130, Mtrx Matrix | ClearOne comm XAP 400 specification

130	Appendices ~ Appendix E: Serial Commands

✍

SRC = source DEST = destination CHNL = channel GRP = group

MTRX - Matrix

This command selects/reports the matrix routing of an input to an output. Command form: DEVICE MTRX <SRC CHNL> <SRC GRP> <DEST CHNL>

<DEST GRP> [Value]

Argument details

Name	Description
Device	0–7 or * to select all units
MTRX	Command form
SRC CHNL	See Groups and Channels, page 103
SRC GRP	I, M, P, L, E
DEST CHNL	See Groups and Channels, page 103
DEST GRP	O, P, E
Value	0	= Cross point off
	1	= Cross point on (not valid for mic sources)
	2	= Cross point toggle (not valid for mic sources)
	3	= Non-gated (mic sources only)
	4	= Gated (mic sources only)\

Null = Current mode

Example: #77 MTRX 1 M 4 O 4 On XAP 400 unit 7 (#77), mic (M) channel 1 is routed (MTRX) as gated (4) to output (O) 4.

✍ Values indicate entry range only. Actual internal range of the gain stage is from

-60 to 0 and absolute values will be limited to the internal gain range. Absolute levels below -60 will mute the gain stage.

MTRXLVL - Matrix Attenuation Adjustment

This command selects/reports the matrix level at the cross point. Command form: DEVICE MTRXLVL <SRC CHNL> <SRC GRP>

< DEST CHNL> <DEST GRP> [Value] [A/R]

Argument details

Name	Description	Units
Device	0–7 or * to select all units
MTRXLVL	Command form
SRC CHNL	See Groups and Channels, page 103
SRC GRP	I, M, P, L, E
DEST CHNL	See Groups and Channels, page 103
DEST GRP	O, P, E
Value	-99.99 to 99.99	dB
	Null = Current mode
A/R	A = Absolute
	R = Relative, Null = Relative

Example: #70 MTRXLVL 1 M 4 O -6 On XAP 400 unit 0 (#70), cross point attenuation (MTRXLVL) at the point of mic (M) 1 and output (O) 4 is -6dB.

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 137

ClearOne comm XAP 400 operation manual 130, Mtrx Matrix, Mtrxlvl Matrix Attenuation Adjustment

Contents

Audio Products XAP 400 Audio Conferencing System XAP 400 Audio Conferencing System XAP 400 Installation ClearOne Part No July 2002 Rev Iii Table of Contents System Configuration Advanced Configuration Operation Control Appendices Introduction Features Sales and Customer Service Professional Services GroupTechnical Support ClearOne Communications EuMEA GmbH Unpacking Product registration Product returns Front panel Controls and Connections Introduction ~ Controls and Connections Rear panel Expansion bus Networking Operational Requirements PowerTelephone line Introduction ~ Operational Requirements Environmental Equipment placement Hardware Setup Installation To connect the unit Installation ~ Hardware Setup Networking Units Installation ~ Networking UnitsExpansion bus connections To create an expansion bus network To select a mixer mode Mixer modeDevice IDs To assign device IDs LCD Programming Installation ~ LCD ProgrammingLCD menu tree Pressing ESC at the top of the tree does nothing System menu To adjust a parameterSelect Preset RS-232 menu Enable Modem Installation ~ LCD Programming Flow Control hardwareClear Password Meter menu Processing OutputsTelco RX Telco TX Inputs menu Default MeterOutputs menu Mute Matrix Technical Services Group ~ 1-800-283-5936 USA ~ Windows Ware RequirementsWindows ME Windows NT Creating floppy disk copies Installing G-WareTo install G-Ware Control using Site SetupCreating a new site To create a new site To auto-detect units Adding a XAPTo manually add units File menu To configure Unit Properties Configuring Unit Properties 14. Unit Properties Security tab Flow Screen Ware Screens Status bar Copying and pasting settingsSafety Mute Matrix Screen System Configuration ~ G-Ware Screens Expansion bus O-Z routing Audio RoutingProcess A-D routing Cross point attenuation Matrix report System Configuration ~ Audio Routing Inputs Inputs and Outputs PA Adapt and AEC Reference Pwr Phantom PowerTarget Click Close to exit the window To create a virtual reference Non-linear Processing NLP FiltersMeters Active Filter 33. Inputs 1-4 Filters window Type Table View To configure filters Gate PA Adaptive ModeActivation Chairman Override Hold Time Gate RatioOff Attenuation Ambient Level 39. Virtual Reference window To assign a gating group To configure gating group settingsGating Group Select Min/Max limits Click the Gating Group label to change the group names Meters AGC 48. Gain meters NOM Outputs Optimizing output gain structure To Expansion Bus O-Z Expansion BusesFrom Expansion Bus O-Z Cmprs compressor ProcessingProcessing A-D Threshold GroupPost Compressor Gain Attack RatioRelease Input meter Bypass PhaseAdd Filter Remove Filter Changes you make in the distance and temperature fields Delay Optimizing process gain structure 58. Process Gain adjust and meter To configure telco settings Telco SetupClick the Telco Config button on the XAP 400 Flow Screen Have System Configuration ~ Telco Setup Telco Transmit System Configuration ~ Telco Transmit and ReceiveTelco Transmit and Receive From 6dB to 15dB. Default is 6dB Green button light illuminates when ALC is enabledSignal-to-noise ratio without clipping the signal Telco Receive Overview PresetsCreating Presets Matrix Screen Preset Configuration panePreset password is set in the Unit Properties window see Advanced Configuration ~ Presets Assigning virtual references to the preset To enable Acoustic Echo Storage space To create a preset Running multiple presets simultaneously Running presetsTo run a preset using G-Ware To run a preset using front panel control Room combining example All presets are ready to run again Four macros one for each configuration are set up as follows Creating macros To create a macro using Macro RecorderMacros 16 Macro Name window To create a macro using Macro Editor Editing macros To add or insert a command lineTo edit a macro To delete a macro To run a macro using the Select panel or Gpio To run a macro using front panel controlUse the macro command. See Control for more details Running macros To answer a call Using the XAPTo make and disconnect a call Audible Ring Indication To dial multiple numbers Using the Dial InterfaceTo mute Telephone line Touch-tone dialing Operation ~ Using the Dial Interface Utilities Signal GeneratorOperation~ Utilities To use pink or white noise Operation ~ Utilities Document Compare Utility Open window To compare site files Print Preview window Copying settings Print Reports Copy and paste settings GFirm Firmware Utility To upgrade firmwareToolbar Button 15. Selecting baud rate Message Log Ware SwitcherTo use G-Ware Switcher Meter Views Monitoring ViewsGate View Telco meters To configure Meter ViewsOperation~ Monitoring Views Telco Echo Return Loss Terl Total Telco Echo Reduction Telco Echo Return Loss Enhancement TerleTransmit Input Transmit Output Control/Status a To program control/status pinsGpio Builder XAP IR Remote Remote Builder Control ~ Remote Builder To program the XAP IR Remote Select IR Remote default from the Select Remote Type listClearOne Control Panels One IR remote can be To program the Volume panel To program the Select panel Control ~ Remote Builder RS-232 Port Remote Modem AccessSerial commands To create a command string Command stringsTo run a command string Control ~ RS-232 Port Technical Services Group ~ 1-800-283-5936 USA ~ Appendices Appendix a Specifications Appendices ~ Appendix a Specifications RS-232 COM DCE port pinout female Appendix B PinoutsAppendices ~ Appendix B Pinouts Pin Number Control First 16 pins on Control/Status connectorsPin Definable Type Default Description Control/Status a Port Pinout female Control/Status B port pinout Preset select bitPreset select status for Pin Set connector pinout RS-485 Remote Panel a and B connectorsLine connector pinout Pin Description Appendices ~ Appendix C Control Panel Connecting the Control PanelAppendix C Control Panel Appendices ~ Appendix C Control Panel 100 Appendices ~ Appendix D Accessories Appendix D AccessoriesAccessory ClearOne Part Number 101 Command structure Appendix E Serial Commands102 Conventions 103 Appendices ~ Appendix E Serial CommandsGroups and channels Type and device IDs 104 Meter type definitions Serial command error codesError number Text message Explanation/Solution 105 XAP 400 Serial commandsCommand Function 106 Aamb Adaptive Ambient Mode AA Auto-Answer Enable/ Disable107 Aconn Audible Connect / Disconnect Indication AEC Acoustic Echo Canceller Enable/Disable AD Auto-Disconnect Enable/ Disable108 Aconnlvl Audible Connect/Disconnect Level 109 Agcset Automatic Gain Control AdjustAGC Automatic Gain Control Channel See Groups and Channels on 7,I,M,L Value 110 Amblvl Ambient Level AdjustALC Automatic Level Control Baud Baud Rate Cgroup Compressor Group Select Chairo Chairman Override Mode111 112 Compress Compressor AdjustCompsel Compression Select Gain of 3dB Delay Delay Adjust Decay Decay Adjust113 Country Country Selection Dfltm Default Meter Delaysel Delay Select114 Dial Dtmf Dialing 115 Command form ChannelDid Device ID Dspver DSP Version 116 Filter Filter AdjustDtonelvl Dial Tone Level Name Description Units Filtsel Filter Select 117Flow Flow Control Examples 118 FMP First Mic Priority ModeFPP Front Panel Passcode Button assignment 119 Gain Gain AdjustmentGate Gate Status Channel See Groups and Channels, L, M, P, R, T Value Gmode Gating Mode GHOLD- Gate Hold Time Adjust120 Gover Gating Override 121 Gratio Gate Ratio AdjustGreport Gate Report Grpsel Gating Group Select Hook Hook Flash 122Hookd Hook Flash Duration Label Label Lock Preset and Macro Lock LMO Last Mic On Mode123 LFP Lock Front Panel Lockpwd Set preset/macro password Lockprst Apply the lock to a preset or macro124 LVL Level Lvlreport Level Report 125Lvlrrate Level Report Rate = Toggle MAX Maximum Gain Setting Master Expansion Bus Master Mode126 Macro Macro Execution/Reporting MIN Minimum Gain Setting Mdmode Modem ModeCommand form Device Mdmode Value 127 Minit Modem Initialization String Minmax Minimum and Maximum Gain Setting128 Mpass Modem Password Mline Mic/Line AdjustCommand 129 130 Mtrxlvl Matrix Attenuation AdjustmentMtrx Matrix SRC = source Dest = destination Chnl = channel GRP = group Ncsel Noise Cancellation Select NCD Noise Cancellation Depth131 Mute Mute NOM Number of Open Microphones Mode NLP Non-Linear Processing Adjust132 Null Null the line PAA PA Adaptive Mode Offa Off Attenuation ModePP Phantom Power Command Channel Select mic input Value 134 Preset Preset Execution/ReportingPrgstring Program String Supported special characters 135 Ramp Ramp Gain AdjustmentRedial Dial the last number again Name Description Unit 136 Refset Reference channel setupRefsel PA/AEC Reference Select Ring Ring Indication Ringer Audible Ring Selection 137Ringerlvl Audible Ring Level Rxboost Receive Boost 138 Rxbsten Receive Boost EnableRxrd Telco Receive Reduction Serecho Serial Echo Sftymute Safety mute Sermode Serial ModeSiggen Signal Generator 139 Slvl Speech Level Control Enable/Disable Sigtout Signal Generator Time Out140 Speeddial Speed Dialing 141 Tamode Telco Adapt ModeStoredial Store a Number as a Speed Dial String String Execution 142 TE Telco EnableTerl Telco Echo Return Loss Terle Telco Echo Return Loss Enhancement Tout Time Out Select 143UID Unit ID VER Version 144 Appendix F Warranty 145 Appendices ~ Appendix F Warranty Appendix G Compliance 146FCC Part 15 Compliance FCC Part 68 Compliance Appendices ~ Appendix G Compliance 147IC Compliance EC Declaration of Conformity Safety Information European Compliance148 Telecommunications Terminal Equipment 149 Glossary 150Glossary 151 152 153 154 Ware Software The XAP 400’s setup and configuration software 155 156 157 Required to allow remote modem access 158 Signal Delay Used for 159 33-35 160Index Index 161 NOM 162 163 Frequency response Phase 164 165