Manuals / Toshiba / Marine Equipment / Marine Battery

Toshiba Single-phase 200V class 0.2 to 2.2kW instruction manual Control circuit terminal block

Models: Single-phase 100V class 0.1 to 0.75kW Three-phase 200V class 0.1 to 2.2kW Single-phase 200V class 0.2 to 2.2kW

1 144

Download 144 pages 31.84 Kb

Page 18

E6581090

VFNC1S-2015PL～2022PL

[Main circuit input terminals]

1

[Main circuit output terminals]

2) Control circuit terminal block

The same type of terminal board is provided for all models.

Sizes of connectable wires Solid wire: 0.3 to 1.5 (mm2) Stranded wire: 0.3 to 1.5 (mm2)

(AWG: 262 to 16)

Sheath strip length: 6 mm

Driver bit size: 3.5 ⋅ 0.6 mm

Sizes of connectable wires Solid wire: 0.3 to 1.5 (mm2) Stranded wire: 0.3 to 1.25 (mm2)

(AWG: 262 to 16)

Sheath strip length: 5 mm

Driver bit size: 2.5 ⋅ 0.4 mm

For details of each terminal, see 2.3.2.

A-8

Image 18

Toshiba Single-phase 200V class 0.2 to 2.2kW, Single-phase 100V class 0.1 to 0.75kW Control circuit terminal block

Contents

Industrial Inverter How to set a setup parameter ENTSafety precautions Limits in purposeGeneral operation Transportation ‚ Installation WiringOperations When retry function is selected inverter Attach caution labels ― Contents ― 10.1 Contents of the product code Read firstCheck purchased product Name and function of each part Operation keypad panelFront panel Self-up terminal block VFNC1-2001P～2007P VFNC1-2015P～2022P VFNC1S-1007P VFNC1S-2015P～2022P Control circuit terminal block Same type of terminal board is provided for all modelsMotors Inverters Leakage current from the inverter main unit DisposalWhat to do about leak current Effects of leakage current across groundAffects of leakage current across lines RemediesInstallation Installation environment Resistor How to install Installation locationVFNC1S VFNC1Installing more than one unit in a cabinet Connection Standard connections Control and main power supplyWiring Preventing radio noiseStandard connection diagram VF-nC1When using V1/S3 terminal as a logic input terminal H DC reactor ＊ DCL option P0 ＊4 DC reactor＊5 Main circuit terminals Power supply and motor connectionsDescription of terminals Connections with peripheral equipmentControl circuit terminals sink logic common CC VI/S3FLA Sink logic negative common/source logic positive commonOUT FLBSwitching the input terminal logic between sink and source Simple operation Run / stop SettingSimple operation of the VF-nC1 FrequencyRUN Motor starts Motor stops slowdown stop Short F and CC terminals run forwardSetting the frequency using the operation panel Hoqf Setting the frequency using external potentiometerSetting the frequency by serial communications Hoqf Setting the frequency using input voltageSetting the frequency using current input 4-20mA Basic VF-nC1 operations How to set parameters Setup parametersHow to set a setup parameter KP KVHow to set the basic parameters Steps in key entry for basic parametersHow to set extended parameters Steps in key entry for extended parametersCWH GPF HTHPress the Enter key to display the setting of the parameter ITW CEEParameters that cannot be changed while running Returning all parameters to standard default setting KpkvFrequency setting mode selection Selecting an operation modeCommand mode selection SettingsMeter setting and adjustment FunctionFM/OUT Adjustment scale with meter adjustment HO parameterAdjusting the meter in inverter stop state HounStandard default setting HT Forward/reverse selection Operation panel Setting acceleration/deceleration timeSelecting forward and reverse runs operation panel only CEE Acceleration time 1 s FGE Deceleration time 1 sUpper limit and lower limit frequencies Parameter settingMaximum frequency HJ Maximum frequency HzSelecting control mode Base frequency Base frequency 1 Hz XD Setting the electronic thermal Setting of motor electronic thermal protection level 1 VJTExplanation of terms Using a VF motor motor for use with inverter Inverter over load characteristicsSetting the motor electronic thermal protection level 1 VJT Preset speed frequency setting Preset speed operation speeds in 15 stepsSetting method Run/stop Motor 150%-overload time limit HUsing other speed commands with preset speed command EoqfExtended parameters Output signal-related parametersOutput terminal setting FM/OUT terminal functions selectionParameter for specifying a frequency OFFParameters related to terminal function selection Setting of contact input terminal function Connection methodSwitching between control logics Sink/Source selection Jog runSetting of output terminal functions 40MCHG Setting of switching terminalsBasic parameters OFFAnalog signals for frequency setting Setting frequency command characteristicsAdjustment of 0~10Vdc voltage input Adjustment of 4~20mAdc current input 0 voltage input Starting frequency Starting frequency setting Hz Operation frequencyDC braking PWM carrier frequency Preset speed operation frequencies 8 to ～ H Preset speed operation frequencies 8 to 15 Hz Jump frequency Hz Jump width HzTrip-less intensification During restart operation, the message  is displayed Start of motor during coasting Motor speed search functionApplication to a crane or hoist Inverter, motor and machine ・GRJQ ・QEC・QEN ・GTTExternal connection Setting the PI control parameterPerforming PI control Types of PI control interfacesAdjusting the PI control gain level Adjusting an analog command voltageImproving torque and speed characteristics Optimizing control characteristics 2 switching frequencySwitching between acceleration and deceleration Acceleration/decelerationCurrent stall setting Stall prevention level Protection functionsExternal trip stop by means of a terminal Emergency stop by means of the operation panel ①Press the Stop key Gqhh will blinkOver-torque alarm    Undervoltage trip Under voltage trip selection FM/OUT terminal selection 1 12 OT over-torque detectionOperation panel parameters Setting methodsCanceling the setting Analog input disconnection detection Communication function common serial Changing the standard monitoring item Selection of monitor display selection Data transmission specifications 16.1 Using RS232C/RS485 conversion unitsSetting up the communications function Communications parameters Common serial optionsFree notes Free notesSetting the operation frequency Variety of operationRSS4 Setting the operation mode Status monitor mode Setting procedure eg. operation at 60HzMonitoring the operation status MON Display of trip information ⇔ Abstract Taking measures to satisfy the CE / UL / CSACompliance with CE Marking EMC directive【Ex. Countermeasure main circuit wiring】 Compliance with EMC directive Model, noise filter insideEMFA2015Z Models without EMI filtersEMFA2006Z EMFAS2011Z【Operating with external signals】【Accessories for countermeasure】【Apply if needed】Compliance with Low voltage directive Compliance with InstallationCompliance with UL Standard and CSA Standard Compliance with ConnectionAIC Compliance with Peripheral devicesMotor thermal protection CC/JSelection of wiring materials and devices Peripheral devicesSelection of wiring devices Magnetic contactor in the primary circuit Installation of a magnetic contactorInstallation of an overload relay Magnetic contactor in the secondary circuit11.2 Basic parameters Table of parameters and data11.1 User parameters NN－WNUT VJTQNO NNWNExtended parameters Input/output parametersLOW Frequency parameters NN-WNOperation mode parameters Torque boost parametersAcceleration/deceleration time parameters Factory setting parameter Operation panel parametersCommunication parameters Default settings by inverter rating Table of input terminal functions +SS3+AD2 +SS1+AD2+SS2+AD2 +SS4+AD2Table of output terminal functions Order of precedence of combined functions Specifications Models and their standard specificationsStandard specifications Self-cooling Forced LED External dimensions/weights External dimensions/weightsExternal dimensions Trip causes/warnings and remedies CEE QERFGE QER GRJ GRJ Oqhh CPUQHH TVTUvqr UQUK Restoring the inverter from a trip If the motor does not run while no trip message is displayed YESHow to determine the causes of other problems Inspection and maintenance Regular inspectionCheck points Periodical inspection Check itemsReplacement of expendable parts Standard replacement cycles of principal partsMaking a call for servicing Keeping the inverter in storageWarranty Disposal of the inverter Toshiba