Display

(Function mode 1)

(Function mode 2)

 

Setting, change

 

 

 

Function

Function

Initialization display

Initialization

Setting contents

 

 

sequence

contents

 

 

No.

name

contents

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

19

F-26

Frequency

LIMIT L

0000.0 Hz

0 Hz

0 to 120.0

The lower limit of the frequency

 

 

 

Frequency

lower limiter

 

 

 

(400) Hz

to be set is set. When the lower

 

 

 

limiter

setting

 

 

 

 

limit is 0, the setting is invalid.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Frequency

LIMIT H

0000.0 Hz

0 Hz

0 to 120.0

The upper limit of the frequency

 

 

 

 

upper

 

 

 

(400) Hz

to be set is set. When the upper

 

 

 

 

limiter

 

 

 

 

limit is 0, the setting is invalid.

 

 

 

 

setting

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

20

F-27

Jump

JUMP F1

0000.0 Hz

0 Hz

0 to 400 Hz

• The section where frequencies

 

 

 

Jump

frequency

 

 

 

 

are to be jumped is set.

 

 

 

frequency

setting (1)

 

 

 

 

• Up to three locations can be

 

 

 

 

 

 

 

 

 

set.

 

 

 

 

 

 

 

 

 

• When the number of locations

 

 

 

 

 

 

 

 

 

is 0, the setting is invalid.

 

 

 

 

Jump

JUMP F2

0000.0 Hz

0 Hz

0 to 400 Hz

 

 

 

 

 

frequency

 

 

 

 

 

 

 

 

 

setting (2)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Jump

JUMP F3

0000.0 Hz

0 Hz

0 to 400 Hz

 

 

 

 

 

frequency

 

 

 

 

 

 

 

 

 

setting (3)

 

 

 

 

 

 

 

 

 

Jump

JUMP W

0.5 Hz

0.5 Hz

0 to 9.9 Hz

• The frequency width where

 

 

 

 

frequency

 

 

 

 

frequencies are jumped is set.

 

 

 

 

width setting

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

21

F-28

STOP key

STOP-SW

ON

ON

ON: STOP key

Whether or not to make the

 

 

 

 

validity

 

 

 

valid

STOP key valid during terminal

 

 

 

 

selection

 

 

 

OFF: STOP key

running is selected. In the

 

 

 

 

during

 

 

 

invalid

Remote mode, the STOP key is

 

 

 

 

terminal

 

 

 

 

always valid.

 

 

 

 

running

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

22

F-29

Running

F/R SW

FRE

FRE

FWD/REV/

FWD: Only forward run

 

 

 

 

direction

 

 

 

FRE

REV: Only reverse run

 

 

 

 

selection

 

 

 

 

FRE: Both forward run and

 

 

 

 

 

 

 

 

 

reverse run valid

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Reverse run

F/R PREV

OFF

OFF

ON/OFF

Reverse run prevention

 

 

 

 

prevention

 

 

 

 

ON:

 

 

 

 

selection

 

 

 

 

OFF:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Reduced

F/R RVS

6

6

0 to 6

 

 

 

 

 

voltage

 

 

 

 

 

 

 

 

 

soft start

 

 

 

 

 

 

 

 

 

setting

 

 

 

 

 

 

 

23

F-30

Maximum

F-MAX-L

120 Hz

120 Hz

120/400 Hz

Maximum frequency switching:

 

 

 

 

frequency

 

 

 

 

120: 120 Hz 400: 400 Hz

 

 

 

 

selection

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

24

F-31

Analog input

IN ANA

10 V

10 V

10/5

Input voltage maximum level

 

 

 

External

voltage

 

 

 

 

10: Max. 10 V 5: Max. 5 V

 

 

 

analog

selection

 

 

 

 

 

 

 

 

frequency

External

IN EXS

0000.0 Hz

0 Hz

0 to 120.0 (400)

• Frequency at which the

 

 

 

command

frequency

 

 

 

 

external input starts

 

 

 

 

start setting

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

External

IN EXE

0000.0 Hz

0 Hz

0 to 120.0 (400)

• Frequency at which the

 

 

 

 

frequency

 

 

 

 

external input is maximized

 

 

 

 

end setting

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

External

IN EX%S

000%

0%

0 to 100

• Input start level

 

 

 

 

frequency

 

 

 

 

 

 

 

 

 

start setting

 

 

 

 

 

 

 

 

 

rate

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

External fre-

IN EX%E

100%

100%

0 to 100

• Input maximum level

 

 

 

 

quency end

 

 

 

 

 

 

 

 

 

setting rate

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

External

IN LEVEL

0 Hz

0 Hz

0 Hz/ExS

EXS: Start at EX%S setting

 

 

 

 

command

 

 

 

 

rate or less

 

 

 

 

start point

 

 

 

 

 

 

 

 

 

selection

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12-10

Page 101
Image 101
Hitachi J300U Series instruction manual 12-10