12.4Protection function display list when the remote operator is used
There are protection functions for overcurrent, overvoltage, and undervoltage provided to protect the inverter. When one of the functions is performed, the output is cut off, and the motor is put into the free run state, and the status is kept until the inverter is forced to reset.
|
| Remote operator(DOP) | |
Name | Digital operator display | copy unit(DRW)display | |
|
| ERR1 ✽ ✽ ✽ ✽ | |
| Constant speed | OC.Drive | |
Overcurrent | Deceleration | OC.Decel | |
protection | |||
|
| ||
| Acceleration | OC.Accel | |
Overload |
| Over.L | |
protection |
| ||
|
| ||
Braking resistor |
| OL.BRD | |
overload |
| ||
|
| ||
Overvoltage |
| Over.V | |
protection |
| ||
|
| ||
EEPROM error |
| EEPROM | |
Undervoltage |
| Under.V | |
protection |
| ||
|
| ||
CT error |
| CT | |
CPU error |
| CPU | |
External trip |
| EXTERNAL | |
USP error |
| USP | |
Ground fault |
| GND.Flt | |
protection |
| ||
|
|
Other displays
|
| Remote operator(DOP) | |
Name | Digital operator display | copy unit(DRW)display | |
|
| ERR1 ✽ ✽ ✽ ✽ | |
Input overvoltage |
| OV.SRC | |
Instantaneous |
| ||
power failure |
| ||
|
| ||
Option connec- | Option 1 | NG.OP1 | |
|
| ||
tion error | Option 2 | NG.OP2 | |
| |||
Option PCB | Option 1 | OP1 | |
error |
|
| |
(NOTE 2) | Option 2 | OP2 | |
Phase failure | (NOTE 1) | PH.Fail | |
protection error | |||
|
| ||
| Constant speed | PM.Drive | |
Power module | Deceleration | PM.Decel | |
protection | Acceleration | PM.Accel | |
| |||
| Stop | PM.ERR | |
Undervoltage |
| UV.WAIT | |
standby |
| ||
|
|
For error contents, see page 8-1.
|
| Display | Cause | Description |
| |
|
|
|
| Communication error | This is displayed when an error occurs between the inverter and remote operator. | |
|
|
|
| *=1. Protocol error | When the STOP key or another key is pressed, the original display appears. | |
|
| |||||
|
| =2. | When the original display does not appear, turn the power off and then on once | |||
|
|
|
| |||
|
|
|
|
| again. Check whether any connectors are loose. |
|
|
|
|
|
|
| |
|
|
|
| During inverter running | If one of the displays on the left occurs when the copy unit is used to read or copy, | |
|
| |||||
|
| take the corresponding countermeasure. |
| |||
|
|
|
|
|
| |
|
|
|
|
| • INV. RUN: Stop the running. |
|
|
|
|
|
|
| |
|
| Under inverter trip |
| |||
|
| • INV. TRIP: Press the STOP key to release the trip. |
| |||
|
|
|
|
| • INV. TYPE: The inverter type of the copy source is different from that of the | |
|
|
|
| Inverter type mismatch | ||
|
| copy destination. Use the same type of inverter to read or copy. | ||||
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| Inverter read lock | The fourth switch of the DIP switch on the back of the remote operator is ON. | |
|
| |||||
|
| When reading data, turn the switch OFF. |
| |||
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| Instantaneous power | This indicates that the instantaneous power failure restart function is being performed. | |
| RESTART | ✽ ✽ ✽ .✽ s |
| |||
|
|
|
| failure restart function in | • RESTART: 0 start is in execution. |
|
|
|
|
|
| ||
| ADJUST | ✽ ✽ ✽ .✽ s |
| operation | • ADJUST: Frequency matching is in execution. |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| Undervoltage | The supply voltage is lowered to the undervoltage level. When this display | |
| UV WAIT |
|
| |||
|
|
| appears, turn the power on once again. |
| ||
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| Power OFF | The undervoltage after the power is turned off is displayed. |
| |
| POWER OFF |
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| This is displayed after the autotuning measurement is finished. |
|
| Tuning OK |
|
| Autotuning function end |
| |
|
|
|
| • Tuning OK: The measurement terminates normally. |
| |
|
|
|
| display |
| |
| Tuning NG |
|
| • Tuning NG: The measurement fails. |
| |
|
|
|
|
| ||
|
|
|
|
|
| |
|
|
|
|
|
|
|
| NOTE 1: Power OFF during motor deceleration may cause an input phase failure error. |
| ||||
| NOTE 2: When the |
| ||||
|
|
|
|
| Digital operator | DOP, DRW |
|
|
|
|
| display |
|
Encoder line break: Overspeed: Positioning error: Thermistor line break: Motor overheat:
Malfunction or abnormality on
12-16
OP1 0 OP1 1 OP1 2 OP1 4 OP1 5 OP1 7