Precaution | A&D PD4000243 specs

2.1. Precaution

Befor any use, confirm the following articles for the safty operation.

Grounding the indicator

Ground the indicator certainly. The earth terminal is the rear panel.

Separate this earth line from other ground line like a motor, inverter or a power source. Unless the indicator is grounded, it may cause to receive an electric shock, be happen operation error or catch fire

Use adaptable power cord

Confirm the AC voltage and current of the power cord. If the voltage range of cord is lower than power line voltage, it may cause of a leak or catching fire. Use compression terminals to connect the power cord to the terminal of the rear panel.

Fuse

The fuse is installed to prevent the indicator from catching fire.

The indicator is equipped many safety circuits. Therefore, the fuse is not broken in normal operation. If the fuse is broken, do not replace the fuse and contact your local or A&D dealer. This trouble may cause of an electric discharge of thunder.

Splashing water

The indicator is not water-resistant. When the indicator is mounted to panel with accessory rubber, the front panel is equivalent to IP-65.

Flammability gas

Do not install the indicator in any flammable gas.

Radiation of the indicator

Space out instruments to radiate heat sufficiently.

Removing the cover

Remove the power cord terminals in the side of the power source before removing the cover to avoid receiving an electric shock.

Do not touch the internal circuit within 10 seconds after turning off the indicator because of receiving an electric shock.

Page 6

AD-4402

Image 8

A&D PD4000243 manual Precaution

Contents

Multi Function Weighing Indicator Page Contents AD-4402 Remote Operation 102 Function List 103 10.1.1 Operation Keys Compliance with European Directive ComplianceCompliance with FCC rules Outline and Features Precaution Front Panel Keys Symbols Alphanumeric keys NET Rear Panel AC85V Installation Mounting Indicator Adaptable Compression Terminal Parts Connecting Loadcell CableLoadcell Output Adjustment for Zero Calibration Zero Point Verifying Loadcell Output and Input Sensitivity Verification Example Wiring Power Cord Installing Options Standby Mode Basic OperationKey Operation Examples Cursor Operation Way of Entering a Correction Mode Way of Calling a CodeCase of a Material Code Case of a Recipe Code Way of Entering Menu Status Chart Mode map Calibration Common Calibration ItemsItems for the Actual Load Calibration Items for Digital Span Actual Load Calibration using Mass ESC key Digital Span Calibration without Mass Gravity Acceleration Correction Gravity Acceleration Reference Calibration Error CERR1 Applications Hopper Scale with Material CodeDefinition of Material Code Recalling Material Code Editing Principle Parameters of Material Code Referring next Material Code Editing Full Parameters of Material Code Edit Material Code Search Material Code Delete Material CodeExample of Deleting Total Value Copy Material Code Tare of Material Code Simple Hopper Scale with Recipe Code Definition of Recipe Code Formal Function Recalling a Recipe Code Using a Recipe CodeConstruction of Recipe Code Arranging Material Code in Recipe Code Editing Full Parameters of Recipe CodeEdit Name of Recipe Code Search of Recipe Code Copy of Recipe Code Setup System Design of Hopper ScaleOperation and I/O Design Design Example Weighing Mode Contents of Batch Weighing Mode Normal Batching Batch Weighing ModeLoss-in-weight Selection of Normal Batching or Loss-in-weight External Selection Normal batch weighing or Loss-in weightSelection of Batch Weighing Advise Sequential Weighing Mode Normal Batching of Sequential WeighingForecast Control Function Concerning Parameters of the Function Changing the timing of comparison Drawing Normal Batching of Sequential Weighing Loss-in Weight of Sequential Mode Drawing Loss-in Weight of Sequential Weighing Compensation Sequence Drawing Compensation Sequential Entrance Sequence Drawing Entrance Sequence Discharge Sequence Drawing Discharge Sequence Plain Recipe Sequence Weighing a single material code during a recipe sequence Drawing Plain Recipe Sequence Case 2 Gate Control with Supplying Mat Selection Automatic Selection of Supplying MatCase 1 Direct Gate Control Nozzle Control Sequence vacuum cleaner Mixture Sequence Material Safety Check Function Pause and Emergency Stop Restart Sequences from Pause Automatic Free Fall Compensation Real Time Free Fall Compensation Customer Programmed Control Comparison Output Normal Batching of Comparison Function Arbitrary width can be set Drawing Normal Batching of Comparison Function Loss-in Weight of Comparison Function Nn terminal number of the I/O Batch start delay timer Zero Tracking Function Other FunctionsRe-Zero Operation Customizing Function Key Key Design Preset Tare Fixed Tare FunctionTare Items to append to sub-display Customizing Sub DisplayRow and Colum Address Graphic Display Clearing Deleting Accumulation Data Accumulation OperationUndoing Accumulation Operation Error Message and Alarm Kind of Alarm and Error Dispaly can not be zeroed by zero compensation Graphic Status Indicator Memory Backup Interface Control I/O FunctionInterface circuit Input terminal Timing Chart Function assigned to terminals Built-in RS-485 Interface ConnectionWay of Use and Note Terminals Settings of Parameters System Connections Stream Mode Communication Modes General Data Format Weighing data Broadcast Address 5. A&D Data FormatAddress Write Commands Command ListMonitor Commands Control Commands Cetl Response Error Code Ascii Code for AD-4402 Built-in Current Loop Output Communication Modes Connection Data FormatBCD Output of Option, OP-01 Terminals AD-4402 Timing Chart When normal output 01f- 3 without 5 is used Relay Output of Option, OP-02 Terminal List RS-422/485 Interface of Option, OP-03 RS-485 4 Wire Connections RS-422 Connections RS-485 2 Wire Connections Settings of Parameters RS-232C Interface of Option, OP-04 Parallel I/O of Option, OP-05 Analog Output of Option, OP-07 Maintenance Monitor ModeBasic Operation Monitoring Control I/O Function Monitoring Built-in Current Loop Output Monitoring A/D ConverterMonitoring BCD Output of OP-01 Monitoring Relay Output of OP-02 Monitoring RS-422/485 Interface of OP-03 Monitoring RS-232C Interface of OP-04Monitoring Parallel I/O of OP-05 Monitoring Analog Output of OP-07 Test Mode Testing Control I/O FunctionTesting Built-in RS-485 Interface Testing Built-in Current Loop Output Testing A/D Converter Testing BCD Output of OP-01Testing Relay Output of OP-02 Testing RS-422/485 Interface of OP-03 Testing Analog Output of OP-07 Testing RS-232C Interface of OP-04Testing Parallel I/O of OP-05 Kinds of intialization mode Initializing Parameters Prucedure To enter intialization Entering to the Remote Operation Mode Remote Operation Example of an item Function ListOperation Keys Outline of the Function List Options Parameter Settings Referring Parameters Category address Function Function setting General Weighing Parameter List Category 5ub f Key operation Category address Function Function setting General Others Clear all total data for material codes Category Category address Function Function setting Sequence Basic Category address Function Function setting Sequence Control Select a action at batch finish Category address Function Function setting Sequence Timer Second Digit Category address Function Function setting Sequence Setpoint Category address Function Function setting Sequence Total Category address Function Function setting Sequence Safety BCD Terminal name Default choices Lt No Discharge Open the dscharge gate Alarm 0utf-11 Output terminal Category address Function Function setting Serial RS-485 Category Range OP-01 Option BCD Output OP-02 Option Output Relay Output Slot n slot number Category Range Address symbol OP-05 Option Parallel input / output Plural terminals and keys OP-07 Option Analog Output Specifications GeneralAnalog to Digital Unit Display Code data Connectors and interfacesWeighing Standard I/O terminal Standard RS-485 interfaceCurrent loop BCD Output of Option Dimensions Accessories References Abbreviation Ascii Code for AD-4402 Index Shift key 113 Water-resistant panel ﾍﾟｰｼﾞ Tqv wxyww+yxr yus