10.4. Parameter List

Category address: [Function] - [Function setting] - [General] - [Weighing]

Category

 

 

 

 

Range

 

address

Name

 

Descriptions

and

Default

symbol

 

 

 

 

choices

 

genf- 1

Display refresh rate

1: five times per second

1 to 2

2

 

 

2: ten times per second

 

 

 

 

0: Not used

Select 3dB band for two

 

 

 

 

1: 11 Hz

low pass filters.

 

 

 

 

2: 8.0 Hz

 

 

0 to 99

 

 

 

3: 5.6 Hz

A/D converter

 

 

 

Digital filter

4: 4.0 Hz

 

4 8

genf- 2

 

 

 

 

 

 

5: 2.8 Hz

 

 

 

 

 

First filter

 

 

 

 

6: 2.0 Hz

 

 

 

 

7: 1.4 Hz

 

 

 

 

 

 

 

 

 

 

 

 

8: 1.0 Hz

Second filter

 

 

 

 

9: 0.7 Hz

 

 

 

 

genf- 3

Sampling

Use to decrease the cut-off frequency of

0 to 10

1

 

freqeuncy divider

digital filter.

 

 

 

 

genf- 4

Stability detection

The detection condition concerning

0.0 to

1.0 s

time

satblility.

 

 

9.9 s

 

 

 

 

genf- 5

Stability detection

0.0 : stable at anytime.

0.0 to

2.0 d

band width

 

 

 

9.9 d

 

 

 

 

 

 

 

The range to zero gross display.

 

 

genf- 6

Zero Range

Center of range is zero calibration.

0 to 30 %

5 %

 

 

Unit: percentage of weighing capacity.

 

 

genf- 7

Zero tracking time

The function automatically traces the

0.0 to

0.0 s

weighing deviation at nearly zero

9.9 s

 

 

 

genf- 8

Zero tracking band

point and keeps zero display of gross

0.0 to

0.0 d

width

display.

 

 

9.9 d

 

 

 

 

 

Tare and zero

When unstable weghinng, whether zero

 

 

 

or tare command is used.

 

 

genf- 9

compensation at

0 to 1

1

0 :Disabled

 

 

 

unstable status

 

 

 

 

 

1 :Enabled

 

 

 

 

 

 

 

 

 

 

 

 

When negative weghinng, whether tare

 

 

genf-10

Tare at negative

command is used.

0 to 1

1

GROSS weight

0 :Prohibition to tare.

 

 

 

 

 

1 :Permission to tare.

 

 

 

 

Preset tare of material code

 

 

genf-11

Preset tare

0 :Not used

 

 

0 to 1

1

 

 

1 :Use

 

 

 

 

 

 

1: If tare value of material code is zero,

 

 

genf-12

Preset tare =0

the last tare value is used.

1 to 2

1

choice

2: If tare value of material code is zero,

 

 

 

 

 

Tare is set to zero.

 

 

 

 

 

 

 

 

 

Page 106

AD-4402

Page 108
Image 108
A&D PD4000243 manual Parameter List, Category address Function Function setting General Weighing