Manuals / Sharp / Computer Equipment / Printer

Sharp AR-350, AR_M280 operation manual Installation Requirements

Models: AR-350 AR_M280

1 118

Download 118 pages 55 Kb

Page 3

INSTALLATION REQUIREMENTS

INSTALLATION REQUIREMENTS

Improper installation may damage this product. Please note the following during initial installation and whenever the machine is moved.

1. The machine should be installed near an accessible power outlet for easy connection.

2. Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements. Also make certain the outlet is properly grounded.

● For the power supply requirements, see the name plate of the main unit.

3. Do not install your machine in areas that are: ● damp, humid, or very dusty

● exposed to direct sunlight

●poorly ventilated

●subject to extreme temperature or humidity

changes, e.g., near an air conditioner or heater.

4. Be sure to allow the required space around the machine for servicing and proper ventilation.

11-13/16" (30cm)

A small amount of ozone is produced within the copier

23-5/8" (60cm)

23-5/8" (60cm)

23-5/8" (60cm)

during operation. The emission level is insufficient to cause any health hazard.

NOTE:

The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 mg/m3) calculated as an 8 hr. time-weighted average concentration.

However, since the small amount that is emitted may have an objectionable odor, it is advisable to place the copier in a ventilated area.

0-1

Image 3

Sharp AR-350, AR_M280 operation manual Installation Requirements

Contents

LASER PRINTER Operation ManualMulti-function printer Page INSTALLATION REQUIREMENTS BATTERY DISPOSAL CAUTIONSCautions on laser SAFETY PRECAUTIONSCAUTIONS VORSICHT CLASS LASER PRODUCT LASER KLASSECAUTIONS VAROITUSFACSIMILE FEATURE Fax power switchLine connection CHAPTER CONTENTSCHAPTER BEFORE USING THE PRODUCT CHAPTER PRINTER BASIC SETTINGSCHAPTER APPENDIX CHAPTER TROUBLESHOOTING AND MAINTENANCECHAPTER PERIPHERAL UNITS CHAPTER KEY OPERATOR PROGRAMSPage CHAPTER BEFORE USING THE PRODUCTINTRODUCTION “Duplex module” INTRODUCTIONAbbreviated names of peripheral units “B/W scanner module/DSPF”INTRODUCTION Common to all features Manual paper feeding Print onto special paperAuto power shut-off mode MAIN FEATURES600 dpi high resolution printing Energy saving featureBypass tray part of duplex module/bypass tray*1 Exit tray*1 PART NAMES AND FUNCTIONSExterior Main switch See pageSide cover open knob PART NAMES AND FUNCTIONS InteriorFusing unit Duplex module side coverPart names and functions of peripheral units PART NAMES AND FUNCTIONSFinisher PART NAMES AND FUNCTIONSB/W scanner module/DSPF Upper exit tray extensionPART NAMES AND FUNCTIONS 1-10Other peripheral units Power supply unitDATA indicator 1-11PART NAMES AND FUNCTIONS Operation panel ERROR indicatorCUSTOM SETTINGS 1-12CONDITION SETTINGS Configuration settingsTo cancel the current print job and delete the print data 1-13To delete print data of a reserved job that waits for printing READY indicator 1-14Mode select keys and indicators PRINT key/READY indicator/DATA indicatorPRINT HOLD JOB LIST 1/1 CONDITION SETTINGS1-15 PART NAMES AND FUNCTIONS Touch panelCOPYING 1-16JOB QUEUE Job status screen common to print, copy, network scan, and fax modesMULTI SHOT Using the touch panelHow to use the touch panel 1-17Loading paper in paper tray Adjust the guide plates A and B in theLOADING PAPER 1-18Paper that can be used 1-19LOADING PAPER Paper available in paper trays Paper available in the bypass tray/multi purpose drawerPress the OK key to terminate the 9 setting Method of setting paper size and typeWhen using the operation panel on the main unit 1 “CUSTOM SETTINGS” will appear in the message displaySelect the paper tray for which setting is 3 to be made TRAY SETTINGS1 Press the CUSTOM SETTINGS key 2 Press the TRAY SETTINGS key1-22 SpecificationsHow to change the paper size Setting envelopes or postcardsUpper paper tray 1-23LOADING PAPER Loading paper in the stand/3 x 500 sheet paper drawer Specifications1 Pull out the large capacity tray 1-24Loading paper in the stand/MPD & 2000 sheet paper drawer Upper paper trayGENUINE SUPPLIES ADDING TONERSTORAGE OF SUPPLIES 1-25Page PRINTING FROM A COMPUTER CHAPTERSOFTWARE FOR WINDOWS CONNECTING TO A COMPUTER1. Using this machine as a local printer 2. Using this machine as a network printerWhen installation is complete, the message UNINSTALLING PRINTER UTILITIES3 On the Start menu, click “Run.” Enter the CD-ROM drive and setup 4 command. Then click the OK buttonStart Windows Insert the supplied CD-ROM into the CD- ROM drive Before installationOn the Start menu, select Settings and 3 then Printers Installing display fontsRight-click the installed printer driver and SETTING THE PRINTER DRIVEROn the Start menu, select Settings and 1 then Printers Right-click the installed printer driver and 2 select PropertiesClick the Help button under the menu 3 frame Environment required for accessing Web pagesAccessing Web pages and displaying help Open the Web browser on your computerSetting of Fax Destination Control Setting of E-mail Destination ControlSetting of FTP Destination Control Setting of Desktop Destination ControlNetwork Scanning Setup Set upNetwork Card Setup Password Setup2 Hold after print 5 Password1 Normal print 3 Hold before print2-10 Enter the fifth digit of the password and 5 press the OK keyUse the same procedure as step 5 to enter Select execution of printing, cancellationEnsure that the desired number of copies 8 is set When using the operation panel with touch panelEnter the password 2-11Printer account control 2-12CHAPTER PRINTER BASIC SETTINGS1. Printer configuration settings 2. Custom settings based on the customer’s operating conditions PagePress the or key to display the desired 5 setting MAKING CONFIGURATION SETTINGPress the MENU key to display the 1 configuration setting menu screen 3 setting itemTouch the desired setting on the setting MAKING CONFIGURATION SETTINGCONDITION SETTINGS Touch the CONDITION SETTINGS keySmoothing Main program settingsPCL settings PostScript settings4 Press the OK key Press the or key to select the desired 5 setting CUSTOM SETTINGSPress the MENU key to display the 1 custom settings menu screen Press the or key to select the desired 3 setting itemWhen setting is complete, press the CUSTOM SETTINGSPress the CUSTOM SETTINGS key when 2 its setting screenTotal count CUSTOM SETTINGS Setting itemsTray settings Auto tray switchingPage TROUBLESHOOTING AND MAINTENANCE This chapter describes misfeed removal, user maintenance, etcCHAPTER 1 Press the INFORMATION key Press the or key on the operation When using the operation panel on the main unitGeneral misfeed removal procedure MISFEED REMOVALMISFEED REMOVAL When using the operation panel with touch panelMisfeed removal guidance INFORMATION2 Remove the misfed paper Misfeed in the paper feed areaMisfeed in paper tray 1 Pull out the duplex moduleIf the machine is equipped with a stand Misfeed in the multi purpose drawerMisfeed in the stand/MPD & 2000 sheet paper drawer Misfeed in the stand/3 x 500 sheet paper drawer2 Remove the misfed paper Misfeed in the transport area, fusing area, and exit area3 Gently close the duplex module 1 Pull out the duplex moduleWhile holding the exit tray up, remove the 3 misfed paper Misfeed in the duplex moduleMisfeed in the bypass tray Raise the exit tray and open the cover of 2 the duplex moduleTROUBLESHOOTING ProblemSolution TROUBLESHOOTING ProblemSolution Solution 4-10TROUBLESHOOTING ProblemSupplementary explanation for printing 4-11USER MAINTENANCE Cleaning the scanner module4-12 CHAPTER PERIPHERAL UNITSDUPLEX MODULE Part namesSpecifications Set the bypass tray paper guides to the DUPLEX MODULELoading paper in the bypass tray duplex module/bypass tray only 1 Open the bypass trayUsing the exit tray mounted to the duplex module Setting the printer driver in accordance with your purposeSetting copy functions in accordance with your purpose Using the bypass trayDUPLEX MODULE Troubleshooting concerning the duplex module MAIL-BIN STACKER SpecificationsPart names MAIL-BIN STACKER Setting in the printer driverUsing the mail-bin stacker 2 driver setting screen when printing7 Close the paper guide Misfeed in the mail-bin stacker1 Open the top cover 6 Remove the misfed paperPart names FINISHERSupplies SpecificationsSort mode 5-10FINISHER Finisher functions5-11 FINISHER Using the finisher functionsUsing the stapling function from the printer feature Using the finisher functions in the copy mode3 box Staple cartridge replacement and staple jam removal5-12 1 Open the front cover 2 Turn the staple unit to face upReturn the lever to its original position 5-13Remove the paper from the stapler compiler Raise the lever at the end of the staple box2 Open the top cover 5-14Misfeed in the finisher Remove the misfed paper from the stapler 1 compilercover or paper guide of the finisher open? FINISHER Troubleshooting concerning the finisher5-15 The finisher is open or the top cover, frontFirst page front side 5-16Stapling position quick reference list FINISHERPart names SpecificationsSADDLE STITCH FINISHER 5-17Supplies 5-18Saddle stitch finisher functions SADDLE STITCH FINISHERSaddle stitch function Punch function only if a punch module is installed5-19 Staple sort modeUsing the finisher functions in the copy mode Using the saddle stitch finisher functionsUsing the punch function with a punch module installed as a peripheral unit1Open the front cover 2Pull out the stapler section Staple cartridge replacement and staple jam removalStaple cartridge replacement 5-2110Close the front cover 5-22Staple jam removal 8Insert the staple box11Return the lever to its original position 5-23Punch scrap disposal 9Remove the staple boxMisfeed in the saddle stitch finisher 8indication is seen when the stapling function has been used9compiler when the stapling function has been used 5-24Turn roller rotating knob D in the direction 13of the arrow 5-2511Remove the misfed paper Turn roller rotating knob D in the direction 12of the arrowCheck the punch position and set it again. See page Troubleshooting concerning the saddle stitch finisher5-26 SADDLE STITCH FINISHERbinding 5-27Stapling position quick reference list SADDLE STITCH FINISHERbinding 5-28Relation between print image and saddle stitch SADDLE STITCH FINISHERCHAPTER KEY OPERATOR PROGRAMSKey operator proguram list KEY OPERATOR PROGRAMSUse the same procedure as step 3 to enter the Using the key operator programsKEY OPERATOR PROGRAMS When using the operation panel on the main unitKEY OPERATOR PROGRAMS The display in shows the factory default settingKEY OPERATOR PROGRAMS RESTORE CONFIGURATIONUse the numeric keys to enter the five-digit 3password Supplementary explanation of key operation for key operator programsWhen using the operation panel with touch panel Press the CUSTOM SETTINGS keyNo print if account # invalid Cancel jobs 6 of invalid accounts Description of setting programsAuditor settings 1 Reset account Resetting accountToner save Toner save in printer mode Energy save Auto power shut-off timerAuto power shut-off Preheat modeDisabling of job priority operation Operation panel settings Auto clear settingBeep setting Language settingDisable paper desk drawers Device settingsDisable duplex unit Disable stapler unit6-11 System settings default settingsDisable notice page printing Disable test page printingPDL for parallel port Parallel port emulation switching System settings Interface settingsPDL for network port Network port emulation switching I/O timeoutEnableTCP/IP System settings network settings1 Reset the NIC IP address setting1 Restore configuration System settings initialize/store settings1 Restore factory defaults 1 Store current configurationAPPENDIX CHAPTERPage Specifications PRINTER SPECIFICATIONSList of principal printer functions LIST OF COMBINATION OF PERIPHERAL UNITS Disabling notice page and separator sheet printing Notice page printingIn case of landscape orientation in mm PRINT AREAThe print area of this product is shown below In case of portrait orientation in mm