Router Manager Configure the Router Connect the Router to AC Power Cable Devices to the Router Telnet 10.0.0.1 username guest password Enter your username and password. For example Firmware InstallationUsing SANsurfer iSCSI/FC Router Manager to Install Firmware Using the CLI to Install Firmware Following message displays Enter reboot. The following message displaysType y to reboot the system At the ftp prompt, type bin to set binary mode. For example This section describes the following conditions Chassis Diagnostics Input Power LED is Off Power-On Self-Test DiagnosticsSystem Fault LED is On OK Operational System Error Blink PatternLED Blink Patterns Heartbeat Blink Pattern Management Port IP Address Conflict Blink Pattern Over-Temperature Blink Pattern Recovering a Router FI0154601-00 C SFP Transceiver Removal and Replacement Removal/Replacement Replacement Router Removal and ReplacementRemoval Introduction SANsurfer iSCSI/FC Router Manager SANsurfer Router Manager Main Window Sections Menu Bar File Menu Settings MenuView Menu 7shows the Wizards drop-down menu Wizards Menu 8shows the Help drop-down menu Help Menu Action Menu Tool Bar SANsurfer iSCSI/FC Router Manager Action Menu 11shows the system tree System Tree Window 12 Component Information Status Icons and Text FC and iSCSI Ports RouterDiscovered iSCSI Initiators LUN icons FC Discovered TargetsISCSI Presented Targets FC discovered target icons Information SANbox 6140 Router Connectivity Basic Information 14 Information Tabbed Page Management Information Management Information FI0154601-00 C 15 Information Tabbed Page NTP Server Information NTP Server Information 16 Information Tabbed Page Security Information Security Information Snmp Management Snmp ConfigurationSnmp Management tabbed page provides the following options Snmp Trap Receivers Snmp Settings „ Link Status Port status, either Link Up or Link Down FC Ports 19 FC Port Advanced Configuration Tabbed Advanced Configuration Click OK to close the message box Save FC Port Settings Complete 20 FC Port Statistics Statistics ISCSI port display consists of three tabs „ Information ISCSI Ports ISCSI Port Information ISCSI Port Network Settings„ Actual FI0154601-00 C 22 Enable iSNS Server with IPv4 Address Enable iSNS Advanced iSCSI Port Parameters 24 Advanced Configuration Tabbed FI0154601-00 C Discovered iSCSI Initiators Initiator Information 25 Discovered iSCSI Initiator Tabbed Pages Chap Settings 26 LUN List Tabbed LUN List 27 FC Discovered Targets Information Tabbed FC Discovered Targets 28 LUN List Tabbed 29 iSCSI Presented Target List Tabbed ISCSI Presented Target List Tabbed 30shows the Discovered LUN Information tabbed Discovered LUN Information Tabbed FI0154601-00 C 31shows the LUN Presentation Information 1 tabbed LUN Presentation Information 1 and 2 Tabbed Pages 32 iSCSI Presented Targets Tabbed Pages ISCSI Presented Targets Information Tabbed 33 LUN Presentation Information Tabbed LUN Presentation Information Tabbed 34 Discovered LUN Information Tabbed Discovered LUN Information 35 Wizards Menu Wizards 36 iSCSI Port Selection Dialog Box Configuration Wizard Click Next „ IP Address „ Subnet Mask „ Gateway ISCSI Port IPv6 Settings Panel appears, as shown in Figure 38 iSCSI Port IPv6 Settings Panel Confirm Changes dialog box displays, as shown in Figure 39 Confirm Changes Dialog Box Wizard displays a Warning message, as shown in Figure Enter the password, then click OK 42 iSCSI Port Configuration Status Read the information, then click Finish System displays the Finish dialog box, as shown in Figure 44 Create an Initiator Dialog Box Add Initiator Wizard Security Check dialog box displays, as shown in Figure 45 Security Check Dialog Box 47 Router Selection Dialog Box FW Update Wizard 48 Firmware File Selection Dialog Box 49 Confirm Changes Dialog Box 51 Firmware Update Status Dialog Box-Progress Presentation Wizard 53 Device Selection Dialog Box LUN Mapping dialog box displays, as shown in Figure 54 LUN Mapping Dialog Box 55 Confirm Changes Dialog Box Finish dialog box displays, as shown in Figure 57 LUN Masking Configuration Status Dialog Box Click Finish to complete the Presentation wizard 59 Finish Dialog Box 60 Device Selection Dialog Box Presentation Unmap Wizard Confirm the LUN mapping changes by clicking Next 61 Select the Initiator for the LUN Presentation Dialog Box Click Finish to close the wizard 63 Security Check Dialog Box Logging on to a SAN Router Command Reference „ LUN Mapping, which uses the following command Working with SAN Router ConfigurationsModifying a Configuration Saving and Restoring Router Configurations Save Router Configuration and Persistence Restore Router Configuration and Persistence Table A-1. Command Line Completion CommandsCLI command syntax is as follows Command Keywords Admin CommandAuthority Syntax Beacon Beacon CommandOff Stats Clear CommandClear logs or stats Logs Keywords MMDDhhmmCCYY Date CommandSyntax date MMDDhhmmCCYY Syntax fru FRU CommandKeywords restore Restore save Authority None Syntax help Help CommandDisplays a list of the commands and their syntax Examples The following example shows the help command Luns Lunmask Memory Mgmt Ntp Presentedtargets snmp Authority None Syntax history Displays a numbered list of the previously entered commandsExamples The following example shows the history command History Unpack file Image CommandCleanup Image Mod Initiator CommandInitiator Add Please select an Initiator from the list above q to quit Examples The following example shows the logout command Logout CommandAuthority None Syntax logout Lunmask Lunmask Command Seagate Syntax passwd Password CommandChanges the guest and administrator passwords Examples The following example shows the passwd command Examples The following example shows the ping command Ping CommandSyntax ping Examples The following example shows the quit command Quit CommandAuthority None Syntax quit Examples The following example shows the reboot command Reboot CommandSyntax reboot Restarts the router firmware Authority Admin session Reset Factory Command Traces Save Command Syntax set Set CommandKeywords chap Set chap Set Chap CommandConfigures general router parameters Following example shows the set chap command Set fc portnum Set FC CommandPortnum FI0154601-00 C Following example shows the set iscsi command Set iSCSI CommandConfigures an iSCSI port Number of the iSCSI port to be configured FI0154601-00 C Following example shows the set isns command Set iSNS CommandConfigures iSNS parameters for an iSCSI port Number of the iSCSI port to be configured for iSNS Set mgmt Set Mgmt CommandConfigures the router’s management port 10/100 Following example shows the set mgmt command Set ntp Set NTP CommandConfigures the NTP parameters Following example shows the set ntp command Trapdestinations Set Snmp CommandSpecifies the setting of the trap destinations Set snmp That have been changed Will now be saved Set system Set System CommandConfigures the general router parameters Following example shows the set system command Set vlan Set Vlan CommandConfigures the router’s Vlan parameters Following example shows the set vlan command Initiatorslunmask Show CommandAuthority None Syntax show chap Initiators fc or iscsi Targets fc or iscsi LuninfoLuns Presentedtargets fc or iscsi Authority None Syntax Show Chap CommandDisplays Chap configuration for iSCSI nodes Examples The following example shows the show fc command Identifies the number of the FC port to display Show FC CommandNone Show fc portnum Specifies the display of Fibre Channel initiators Show Initiators CommandKeywords fc Syntax show initiators fc Authority None Show Initiators LUN Mask CommandSyntax show initiatorslunmask Show iscsi portnum Show iSCSI CommandNumber of the iSCSI port to be displayed IPv6 Link Local Following example shows the show isns command Show iSNS CommandShow isns portnum Show logs Show Logs CommandExamples The following example shows the show logs command Displays the router event log Show luninfo Show Luninfo Command Show luns Show LUNs CommandExamples The following example shows the show luns command Displays LUN information for each target Syntax show lunmask Show Lunmask Command Following example shows the show mgmt command Show Mgmt CommandShow mgmt Show ntp Show NTP Command Syntax show presentedtargets fc Show Presented Targets CommandSpecifies the display of FC presented targets 10.3.5.66 Show snmp Show Snmp Command Displays the router statistics FC and iSCSI Show Stats CommandShow stats 60362392962831 55036896842234 IP Fragment Rcvd Out of Order Show system Show System Command Specifies the display of FC targets Show Targets CommandShow targets Scsi Following example shows the show targets iscsi command Syntax show vlan portnum Show Vlan CommandKeywords portnum Not supported Target CommandFollowing example shows the target add command Target Following example shows the targetmap add command TargetMap CommandTargetmap Following example shows the targetmap rm remove command Syntax traceroute Traceroute Command CLI-Discovery Session-Bi-directional Chap Configuring Chap Click Discovery Click Advanced Select Chap Login InformationSelect Mutual Authentication CLI-Discovery Session-Uni-directional Chap CLI-Normal Session-Bi-directional Chap Click OK Click OK. The initiator completes the normal loginUse Set Chap CLI-Normal Session-Uni-directional Chap Click Advanced Configuration Select Enable ChapGUI-Discovery Session-Bi-directional Chap Click OK Click OK. The initiator completes discovery GUI-Discovery Session-Uni-directional ChapType the IQN name string Click Add Enter the address of the iSCSI port of the bridge Click Advanced Click Advanced Click Chap Login InformationClick Information Select Enable Chap GUI-Normal Session-Bi-directional Chap GUI-Normal Session-Uni-directional Chap Click OK Click OK. The initiator completes normal login FI0154601-00 C Table C-1. Application Modules-Informational Log Messages Application Modules Table C-2. Scsi Driver-Informational Log Messages ISCSI Driver Table C-3. Fibre Channel Driver-Informational Log Messages Fibre Channel Driver Table C-4. Application Module-Error Log Messages Error Log Messages Capacity Table C-4. Application Module-Error Log Messages FI0154601-00 C FI0154601-00 C Table C-5. iSCSI. Driver-Error Log Messages Log Messages Table C-6. Fibre Channel Driver-Error Log Messages Log Messages Error Log Messages User Modules Table C-7. User Modules-Error Log Messages Log Message System Table C-8. System-Error Log Messages Table C-9. iSCSI Driver-Fatal Log Messages Fatal Log Messages Table C-9. iSCSI Driver-Fatal Log Messages Table C-10. Fibre Channel Driver-Fatal Log Messages FC Driver Table C-10. Fibre Channel Driver-Fatal Log Messages Table C-11. System-Fatal Log Messages FI0154601-00 C Table D-1. Snmp Properties Snmp Properties Table D-2. Snmp Trap Configuration Parameters Snmp Trap Configuration QsrSwVersion System InformationQsrSerialNumber QsrHwVersion QsrNwPortEntry Network Port Table QsrIPAddressType QsrNwPortRoleQsrNwPortIndex QsrNwPortAddressMode Fibre Channel Port Table QsrFcPortNodeWwn QsrFcPortEntryQsrFcPortRole QsrFcPortIndex Sensor Table QsrSensorIndex QsrSensorEntrySensor entry consists of the following sequence of objects QsrSensorType QsrSensorState QsrSensorValueQsrUpperThreshold QsrLowerThreshold QsrEventTimeStamp Notification ObjectsQsrEventSeverity QsrEventDescription Fibre Channel Port Down Notification Agent Start Up NotificationAgent Shut Down Notification Network Port Down Notification Generic Notification Sensor Notification FI0154601-00 C Index AC power CE statement Account, guest A-2 Index-2 FI0154601-00 C FI0154601-00 C Index-3 LUN FI0154601-00 C Index-5 Index-6 FI0154601-00 C TCP Index-8 FI0154601-00 C