Extension

function

code

Contents and display

Set the limits of frequency setting within the

 

 

start frequency adjustment range and

 

 

maximum frequency setting range. When a value beyond the limits is inputted from the operator, it will not be stored. Even if a value beyond the limits is inputted as external analog input, the set value will not be changed.

Frequency upper, lower limiter

Maximum frequency limiter

2

FUNC

FUNC

Minimum frequency limiter

2

FUNC

FUNC

.

.

(400)

Setting example

1(When an upper limit of 45 Hz and a lower limit of 20 Hz are set)

Initial value

Output frequency

 

 

 

(60 Hz)

 

 

 

 

 

Upper limiter

45

 

range

 

 

 

 

 

 

 

 

 

 

Settable

 

 

(400)

Lower limiter

20

 

 

 

 

 

1

 

0

 

 

 

 

 

 

 

Frequency command

 

 

 

 

 

 

 

 

 

 

(F-SET)

Initial value

NOTE: Setting conditions

 

0 Hz or upper limit lower limit

 

When 0 Hz is set, the limiters will not operate.

Jump frequency setting 1

Jump frequency setting 2

Jump frequency setting 3

To avoid a resonance with the load, the frequencies at up to 3 points can be jumped. The setting order and the execution order may be changed.

The frequency equivalent to the jump frequency setting width (± 0.5 Hz) (Note 1) cannot be set as a jump frequency.

NOTE 1 : The jump frequency can be set by the remote operator.

NOTE 2 : As to the frequencies which are set by the jump frequency setting function, the set frequencies are jumped but the output frequencies pass.

 

 

 

 

 

Setting example

f

 

f

 

 

Jump frequency 1: 10 Hz

 

 

 

 

 

Jump frequency 2: 30 Hz

 

 

Jump frequency 3: 45 Hz

Output

Jump frequency width: 0.5 Hz

 

frequency

f

 

 

 

0

0

 

 

 

 

 

 

 

 

 

Set frequency (V)

 

 

Output frequency (V)

45

Adjustment range

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

30

 

 

 

 

 

 

 

In the case

 

 

 

 

 

 

 

 

 

In the case

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

of jump frequency 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

of jump frequency 2

10

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

 

 

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

In the case

0

 

 

 

 

 

 

 

 

 

 

 

 

 

FUNC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Initial value

 

 

 

 

 

 

 

(V)

 

 

 

 

 

 

of jump frequency 3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Speed command

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Deceleration

 

 

0.5 Hz

frequency

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Frequency which

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FUNC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

➤ ➤

0.5 Hz

 

jumps by 1.0 Hz

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Acceleration

 

 

 

 

7-17

Page 57
Image 57
Hitachi J300U Series instruction manual Frequency upper, lower limiter