Toshiba Three-phase 200V class 0.1 to 2.2kW Compliance with Peripheral devices, Aic, Cc/J

E6581090

9.2.3Compliance with Peripheral devices

Use the UL listed fuses at connecting to power supply.

Refer to the instruction manual about selecting the rating of them.

Short circuit test is performed under the condition of the power supply short-circuit currents in below.

These currents and fuse currents depend on the drive motor capacities.

		Table 4. AIC and fuse
Voltage class	Capacity of	Inverter model	AIC	Maximum	Fuse class and
	applicable		(Interrupting	input
					currents (A)
	motor (kW)		capacity)	voltage (V)
Single-phase	0.1	VFNC1S-1001P	AIC 1000A	120	CC/J	6 max
	0.2	VFNC1S-1002P	AIC 1000A	120	CC/J	8 max
100V class	0.4	VFNC1S-1004P	AIC 1000A	120	CC/J	12 max
	0.75	VFNC1S-1007P	AIC 1000A	120	CC/J	22 max
	0.2	VFNC1S-2002P(L)	AIC 1000A	240	CC/J	4 max
Single-phase	0.4	VFNC1S-2004P(L)	AIC 1000A	240	CC/J	8 max
	0.75	VFNC1S-2007P(L)	AIC 1000A	240	CC/J	12 max
200V class
	1.5	VFNC1S-2015P(L)	AIC 5000A	240	CC/J	22 max
	2.2	VFNC1S-2022P(L)	AIC 5000A	240	CC/J	30 max
	0.1	VFNC1-2001P	AIC 1000A	240	CC/J	3 max
Three-phase	0.2	VFNC1-2002P	AIC 1000A	240	CC/J	3 max
	0.4	VFNC1-2004P	AIC 1000A	240	CC/J	5 max
200V class	0.75	VFNC1-2007P	AIC 1000A	240	CC/J	8 max
							9
	1.5	VFNC1-2015P	AIC 5000A	240	CC/J	15 max
	2.2	VFNC1-2022P	AIC 5000A	240	CC/J	20 max

Table 5. Power supply short-circuit current and input voltage

Input voltage	Drive motor	Power supply short-circuit current and maximum input voltage
100V	Up to 0.75 kW	Suitable For Use On A Circuit Capable Of Delivering Not More Than 1,000A rms
		Symmetrical	Amperes, 120 Volts Maximum When Protected by CC/J Class Fuses.
	Up to 0.75 kW	Suitable For Use On A Circuit Capable Of Delivering Not More Than 1,000A rms
		Symmetrical	Amperes, 240 Volts Maximum When Protected by CC/J Class Fuses.
200V
	1.5 kW and over	Suitable For Use On A Circuit Capable Of Delivering Not More Than 5,000A rms
		Symmetrical	Amperes, 240 Volts Maximum When Protected by CC/J Class Fuses.

9.2.4Motor thermal protection

Selects the electronic thermal protection characteristics that fit with the ratings and characteristics of the motor. In case of multi motor operation with one inverter, thermal relay should be connected to each motor.

I-7