Ware Switcher, Message Log | ClearOne comm XAP 400 specs

Operation ~ Utilities

81

G-Ware Switcher

G-Ware Switcher allows you to alternate between different G-Ware software versions that are installed on the same PC. Prior to this release, the older version of G-Ware had to be removed before the new version could be installed. If you want to reinstall previous versions, you must install them in different directories or G-Ware Switcher will not work properly. Install the current version last.

To use G-Ware Switcher

1.Launch G-Ware Switcher from the Windows Start menu by selecting Programs, ClearOne G-Ware, and then G-Ware Switcher.

The G-Ware Switcher Utility Window opens. G-Ware Switcher automatically searches the PC for G-Ware software versions and displays them in the window.

Figure 5.16. G-Ware Switcher

2.Select the G-Ware version you want to use.

3.If the selected G-Ware version is older than any other version of G-Ware on the PC, click Re-Register/Make Shortcuts.

4.Click Run. The selected G-Ware version launches. Click Refresh to initiate a new search for G-Ware versions.

Message Log

The Message Log displays messages indicating successful or unsuccessful site connection and all errors. This information is displayed automatically. To open the Message Log, click the Message Log toolbar button or select Message Log from the Tools menu.

Figure 5.18. Message Log window

Figure 5.17.

Message Log button

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 88

ClearOne comm XAP 400 operation manual Message Log, To use G-Ware Switcher

Contents

Audio Products XAP 400 Audio Conferencing System XAP 400 Audio Conferencing System XAP 400 Installation ClearOne Part No July 2002 Rev Table of Contents Iii Advanced Configuration System Configuration Control Operation Appendices Features Introduction Professional Services Group Sales and Customer ServiceTechnical Support ClearOne Communications EuMEA GmbH Product registration Product returns Unpacking Controls and Connections Front panel Rear panel Introduction ~ Controls and Connections Networking Expansion bus Power Operational RequirementsTelephone line Introduction ~ Operational Requirements Equipment placement Environmental Installation Hardware Setup Installation ~ Hardware Setup To connect the unit Installation ~ Networking Units Networking UnitsExpansion bus connections To create an expansion bus network Mixer mode To select a mixer modeDevice IDs To assign device IDs Installation ~ LCD Programming LCD ProgrammingLCD menu tree Pressing ESC at the top of the tree does nothing Select Preset To adjust a parameterSystem menu RS-232 menu Installation ~ LCD Programming Flow Control hardware Enable ModemClear Password Meter menu Outputs ProcessingTelco RX Telco TX Default Meter Inputs menuOutputs menu Mute Matrix Technical Services Group ~ 1-800-283-5936 USA ~ Ware Requirements WindowsWindows ME Windows NT To install G-Ware Installing G-WareCreating floppy disk copies Site Setup Control usingCreating a new site To create a new site Adding a XAP To auto-detect unitsTo manually add units File menu Configuring Unit Properties To configure Unit Properties 14. Unit Properties Security tab Ware Screens Flow Screen Safety Mute Copying and pasting settingsStatus bar System Configuration ~ G-Ware Screens Matrix Screen Audio Routing Expansion bus O-Z routingProcess A-D routing Cross point attenuation System Configuration ~ Audio Routing Matrix report Inputs and Outputs Inputs Target Pwr Phantom PowerPA Adapt and AEC Reference To create a virtual reference Click Close to exit the window Filters Non-linear Processing NLPMeters Active Filter Type 33. Inputs 1-4 Filters window To configure filters Table View PA Adaptive Mode GateActivation Chairman Override Gate Ratio Hold TimeOff Attenuation Ambient Level 39. Virtual Reference window Gating Group Select To configure gating group settingsTo assign a gating group Click the Gating Group label to change the group names Min/Max limits Meters AGC 48. Gain meters Outputs NOM Optimizing output gain structure From Expansion Bus O-Z Expansion BusesTo Expansion Bus O-Z Processing A-D ProcessingCmprs compressor Post Compressor Gain GroupThreshold Ratio AttackRelease Input meter Phase BypassAdd Filter Remove Filter Delay Changes you make in the distance and temperature fields 58. Process Gain adjust and meter Optimizing process gain structure Telco Setup To configure telco settingsClick the Telco Config button on the XAP 400 Flow Screen Have System Configuration ~ Telco Setup Telco Transmit and Receive System Configuration ~ Telco Transmit and ReceiveTelco Transmit Green button light illuminates when ALC is enabled From 6dB to 15dB. Default is 6dBSignal-to-noise ratio without clipping the signal Telco Receive Creating Presets PresetsOverview Preset password is set in the Unit Properties window see Preset Configuration paneMatrix Screen Advanced Configuration ~ Presets To enable Acoustic Echo Assigning virtual references to the preset To create a preset Storage space Running presets Running multiple presets simultaneouslyTo run a preset using G-Ware To run a preset using front panel control All presets are ready to run again Room combining example Four macros one for each configuration are set up as follows Macros To create a macro using Macro RecorderCreating macros To create a macro using Macro Editor 16 Macro Name window To add or insert a command line Editing macrosTo edit a macro To delete a macro To run a macro using front panel control To run a macro using the Select panel or GpioUse the macro command. See Control for more details Running macros Using the XAP To answer a callTo make and disconnect a call Audible Ring Indication Using the Dial Interface To dial multiple numbersTo mute Telephone line Operation ~ Using the Dial Interface Touch-tone dialing Signal Generator UtilitiesOperation~ Utilities To use pink or white noise Document Compare Utility Operation ~ Utilities To compare site files Open window Copying settings Print Preview window Copy and paste settings Print Reports To upgrade firmware GFirm Firmware UtilityToolbar Button 15. Selecting baud rate To use G-Ware Switcher Ware SwitcherMessage Log Gate View Monitoring ViewsMeter Views To configure Meter Views Telco metersOperation~ Monitoring Views Telco Echo Return Loss Terl Telco Echo Return Loss Enhancement Terle Total Telco Echo ReductionTransmit Input Transmit Output Gpio Builder To program control/status pinsControl/Status a Remote Builder XAP IR Remote ClearOne Control Panels Select IR Remote default from the Select Remote Type listControl ~ Remote Builder To program the XAP IR Remote To program the Volume panel One IR remote can be Control ~ Remote Builder To program the Select panel Serial commands Remote Modem AccessRS-232 Port Command strings To create a command stringTo run a command string Control ~ RS-232 Port Technical Services Group ~ 1-800-283-5936 USA ~ Appendix a Specifications Appendices Appendices ~ Appendix a Specifications Appendix B Pinouts RS-232 COM DCE port pinout femaleAppendices ~ Appendix B Pinouts Pin Number Control Control/Status connectors First 16 pins onPin Definable Type Default Description Control/Status a Port Pinout female Preset select status for Pin Preset select bitControl/Status B port pinout RS-485 Remote Panel a and B connectors Set connector pinoutLine connector pinout Pin Description Appendix C Control Panel Connecting the Control PanelAppendices ~ Appendix C Control Panel 100 Appendices ~ Appendix C Control Panel Appendix D Accessories Appendices ~ Appendix D AccessoriesAccessory ClearOne Part Number 101 Appendix E Serial Commands Command structure102 Conventions Appendices ~ Appendix E Serial Commands 103Groups and channels Type and device IDs Error number Text message Explanation/Solution Meter type definitions Serial command error codes104 Command Function XAP 400 Serial commands105 106 AA Auto-Answer Enable/ Disable Aamb Adaptive Ambient Mode107 Aconn Audible Connect / Disconnect Indication AD Auto-Disconnect Enable/ Disable AEC Acoustic Echo Canceller Enable/Disable108 Aconnlvl Audible Connect/Disconnect Level Agcset Automatic Gain Control Adjust 109AGC Automatic Gain Control Channel See Groups and Channels on 7,I,M,L Value Amblvl Ambient Level Adjust 110ALC Automatic Level Control Baud Baud Rate 111 Chairo Chairman Override ModeCgroup Compressor Group Select Compress Compressor Adjust 112Compsel Compression Select Gain of 3dB Decay Decay Adjust Delay Delay Adjust113 Country Country Selection Delaysel Delay Select Dfltm Default Meter114 Dial Dtmf Dialing Command form Channel 115Did Device ID Dspver DSP Version Filter Filter Adjust 116Dtonelvl Dial Tone Level Name Description Units 117 Filtsel Filter SelectFlow Flow Control Examples FMP First Mic Priority Mode 118FPP Front Panel Passcode Button assignment Gain Gain Adjustment 119Gate Gate Status Channel See Groups and Channels, L, M, P, R, T Value GHOLD- Gate Hold Time Adjust Gmode Gating Mode120 Gover Gating Override Gratio Gate Ratio Adjust 121Greport Gate Report Grpsel Gating Group Select 122 Hook Hook FlashHookd Hook Flash Duration Label Label LMO Last Mic On Mode Lock Preset and Macro Lock123 LFP Lock Front Panel Lockprst Apply the lock to a preset or macro Lockpwd Set preset/macro password124 LVL Level 125 Lvlreport Level ReportLvlrrate Level Report Rate = Toggle Master Expansion Bus Master Mode MAX Maximum Gain Setting126 Macro Macro Execution/Reporting Mdmode Modem Mode MIN Minimum Gain SettingCommand form Device Mdmode Value 127 128 Minmax Minimum and Maximum Gain SettingMinit Modem Initialization String Mline Mic/Line Adjust Mpass Modem PasswordCommand 129 Mtrxlvl Matrix Attenuation Adjustment 130Mtrx Matrix SRC = source Dest = destination Chnl = channel GRP = group NCD Noise Cancellation Depth Ncsel Noise Cancellation Select131 Mute Mute NLP Non-Linear Processing Adjust NOM Number of Open Microphones Mode132 Null Null the line Offa Off Attenuation Mode PAA PA Adaptive ModePP Phantom Power Command Channel Select mic input Value Preset Preset Execution/Reporting 134Prgstring Program String Supported special characters Ramp Ramp Gain Adjustment 135Redial Dial the last number again Name Description Unit Refset Reference channel setup 136Refsel PA/AEC Reference Select Ring Ring Indication 137 Ringer Audible Ring SelectionRingerlvl Audible Ring Level Rxboost Receive Boost Rxbsten Receive Boost Enable 138Rxrd Telco Receive Reduction Serecho Serial Echo Sermode Serial Mode Sftymute Safety muteSiggen Signal Generator 139 Sigtout Signal Generator Time Out Slvl Speech Level Control Enable/Disable140 Speeddial Speed Dialing Tamode Telco Adapt Mode 141Storedial Store a Number as a Speed Dial String String Execution TE Telco Enable 142Terl Telco Echo Return Loss Terle Telco Echo Return Loss Enhancement 143 Tout Time Out SelectUID Unit ID VER Version Appendix F Warranty 144 Appendices ~ Appendix F Warranty 145 146 Appendix G ComplianceFCC Part 15 Compliance FCC Part 68 Compliance IC Compliance 147Appendices ~ Appendix G Compliance 148 Safety Information European ComplianceEC Declaration of Conformity 149 Telecommunications Terminal Equipment Glossary 150Glossary 151 152 153 Ware Software The XAP 400’s setup and configuration software 154 155 156 Required to allow remote modem access 157 Signal Delay Used for 158 159 Index 16033-35 161 Index 162 NOM Frequency response Phase 163 164 165