Operating with digital operator:

Runnign from external command:

Procedure

(1)Turn on ELB to supply power to the inverter. Make sure that the POWER LED on the digital operator turns ON.

(2)Press the FUNC key once to display .

(3)

Press 2 of the digital operator four times to display

 

 

 

 

.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(4)

Press the

 

FUNC

 

key and then press the 2

(4)

Press the

 

 

 

key and then press the 2

 

 

 

FUNC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

key to set

 

 

 

 

. Press the

FUNC

 

key to

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

key to set

 

 

 

 

. Press the

FUNC

key to

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

establish the data.

 

 

 

 

 

 

 

establish the data.

 

 

(5)

Press the

1 key four times to display

 

 

 

(5)

Press the

 

1 key four times to display

 

 

 

 

.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(6)

Press 1 of the digital operatort five times

 

 

 

 

 

 

 

 

 

 

 

(6) Short the terminals FW and P24 (CM1*)

 

to dispaly

 

 

 

 

 

.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

of the control terminal block.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(7)

Press the

 

FUNC

 

key and then the 1

key

(7) Apply a voltage between the terminals O

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

so as to increase to frequency or the

2

 

 

 

 

and L to start running.

 

key so as to decrease the frequency.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(When the

1 or

 

2 key is pressed con-

(8) Open the terminals FW and P24 (CM1*)

 

tinuously, the frequency is changed con-

 

 

of the control terminal block to stop decel-

 

tinuously.)

 

 

 

 

 

 

 

 

 

 

eration.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

When the

FUNC

key is pressed,

 

 

 

is

*: Symbols are indicated for Sink type wiring.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

displayed.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Refer to page 5-5.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(8)Check the output frequerncy and rotation direction. When the 1 or 2 key is

pressed to display and then the

FUNC key is pressed, the rotation direction

can be checked.

 

 

 

indicates forward

rotation and

 

 

 

 

indicates reverse

r

 

 

 

rotation. When the

rotation direction is

checked, press the

 

FUNC

key. When the

rotation direction

 

be found, operate

cannot

the equipment at a low frequency to check

the rotation direction.

 

 

(9) Presst the

RUN

key. The equipment

 

 

 

 

 

starts running.

 

 

(10)Press the STOP/RESET key. The equipment decelerates and stops.

6-4

Page 38
Image 38
Hitachi J300U Series Key and then press Press, Key to Key to set Press, Key. When, Rotation direction, Presst