
Inserting a scene from a VCR
To change the insert end pointPress ZERO SET MEMORY again after step 5 to erase the ZERO SET MEMORY indicator and begin from step 3.
В‚Â‰ÂÌË ˝ÔËÁÓ‰‡ Ò КВМ
ДÎя ËÁÏÂÌÂÌËя ÏÂÒÚ‡ ÍÓ̈‡ ‚ÒÚ‡‚ÍËН‡ÊÏËÚ ÍÌÓÔÍÛ ZERO SET MEMORY ¢ ‡Á ÔÓÒΠÔÛÌÍÚ‡ 5 ‰Îя Û‰‡ÎÂÌËя Ë̉Ë͇ˆËË
ZERO SET MEMORY Ë Ì‡˜ÌËÚÂ Ò ÔÛÌÍÚ‡ 3.
Using the Remote Commander
Press REC and the button on its right simultaneously, then immediately press Xin the step 5 and 6. And in the step 7, press X at the scene where you want to start recording from.
Note
The picture and sound recorded on the section between the insert start and end points will be erased when you insert the new scene.
If you insert scenes on the tape recorded with other camcorder
(including other
The picture and sound may be distorted. We recommend that you insert scenes on a tape recorded with your camcorder.
When the inserted picture is played back The picture and sound may be distorted at the end of the inserted section. This is not a malfunction.
The sound at the start point and the end point may be distorted in the LP mode.
To insert a scene without setting the insert end point
Skip step 3 and 4. Press x when you want to stop inserting.
If you press FN
The ZERO SET MEMORY indicator is not displayed.
Н‡ÊÏËÚ ÍÌÓÔÍÛ REC Ë ÍÌÓÔÍÛ ÒÔ‡‚‡ ÓÚ Ì ӉÌÓ‚ÂÏÂÌÌÓ, ‡ Á‡ÚÂÏ Ò‡ÁÛ Ê ̇ÊÏËÚ ÍÌÓÔÍÛ X ‚ ÔÛÌÍÚ 5 Ë 6. А ‚ ÔÛÌÍÚ 7 ̇ÊÏËÚ ÍÌÓÔÍÛ X ‚ ̇˜‡Î ˝ÔËÁÓ‰‡, Ò ÍÓÚÓÓ„Ó В˚ ıÓÚËÚ ̇˜‡Ú¸ Á‡ÔËÒ¸.
ПËϘ‡ÌËÂ
ИÁÓ·‡ÊÂÌËÂ Ë Á‚ÛÍ, Á‡ÔËÒ‡ÌÌ˚ ̇ Û˜‡ÒÚÍ ÏÂÊ‰Û ÏÂÒÚÓÏ Ì‡˜‡Î‡ Ë ÍÓ̈‡ ‚ÒÚ‡‚ÍË, ÏÓ„ÛÚ ·˚Ú¸ ÒÚÂÚ˚, ÍÓ„‰‡ В˚ ‚ÒÚ‡‚ÎяÂÚ ÌÓ‚˚È ˝ÔËÁÓ‰.
ЕÒÎË В˚ ‚ÒÚ‡‚ÎяÂÚ ˝ÔËÁÓ‰˚ ̇ ÎÂÌÚÛ, Á‡ÔËÒ‡ÌÌÛ˛ ̇ ‰Û„ÓÈ ‚ˉÂÓ͇Ï (‚Íβ˜‡я ‰Û„Û˛
ВÒÎÛ˜‡Â ‚ÒÚ‡‚ÍË ËÁÓ·‡ÊÂÌËя ‚Ó ‚ÂÏя ‚ÓÒÔÓËÁ‚‰ÂÌËя ИÁÓ·‡ÊÂÌËÂ Ë Á‚ÛÍ ÏÓ„ÛÚ ·˚Ú¸ ËÒ͇ÊÂÌ˚ ‚
ÍÓ̈ ‚ÒÚ‡‚ÎÂÌÌÓ„Ó Û˜‡ÒÚ͇. ЭÚÓ Ì я‚ÎяÂÚÒя ÌÂËÒÔ‡‚ÌÓÒÚ¸˛.
З‚ÛÍ ‚ ̇˜‡Î¸ÌÓÈ ÚÓ˜ÍÂ Ë ÍÓ̘ÌÓÈ ÚӘ͠ÏÓÊÂÚ ·˚Ú¸ ËÒ͇ÊÂÌ ‚ ÂÊËÏ LP.
ДÎя ‚ÒÚ‡‚ÍË ˝ÔËÁÓ‰‡ ·ÂÁ ÛÒÚ‡ÌÓ‚ÍË ÏÂÒÚ‡ ÍÓ̈‡ ‚ÒÚ‡‚ÍË
ПÓÔÛÒÚËÚ ÔÛÌÍÚ 3 Ë 4. Н‡ÊÏËÚ ÍÌÓÔÍÛ x, ÍÓ„‰‡ В˚ ıÓÚËÚ ÓÒÚ‡ÌÓ‚ËÚ¸ ‚ÒÚ‡‚ÍÛ.
ЕÒ‰Ë В˚ ̇ÊÏÂÚ ÍÌÓÔÍÛ FN И̉Ë͇ÚÓ ZERO SET MEMORY ÓÚÓ·‡Ê‡Ú¸Òя Ì ·Û‰ÂÚ.
74