Toshiba Single-phase 200V class 0.2 to 2.2kW instruction manual Peripheral devices

E6581090

10. Peripheral devices

Warning

•If you take the power supply from an outlet, do not over the outlet’s rated current. That could emit the outlet and may result in an ignition.

Prohibited

•When using wiring materials and their optional devices for the inverter, they must

	be installed in a cabinet.
Mandatory	Failure to do so can lead to risk of electric shock and can result in death or
	serious injury.

•Connect earth cables securely. Failure to do so can lead to risk of electric

shock or fire in case of a failure, short-circuit or leak current.

Be Grounded

10.1Selection of wiring materials and devices

Voltage	Capacity of			Wire size
	applicable	Inverter model	Main circuit	DC reactor
class	motor				Grounding cable
			(See Note 1.)	(optional)
	(kW)
Single-ph	0.1	VFNC1S-1001P	AWG 14 / 2.0 mm2	-	AWG 12 / 3.5 mm2
	0.2	VFNC1S-1002P	AWG 14 / 2.0 mm2	-	AWG 12 / 3.5 mm2
ase 100V
	0.4	VFNC1S-1004P	AWG 14 / 2.0 mm2	-	AWG 12 / 3.5 mm2
class	0.75	VFNC1S-1007P	AWG 14 / 3.5 mm2	-	AWG 12 / 3.5 mm2
						10
	0.2	VFNC1S-2002P(L)	AWG 14 / 2.0 mm2	AWG 16 / 1.25 mm2	AWG 12 / 3.5 mm2
Single-ph	0.4	VFNC1S-2004P(L)	AWG 14 / 2.0 mm2	AWG 16 / 1.25 mm2	AWG 12 / 3.5 mm2
ase 200V	0.75	VFNC1S-2007P(L)	AWG 14 / 2.0 mm2	AWG 14 / 2.0 mm2	AWG 12 / 3.5 mm2
class	1.5	VFNC1S-2015P(L)	AWG 10 / 3.5 mm2	AWG 14 / 2.0 mm2	AWG 12 / 3.5 mm2
	2.2	VFNC1S-2022P(L)	AWG 10 / 5.5 mm2	AWG 14 / 2.0 mm2	AWG 10 / 5.5 mm2
	0.1	VFNC1-2001P	AWG 14 / 2.0 mm2	AWG 16 / 1.25 mm2	AWG 12 / 3.5 mm2
Three-ph	0.2	VFNC1-2002P	AWG 14 / 2.0 mm2	AWG 16 / 1.25 mm2	AWG 12 / 3.5 mm2
	0.4	VFNC1-2004P	AWG 14 / 2.0 mm2	AWG 16 / 1.25 mm2	AWG 12 / 3.5 mm2
ase 200V	0.75	VFNC1-2007P	AWG 14 / 2.0 mm2	AWG 14 / 2.0 mm2	AWG 12 / 3.5 mm2
class	1.5	VFNC1-2015P	AWG 10 / 2.0 mm2	AWG 14 / 2.0 mm2	AWG 12 / 3.5 mm2
	2.2	VFNC1-2022P	AWG 10 / 2.0 mm2	AWG 14 / 2.0 mm2	AWG 12 / 3.5 mm2

Note 1: Sizes of the wires connected to the input terminals R, S and T and the output terminals U, V and W when the length of each wire does not exceed 30m.

Note 2: For the control circuit, use shielded wires 0.75 mm2 or more in diameter.

Note 3: For grounding, use a cable with a size equal to or larger than the above.

Note 4: When using a crimp terminal, cover its caulked part with a tube or use an insulated terminal.

J-1