Width | Fujitsu DL3750+/3850+ specs

INDEX

Single sheets
ejecting	3–8
Soft (download) fonts	4–1, 5–15
Software, using	2–26, 4–2
Specifications
interface	D–1
paper	B–6
printer	B–1
Supplies	A–1

	T
TEAR OFF button	3–3
Tear-off setup options	5–40
Tearing off forms	3–15
Testing printer
offline	2–13
online	2–26
Top margin, changing	5–20
TOP-MRG	5–20

	U
Unidirectional printing	5–30
Unpacking	2–3
USB interface
cable connection	2–20
optional setting	5–31
specifications	D–11

V
V-ALMNT function	7–10
Vertical character displacement
correcting	7–10

W
WIDTH	5–24
Word length	5–30
WORD-LG	5–30

X
XON/XOFF protocol	D–10

Z
ZEROFNT	5–24

Index

User's Manual

IN-7

Image 253

Fujitsu DL3750+/3850+ manual Width

Contents

Page Page Fujitsu DL3750+/3850+ Important Note to Users Using This Product in High-risk SituationsPage Bescheinigung des Herstellers/Importeurs CE Declaration Energy Saving Trademark Acknowledgement Printer Models and Options About this Manual Organization For Experienced Users Conventions Table of Contents Printing Using Setup Mode Installing Options Appendix a Supplies and Options Appendix F Resident Font Glossary of Terms Control panel Quick Reference Operation Online Offline Required Response Printer Operations Normal Mode Dot matrix printer Features Options Introduction Selecting a Good Setting UPLocation Setting UP Checking items received Removing the shipping restraint cardboard Checking Options and Supplies Installing the cut sheet stand Installing the Cut Sheet Stand Preparing to install the ribbon Installing the Ribbon Cartridge Preparing the ribbon cartridge Installing the ribbon cartridge Setting Up Handling Paper Printing Setup Mode With Your Printer Getting AcquaintedPrinter components front and right Cord Printer components rear Connecting the power cord Offline Testing the PrinterLoading Paper for the Self-Test Loading a sheet of paper Printing the Self-Test Starting the self-test Sample self-test To exit demo mode, turn the printer off Demo pattern To Your Computer Connecting the PrinterSelecting a Parallel Interface Cable Selecting a Serial Interface Cable Selecting a USB Cable Connecting the Interface CableSelecting a LAN cable Opening the shutter Attaching the shutter Removing the shutter Connecting the interface cable For Experienced Users Enter setup mode Initial printout in setup modeTurn the printer on and load a sheet of paper Select an emulation Select the MENU1 function Printing a Sample Exit setup mode to save the emulationOnline Exit MENU1 Setting UP Mode LPT1=COM1 Using MS-DOS to Specify Serial Interface Settings Printer Driver Installing Setting UP Selecting Paper Paper Handling Operations Overview of PaperPrinter levers and buttons Lever/Button Purpose Action Levers and Buttons Used for Paper Handling Adjusting the paper thickness lever Using Single Sheets Paper Thickness Lever SettingsNumber of Copies Setting *2 Including the Original *1 Loading a Single Sheet of Paper Preparing to load a sheet of paper Adjusting the left margin Loading a sheet of paper Ejecting Single Sheets Using ContinuousForms Bad placement Good placementPlacement of continuous forms Positioning the Paper Stack Loading Continuous Forms Paper thickness lever settingPreparing to load continuous forms paper Ajusting the left margin Positioning the tractors Setting the back cover Adjustment procedure Adjusting the Tear OFF position Unloading Continuous Forms Installing the Tractor Unit Tearing off continuous forms Tearing Off Continuous Forms Feeding Load Position AdjustLine Feed/Form Feed Positioning Paper Failure to retract the forms paper will cause paper jams Switching to Single Sheets Tips on Paper Handling General Tips Switching to Continuous FormsMultipart Forms Labels Envelopes Paper Handling Selecting Print Printing Using the Control Panel Using Commercial SoftwarePrinter control panel Selecting MENU1 or MENU2 MENU1 MENU2 MENU1 and MENU2 Settings Starting Printing Starting or Stopping PrintingStopping Printing Resuming from a Paper-Out Continuing printing after supplying paper Printing the remaining lines on a Resuming after an Area Over warning Removing Single Sheets Removing Printed Pages Clearing the Print BufferRemoving Continuous Forms HOW to USE this Chapter Using Setup Mode Entering Setup Mode Initial printout in setup mode Setup Mode Functions Overview of Setup Mode List DefaultSELF-TST HEX-DUMP Load continuous forms paper Enter setup mode Setup Mode ExampleSelect the MENU2 function Summary of setup mode Select the current emulation Exit setup mode, saving the new font and pitchChange the font to Prestige Elite Select the current print quality Points to Remember Printing a List Printer tear-off feature Tear OFF buttonSelected Options Select the List function Printout of factory defaults using List Deciding Which System and printer accessory compatibilityOptions to Change Required Options See the section Changing Configuration Adjustment Options later in thisSee the section Changing Hardware See the section Changing Print Position Using Setup Mode Defaults for that emulation Options are reset to the factoryMENU1 and MENU2 Items and Options MENU1 Options Description MENU2 Items RAM Font TIMLS-N TIMLS-B TIMLS-I DOWNLD#Quality Letter Lpi Lpi double spacing Attrib CHAR-HNone Italics Condnsd Shadow Bold Options Description MENU2 Items MENU1LFT-END ## Colm ## Line TOP-MRG USA LangugeGerman Swedish SLOV-T Languge SlovPolish POLSH-T Italian Languge FrenchSpanish DANISH1 SET CHR-SETItalic Graphic Disable EnableCR-CODE CR only CR & LF OVR-PRT Rghtend Wrap Select the MENU1 or MENU2 function Procedure Exit MENU1 or MENU2 Resetting MENU1 and MENU2 Hardwre Items and Options Changing HardwareOptions Description Items Print buffer Download buffer Only for graphics application 0BYTE option is recommendedWith 128KB selected, the printer Cannot accept any download font Number Options DescriptionData bits Parity bit Stop bits DTR XON/XOFREV-CHL DSR Ignore Select an option for the selected item Select the Hardwre function Changing Print Position Adjustment Options Adjust Adjust Items and Options Cntadjl Graphic *1 Adjust Items and Options Exit the Adjust function Select the Adjust functionSelect an option from 1/6IN to 66/6IN Config Items and Options Configuration OptionsChanging Positioning will fail if the page length Setting does not match the actualPerforation spacing Button CutloadLoadtim Decode Areacnt SetupON-LOAD Offline Tractor CONT-PEEdge Gather SKIP-PR Driver Exit the Config function Select the Config functionSelect an option Exiting and Saving Settings are usedPrint the Function menu Select the Save & END function Resetting Power-On Defaults Resetting DefaultsResetting Factory Defaults Resetting Factory Defaults in MENU1 and MENU2 Select the Default function Using the DiagnosticFunctions Handling Paper Select the SELF-TST function Printing Hex DumpsExamine the self-test Exit the SELF-TST function Print the hex dump Select the HEX-DUMP function Exit the HEX-DUMP function Sample hex dump Checking Vertical Print Alignment V-ALMNT Adjust the vertical print alignment at correspondence speed Adjust the vertical print alignment at letter quality speedAdjust the vertical print alignment at draft speed Select the V-ALMNT function Correct vertical print alignment To exit the V-ALMNT function, you must exit setup modeExit the V-ALMNT function DPL24C Plus Organization Handling Paper Differences in IBM Proprinter XL24E Emulation Differences in Epson ESC/P2 Emulation Online Setup Mode Cleaning MaintenanceCleaning and Vacuuming the Printer Printer interior Flat cable Cleaning the Platen and Exit Rollers Removing the ribbon cartridge Paper thickness lever Preparing the ribbon cartridge Dot mark green Head Replacing the PrintReplacing the print head Maintenance Solving Problems TROUBLE-SHOOTINGPrint Quality Problems Problem Solution Print Quality Problems and Solutions Section Changing MENU1 and MENU2 Using the Diagnostic Functions in ChapterMENU1 and MENU2 Options in Chapter Changing MENU1 and MENU2 Options Paper Handling Problems and Solutions Paper Handling Problems Paper Handling Problems and Solutions Tips for clearing a jammed sheet from the printer Operating Problems and Solutions Operating ProblemsError name Error description Recovery method Area Over LED status Printer Failures Error LED states Light BlinkPrinter Failures Diagnostic Functions Getting Help Installing Options Installing Options Supplies Supplies and OptionsOption Supplies Order Number Supplies and Options Physical Specifications Printer and Paper Specifications Functional Specifications Paper length Command sets emulationsNumber of copies Character sets Performance Specifications Form feed speed Line feed speedRibbon life Certification Print area for single sheets Paper Specifications Print area for continuous forms Type of Paper Number of Parts Thickness Paper Thickness Do not use in high humidity environments Printer and Paper Specifications Command Sets Fujitsu DPL24C Function Command Print Mode ControlPlus DC2 Function Command ESC M Horizontal ControlESC P ESC LF Vertical Control NUL Function Command TabulationFormatting ESC O Character Set Control Font Selection and Downloading Word ProcessingBit Selection of font Bit Print quality = 0 = 1 Function Pitch Point Typeface Bit Font quality selection Initialize Printer Function Command Bit Image GraphicsBar Code Printing Ascii BEL Function Command Miscellaneous Selectable options in setup mode Command Factory Default Settings SHADOW, Bold NONE, ITALICS, CondnsdESC E ESC F ESC G ESC H SET 1, SET2 ESC7 DC3 ENABLE, DisableESC6 SKIP, NO-SKIP ESC N ESC O DC4 IBM Proprinter XL24E Emulation ESC T DC2 ESC B NUL ESC D NUL ESC Q # Function Command Character Set ControlDownloading Select graphics mode in AG mode only ESC * m c 1 c Emulation Epson ESC/P2 Space Backspace Carriage return Set elite pitch ESC D + d Function Command Character Set Control Font Selection and Downloading OCR-B OCR-A Graphics type m graphics ESC * m n 1 n Parallel Interface Interface Information Pin Return Signal Direc Description Pin No Name Tion Compatible ModeACK Slct Pin Return Signal Direc Description Pin NoInprm SLCT-IN Nibble Mode Name Tion Data Transmission Timing RTS Serial Interface Serial Options Cable Wiring DSR Protocol Description Serial ProtocolsXON/XOFF USB Interface Specification Cable LAN InterfaceRXI+ Character Sets 1 DPL24C Plus and IBM XL24E Emulation Character SetsCode Page 437 Character Set Character Sets ESC Italic and GraphicsP2 Emulation Italic Character Set Character ECMA94, ISO8859, ISO-LTN, ISO-TUK, CYRILIC, LATIN-9 National Character Sets ALL Emulations PAGE852/PG852-T Code PAGE855 Code PAGE865 Code Page 865Nordic PAGE866 Code Page 866Cyrillic PAGE860 Code Page 860Portugal POLISH/POLSH-T Polish MAZOWIA/MAZOW-T Mazowian HUNGARY/HUNG-T Hungarian SLOV/SLOV-T Slovenian Character Sets ELOT928 Elot PG-DHN Code Page DHN IBM437 IBM IBM851 IBM Character Sets Macedon Macedonian MIKABG ABY PG-MAC ELOT927 Decgr Greek HBR DEC ISO-TUK PAGE862 HBR OLD LATIN-9 Ruscii Sets DPL24C Plus National CharacterIBM XL24E Emulation French French Italian Italian Sets ESC/P2 Emulation DANISH1/NORWEGN Danish1/Norwegian DANISH2 Danish2DANISH1 Danish1 SPANSH1 Spanish1 Epson ESC/P2 emulation Japan Japanese Italian Italian SPANSH2 Spanish2 Norwegn Norwegian French French DANISH2 Danish2 Korea Korea Legal Legal Resident Fonts ALL Sets and SupportedEmulations Resident font ECMA94 National Name Character set Setup menuPAGE852 PAGE855 Macedon ABG ABY LITHUA2 MIKPG-MAC ELOT927 HBR-DEC OCR-B OCR-A Resident Fonts Nimbus Sans Scalable Courier Scalable Normal Bold ItalicNormal Bold Italic Timeless Scalable Normal Byte Glossary of Terms Cpi Cps Cut sheets Defaults Dot matrix Carriage return CR Centronics interface Column Command setCondensed print Continuous forms Base-16 numbering system also commonly referred to as hex LAN interface Nonresident font Normal modeLetter size Line feed LF Line spacing Lpi Monospacing GL-5 Serial interface Setup mode Unidirectional printing Tractor feedUSB interface GL-8 Index DPL24CPLUS GL-1 Pica SELF-TST ON-LORD Width IN-8 Fujitsu ESPANA, S.A Fujitsu Canada INCFujitsu PHILIPPINES, INC C147-E047-01EN