Manuals / Toshiba / Marine Equipment / Marine Battery

Toshiba Single-phase 200V class 0.2 to 2.2kW Operation panel parameters, Communication parameters

Models: Single-phase 100V class 0.1 to 0.75kW Three-phase 200V class 0.1 to 2.2kW Single-phase 200V class 0.2 to 2.2kW

1 144

Download 144 pages 31.84 Kb

Page 120

E6581090

•Operation panel parameters

		Communication			Minimum setting		Default	User
	Title	Communication	Function	Unit	unit Panel/	Adjustment range	Default	User	Reference
	Title	No.	Function	Unit	unit Panel/	Adjustment range	setting	setting	Reference
		No.			Communication		setting	setting
					Communication
	H	0700	Prohibition of change	-	-	0:Permitted (EOQF,	0		6.15.1
			parameter settings			HOQF cannot be
						changed during
						operation.)
						1:Prohibited
						2:Permitted (EOQF,
						HOQF also can be
						changed during
						operation)
						3:Prohibited (except for
						panel frequency
						setting.)
						4:0 + panel emergency
						stop prohibited
						5:1 + panel emergency
						stop prohibited
						6:2 + panel emergency
						stop prohibited
						7:3 + panel emergency
						stop prohibited
	H	0701	Unit selection	-	-	0:0%, Hz (no change)	0		6.15.2
						1:% to A/V
						2:Free unit selection
						enabled (H)
						3:% to A/V, Free unit
						selection enabled
						(H)
	H	0702	Frequency units	-	0.01/0.01	0.01-200.0	1.00		6.15.2
			selection
	H	0710	Selection of monitor	-	-	0:Operation frequency	0		6.15.3
			display selection			(Hz/free unit)
						1:Frequency
						command (Hz/free
						unit)
						2:Output current (%/A)

•Communication parameters

		Communication			Minimum setting		Default	User
	Title	Communication	Function	Unit	unit Panel/	Adjustment range	Default	User	Reference
	Title	No.	Function	Unit	unit Panel/	Adjustment range	setting	setting	Reference
					Communication
	H	0800	Communication baud	-	-	0:1200bps	3		6.16
			rate			1:2400bps
						2:4800bps
						3:9600bps
						4:19200bps
	H	0801	Parity	-	-	0:NON (non-parity)	1		6.16
						1:EVEN (even parity)
						2:ODD (odd parity)
	H	0802	Inverter number	-	1	0-99	0		6.16
	H	0803	Communication error	s	1/1	0 (Disabled),	0		6.16
			trip time			1 - 100 (s)
	H	0880	Free notes	-	1	0～65535 *	0		6.16

*Adjustment range of the above mention can set by the computer on the network. The operation panel can set to the maximum 9999.

•Factory setting parameter

		Communication			Minimum setting		Default	User
	Title	Communication	Function	Unit	unit Panel/	Adjustment range	Default	User	Reference
	Title	No.	Function	Unit	unit Panel/	Adjustment range	setting	setting	Reference
					Communication
*	H	0990	For factory setting	-	-	-	0		-

*This function is effective after software version V110.

K-7

11

Image 120

Toshiba Single-phase 200V class 0.2 to 2.2kW instruction manual Operation panel parameters, Communication parameters

Contents

Industrial Inverter How to set a setup parameter ENTSafety precautions Limits in purposeGeneral operation Transportation ‚ Installation WiringOperations When retry function is selected inverter Attach caution labels ― Contents ― 10.1 Contents of the product code Read firstCheck purchased product Name and function of each part Operation keypad panelFront panel Self-up terminal block VFNC1-2001P～2007P VFNC1-2015P～2022P VFNC1S-1007P VFNC1S-2015P～2022P Control circuit terminal block Same type of terminal board is provided for all modelsMotors Inverters Disposal What to do about leak currentLeakage current from the inverter main unit Effects of leakage current across groundAffects of leakage current across lines RemediesInstallation Installation environment Resistor How to install Installation locationVFNC1S VFNC1Installing more than one unit in a cabinet Connection Control and main power supply WiringStandard connections Preventing radio noiseStandard connection diagram VF-nC1When using V1/S3 terminal as a logic input terminal H DC reactor ＊ DCL option P0 ＊4 DC reactor＊5 Power supply and motor connections Description of terminalsMain circuit terminals Connections with peripheral equipmentControl circuit terminals sink logic common CC VI/S3Sink logic negative common/source logic positive common OUTFLA FLBSwitching the input terminal logic between sink and source Simple operation Setting Simple operation of the VF-nC1Run / stop FrequencyRUN Motor starts Motor stops slowdown stop Short F and CC terminals run forwardSetting the frequency using the operation panel Hoqf Setting the frequency using external potentiometerSetting the frequency by serial communications Hoqf Setting the frequency using input voltageSetting the frequency using current input 4-20mA Basic VF-nC1 operations How to set parameters Setup parametersHow to set a setup parameter KP KVHow to set the basic parameters Steps in key entry for basic parametersHow to set extended parameters Steps in key entry for extended parametersCWH GPF HTHPress the Enter key to display the setting of the parameter ITW CEEParameters that cannot be changed while running Returning all parameters to standard default setting KpkvSelecting an operation mode Command mode selectionFrequency setting mode selection SettingsMeter setting and adjustment FunctionAdjustment scale with meter adjustment HO parameter Adjusting the meter in inverter stop stateFM/OUT HounStandard default setting Setting acceleration/deceleration time Selecting forward and reverse runs operation panel onlyHT Forward/reverse selection Operation panel CEE Acceleration time 1 s FGE Deceleration time 1 sParameter setting Maximum frequencyUpper limit and lower limit frequencies HJ Maximum frequency HzSelecting control mode Base frequency Base frequency 1 Hz XD Setting the electronic thermal Setting of motor electronic thermal protection level 1 VJTExplanation of terms Using a VF motor motor for use with inverter Inverter over load characteristicsSetting the motor electronic thermal protection level 1 VJT Preset speed operation speeds in 15 steps Setting method Run/stopPreset speed frequency setting Motor 150%-overload time limit HUsing other speed commands with preset speed command EoqfOutput signal-related parameters Output terminal settingExtended parameters FM/OUT terminal functions selectionParameter for specifying a frequency OFFParameters related to terminal function selection Setting of contact input terminal function Connection methodSwitching between control logics Sink/Source selection Jog runSetting of output terminal functions Setting of switching terminals Basic parameters40MCHG OFFAnalog signals for frequency setting Setting frequency command characteristicsAdjustment of 0~10Vdc voltage input Adjustment of 4~20mAdc current input 0 voltage input Starting frequency Starting frequency setting Hz Operation frequencyDC braking Preset speed operation frequencies 8 to ～ H Preset speed operation frequencies 8 to 15 HzPWM carrier frequency Jump frequency Hz Jump width HzTrip-less intensification During restart operation, the message  is displayed Start of motor during coasting Motor speed search functionApplication to a crane or hoist Inverter, motor and machine ・QEC ・QEN・GRJQ ・GTTSetting the PI control parameter Performing PI controlExternal connection Types of PI control interfacesAdjusting the PI control gain level Adjusting an analog command voltageImproving torque and speed characteristics Optimizing control characteristics2 switching frequency Switching between acceleration and deceleration Acceleration/decelerationCurrent stall setting Stall prevention level Protection functionsExternal trip stop by means of a terminal Emergency stop by means of the operation panel ①Press the Stop key Gqhh will blinkOver-torque alarm    Undervoltage trip Under voltage trip selection FM/OUT terminal selection 1 12 OT over-torque detectionSetting methods Canceling the settingOperation panel parameters Analog input disconnection detection Communication function common serial Changing the standard monitoring item Selection of monitor display selection 16.1 Using RS232C/RS485 conversion units Setting up the communications functionData transmission specifications Communications parameters Common serial optionsFree notes Free notesSetting the operation frequency Variety of operationRSS4 Setting the operation mode Status monitor mode Setting procedure eg. operation at 60HzMonitoring the operation status MON Display of trip information ⇔ Taking measures to satisfy the CE / UL / CSA Compliance with CE MarkingAbstract EMC directive【Ex. Countermeasure main circuit wiring】 Compliance with EMC directive Model, noise filter insideModels without EMI filters EMFA2006ZEMFA2015Z EMFAS2011Z【Operating with external signals】【Accessories for countermeasure】【Apply if needed】Compliance with Installation Compliance with UL Standard and CSA StandardCompliance with Low voltage directive Compliance with ConnectionCompliance with Peripheral devices Motor thermal protectionAIC CC/JSelection of wiring materials and devices Peripheral devicesSelection of wiring devices Installation of a magnetic contactor Installation of an overload relayMagnetic contactor in the primary circuit Magnetic contactor in the secondary circuitTable of parameters and data 11.1 User parameters11.2 Basic parameters NN－WNVJT QNOUT NNWNExtended parameters Input/output parametersLOW Frequency parameters NN-WNOperation mode parameters Torque boost parametersAcceleration/deceleration time parameters Factory setting parameter Operation panel parametersCommunication parameters Default settings by inverter rating Table of input terminal functions +SS1+AD2 +SS2+AD2+SS3+AD2 +SS4+AD2Table of output terminal functions Order of precedence of combined functions Specifications Models and their standard specificationsStandard specifications Self-cooling Forced LED External dimensions/weights External dimensions/weightsExternal dimensions Trip causes/warnings and remedies CEE QERFGE QER GRJ GRJ CPU QHHOqhh TVTUvqr UQUK Restoring the inverter from a trip If the motor does not run while no trip message is displayed YESHow to determine the causes of other problems Inspection and maintenance Regular inspectionCheck points Periodical inspection Check itemsReplacement of expendable parts Standard replacement cycles of principal partsMaking a call for servicing Keeping the inverter in storageWarranty Disposal of the inverter Toshiba