Cisco Systems 15501 Communication Connections

2-6

Cisco ONS 15501 User Guide

78-14134-02, Release 2.0

Chapter2 Installing the Cisco ONS 15501

Communication Conn ections

Figure2-3 Connecting the Cisco ONS 15501 to a DC Power Source

Communication Connections

The Cisco ONS 15501 communic ates in three ways:

•SNMP (through Ethernet)

•alarm contacts (through RJ-45 connector)

•console port (through RS-232)

See AppendixC, “Connector Pinouts”for the wiring layouts of the RJ-45 and RS-232 connectors.

See the “Configuring Local Serial Communication” section on page 3-1 for detailed information about

the RS-232 console port.

1Primary DC power connections 3Redundant DC power connections

2Tapped frame grounding holes

-48V RET -48V RET

68380

Redundant DC power

1 3

2

Contents

Main Cisco ONS 15501 User Guide Page Page Page Page Page Page Page Preface Audience Organization x Conventions Notes use the following conventions: publication. Cautions use the foll owing conventions: cause harm to the equipment. Warnings use the following conventions: xi Related Documentation Obtaining Documentation Cisco.com Documentation CD-ROM Ordering Documentation Obtaining Technical Assistance Cisco.com Technical Assistance Center Cisco TAC Website Cisco TAC Escalation Ce nter Obtaining Additional Publications and Information Page Product Overview Product Description Optical Specifications Key Features Constant Gain Flatness Optimized Automatic Gain Control Variable Gain Transient Suppression Low Noise Figure High Maximum Output Power Network Management Cisco ONS 15501 Applications Point-to-Point Topologies Ring Topologies Adding or Dropping Wavelengths Adjusting to Span Loss Changes 4 1 8 9 11 112 6 Cisco ONS 15501 Front Panel 53 7 10 Page Cisco ONS 15501 LED Alarm Definitions Page Installing the Cisco ONS 15501 Creating a Site Log Required Tools and Parts Installation Checklist Rack-Mounting the Chassis Optical Connection DC Power Connection 1 2 3 Grounding the Chassis Connecting the Power Communication Connections 2 1 3 Setting Up Alarm Contacts Installation Commands Introductory Commands Review and Operational Commands Page Configuring the Cisco ONS 15501 Configuring Local Serial Communication Setting Up the Software Configuring a Basic System Monitoring Alarms and Traps Upgrading the Flash Image Configuring Remote Communication Configuring for Telnet Configuring for SNMP Alarm Contact Closures Page Page Command Reference add-snmp-com add-snmp-mgr alarm boot-bank copyright del-snmp-com del-snmp-mgr ethmode gain gainmean gaintrig get-snmp-com get-snmp-mgr help 4-16 The following example shows how to access a list of available master password c ommands. hide-trap host-config inpwr inpwrmean inpwrtrig ip-config logout neighbor-in Page neighbor-out Page ntp ntp-ip optoutpwr outsigpwr outsigpwrmean outsigpwrtrig ping ps1 ps2 reboot resetmeantrig restore setgainmean setgaintrig setinpwrmean setinpwrtrig set-master-pwd setoutsigpwrmean setoutsigpwrtrig settempmean settemptrig set-time Page set-user-pwd show-trap status sw-download Page sys-info temp tempmean temptrig time timeout timezone Troubleshooting Basic Diagnostic Procedures Isolating the Problem Reading the Front Panel LEDs Password Recovery Technical Support A Cisco ONS 15501 Alarms Page Page Page B Technical Specifications Cisco ONS 15501 Optical Specifications Cisco ONS 15501 Electrical Specifications Cisco ONS 15501 Mechanical Specifications Cisco ONS 15501 DC Input Power Requirements Page C-2 D Time Zone Codes Page E Translated Safety Warnings Wrist Strap Warning Restricted Area Warning E-2 Qualified Personnel Warning E-3 DC Protection E-4 Disconnect Device Warning E-5 E-6 Laser Radiation Warning INDEX A B C D E F G I L M N O P R S T V