Manuals / Toshiba / Marine Equipment / Marine Battery

Toshiba Single-phase 200V class 0.2 to 2.2kW, Single-phase 100V class 0.1 to 0.75kW Resistor

Models: Single-phase 100V class 0.1 to 0.75kW Three-phase 200V class 0.1 to 2.2kW Single-phase 200V class 0.2 to 2.2kW

1 144

Download 144 pages 31.84 Kb

Page 24

Image 24

E6581090

•Do not install in any location of high temperature, high humidity, moisture condensation and freezing and avoid locations where there is exposure to water and/or where there may be large amounts

1of dust, metallic fragments and oilmist.

•Do not install in any location where corrosive gases or grinding fluids are present.

•Operate in areas where ambient temperature ranges from -10°C to 50°C. However, when installing the inverter where the ambient temperature will rise above 40°C, detach the caution label on the top surface.

5cm

5cm

5cm

Measurement position

Measurement position

Note: The inverter is a heat-emitting body. Make sure to provide proper space and ventilation

when installing in the cabinet. When installing the inverter in a cabinet, you are recommended to detach the caution label even if the temperature in the cabinet is below 40°C.

•Do not install in any location that is subject to large amounts of vibration.

•If the VF-nC1 Inverter is installed near any of the equipment listed below, provide measures to insure against errors in operation.

Solenoids:	Attach surge suppressor on coil.
Brakes:	Attach surge suppressor on coil.

Magnetic contactors: Attach surge suppressor on coil.

Fluorescent lights:	Attach surge suppressor on coil.
Resistors:	Place far away from VF-nC1
	Inverter.

Resistor

A-14

Image 24

Toshiba Single-phase 200V class 0.2 to 2.2kW, Single-phase 100V class 0.1 to 0.75kW instruction manual Resistor

Contents

Industrial Inverter How to set a setup parameter ENT Safety precautions Limits in purpose General operation Transportation ‚ Installation Wiring Operations When retry function is selected inverter Attach caution labels ― Contents ― 10.1 Contents of the product code Read firstCheck purchased product Name and function of each part Operation keypad panel Front panel Self-up terminal block VFNC1-2001P～2007P VFNC1-2015P～2022P VFNC1S-1007P VFNC1S-2015P～2022P Control circuit terminal block Same type of terminal board is provided for all models Motors Inverters Disposal What to do about leak currentLeakage current from the inverter main unit Effects of leakage current across ground Affects of leakage current across lines Remedies Installation Installation environment Resistor How to install Installation location VFNC1S VFNC1 Installing more than one unit in a cabinet Connection Control and main power supply WiringStandard connections Preventing radio noise Standard connection diagram VF-nC1 When using V1/S3 terminal as a logic input terminal H DC reactor ＊ DCL option P0 ＊4 DC reactor＊5 Power supply and motor connections Description of terminalsMain circuit terminals Connections with peripheral equipment Control circuit terminals sink logic common CC VI/S3 Sink logic negative common/source logic positive common OUTFLA FLB Switching the input terminal logic between sink and source Simple operation Setting Simple operation of the VF-nC1Run / stop Frequency RUN Motor starts Motor stops slowdown stop Short F and CC terminals run forward Setting the frequency using the operation panel Hoqf Setting the frequency using external potentiometer Setting the frequency by serial communications Hoqf Setting the frequency using input voltageSetting the frequency using current input 4-20mA Basic VF-nC1 operations How to set parameters Setup parameters How to set a setup parameter KP KV How to set the basic parameters Steps in key entry for basic parameters How to set extended parameters Steps in key entry for extended parameters CWH GPF HTH Press the Enter key to display the setting of the parameter ITW CEE Parameters that cannot be changed while running Returning all parameters to standard default setting Kpkv Selecting an operation mode Command mode selectionFrequency setting mode selection Settings Meter setting and adjustment Function Adjustment scale with meter adjustment HO parameter Adjusting the meter in inverter stop stateFM/OUT Houn Standard default setting Setting acceleration/deceleration time Selecting forward and reverse runs operation panel onlyHT Forward/reverse selection Operation panel CEE Acceleration time 1 s FGE Deceleration time 1 s Parameter setting Maximum frequencyUpper limit and lower limit frequencies HJ Maximum frequency Hz Selecting control mode Base frequency Base frequency 1 Hz XD Setting the electronic thermal Setting of motor electronic thermal protection level 1 VJTExplanation of terms Using a VF motor motor for use with inverter Inverter over load characteristicsSetting the motor electronic thermal protection level 1 VJT Preset speed operation speeds in 15 steps Setting method Run/stopPreset speed frequency setting Motor 150%-overload time limit H Using other speed commands with preset speed command Eoqf Output signal-related parameters Output terminal settingExtended parameters FM/OUT terminal functions selection Parameter for specifying a frequency OFF Parameters related to terminal function selection Setting of contact input terminal function Connection method Switching between control logics Sink/Source selection Jog run Setting of output terminal functions Setting of switching terminals Basic parameters40MCHG OFF Analog signals for frequency setting Setting frequency command characteristics Adjustment of 0~10Vdc voltage input Adjustment of 4~20mAdc current input 0 voltage input Starting frequency Starting frequency setting Hz Operation frequency DC braking Preset speed operation frequencies 8 to ～ H Preset speed operation frequencies 8 to 15 HzPWM carrier frequency Jump frequency Hz Jump width Hz Trip-less intensification During restart operation, the message  is displayed Start of motor during coasting Motor speed search functionApplication to a crane or hoist Inverter, motor and machine ・QEC ・QEN・GRJQ ・GTT Setting the PI control parameter Performing PI controlExternal connection Types of PI control interfaces Adjusting the PI control gain level Adjusting an analog command voltage Improving torque and speed characteristics Optimizing control characteristics 2 switching frequency Switching between acceleration and deceleration Acceleration/deceleration Current stall setting Stall prevention level Protection functions External trip stop by means of a terminal Emergency stop by means of the operation panel ①Press the Stop key Gqhh will blink Over-torque alarm    Undervoltage trip Under voltage trip selection FM/OUT terminal selection 1 12 OT over-torque detection Setting methods Canceling the settingOperation panel parameters Analog input disconnection detection Communication function common serial Changing the standard monitoring item Selection of monitor display selection 16.1 Using RS232C/RS485 conversion units Setting up the communications functionData transmission specifications Communications parameters Common serial options Free notes Free notes Setting the operation frequency Variety of operation RSS4 Setting the operation mode Status monitor mode Setting procedure eg. operation at 60HzMonitoring the operation status MON Display of trip information ⇔ Taking measures to satisfy the CE / UL / CSA Compliance with CE MarkingAbstract EMC directive 【Ex. Countermeasure main circuit wiring】 Compliance with EMC directive Model, noise filter inside Models without EMI filters EMFA2006ZEMFA2015Z EMFAS2011Z 【Operating with external signals】【Accessories for countermeasure】【Apply if needed】 Compliance with Installation Compliance with UL Standard and CSA StandardCompliance with Low voltage directive Compliance with Connection Compliance with Peripheral devices Motor thermal protectionAIC CC/J Selection of wiring materials and devices Peripheral devices Selection of wiring devices Installation of a magnetic contactor Installation of an overload relayMagnetic contactor in the primary circuit Magnetic contactor in the secondary circuit Table of parameters and data 11.1 User parameters11.2 Basic parameters NN－WN VJT QNOUT NNWN Extended parameters Input/output parametersLOW Frequency parameters NN-WN Operation mode parameters Torque boost parameters Acceleration/deceleration time parameters Factory setting parameter Operation panel parametersCommunication parameters Default settings by inverter rating Table of input terminal functions +SS1+AD2 +SS2+AD2+SS3+AD2 +SS4+AD2 Table of output terminal functions Order of precedence of combined functions Specifications Models and their standard specificationsStandard specifications Self-cooling Forced LED External dimensions/weights External dimensions/weightsExternal dimensions Trip causes/warnings and remedies CEE QERFGE QER GRJ GRJ CPU QHHOqhh TVT Uvqr UQUK Restoring the inverter from a trip If the motor does not run while no trip message is displayed YES How to determine the causes of other problems Inspection and maintenance Regular inspectionCheck points Periodical inspection Check items Replacement of expendable parts Standard replacement cycles of principal parts Making a call for servicing Keeping the inverter in storage Warranty Disposal of the inverter Toshiba